Simulator Configuration Guide for Synopsys Models

More documents

Recommendations

Info

Chapter 2: Using VCS with Synopsys ModelsSimulator Configuration GuideRun your simulation as usual. After running the vcs compiler, you should see acompiled simv file. To run your simulation, type in simv.You need an additional passcode to use the hardware model interface. If you do not havea passcode, contact VCS Simulation Support at 800-837-4564.VCS UtilitiesIf you want to turn on test vector logging or timing measurement, you can invoke tasks'lm_log', 'lm_log_off', 'lm_measure_time', or 'lm_measure_time_off'.instance_name.lm_measure_time;instance_name.lm_measure_time_off;where instance_name is a string that is the hierarchical path name of the instance for thehardware model. For example, assuming that our instance is top.hwm_1 with thesefeatures, it would look like the following example:module top;TILS299 hwm_1();initial begintop.hwm_1.lm_measure_time;top.hwm_1.lm_log ("file_name");#7000;endtop.hwm_1.lm_measure_time_off;top.hwm_1.lm_log_off;58 Synopsys, Inc. October 6, 2003
Simulator Configuration GuideChapter 3: Using ModelSim Verilog with Synopsys Models3Using ModelSim Verilog withSynopsys ModelsOverviewThis chapter explains how to use SmartModels, FlexModels, DesignWare MemoryModels, and hardware models with MTI Verilog (ModelSim/VLOG.). The proceduresare organized into the following major sections:● “Setting Environment Variables” on page 59● “Using SmartModels with ModelSim Verilog” on page 61● “Using FlexModels with ModelSim Verilog” on page 63● “Using DesignWare Memory Models with ModelSim Verilog” on page 66● “Using Hardware Models with ModelSim Verilog” on page 68Setting Environment VariablesFirst, set the basic environment variables. If you are not using one of the model types,skip that step. In some cases the procedures that follow in this chapter include steps forsetting additional environment variables.1. Set the LMC_HOME environment variable to point to the location of yourSmartModel, FlexModel, or DesignWare Memory Model installation tree, asfollows:% setenv LMC_HOME path_to_models_installation2. Make sure ModelSim Verilog is set up properly in your environment.October 6, 2003 Synopsys, Inc. 59
Page 1:
Simulator ConfigurationGuide for Sy
Page 4 and 5:
ContentsSimulator Configuration Gui
Page 6 and 7:
ContentsSimulator Configuration Gui
Page 8 and 9: FiguresSimulator Configuration Guid
Page 10 and 11: TablesSimulator Configuration Guide
Page 12 and 13: PrefaceSimulator Configuration Guid
Page 18 and 19: Chapter 1: Using Synopsys Models wi
Page 40 and 41: Chapter 2: Using VCS with Synopsys
Page 60 and 61: Chapter 3: Using ModelSim Verilog w
Page 74 and 75: Chapter 4: Using ModelSim VHDL with
Page 90 and 91: Chapter 5: Using NC-Verilog with Sy
Page 108 and 109:
Chapter 6: Using NC-VHDL with Synop
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Chapter 7: Using QuickSim II with S
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
.Chapter 7: Using QuickSim II with
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Chapter 8: Using Scirocco with Syno
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Chapter 9: Using VERA with Synopsys
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Chapter 10: Using SystemC with Syno
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Appendix A: Using LMTV with Synopsy
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Appendix B: Using Custom Memory Mod
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
IndexSimulator Configuration Guide$
Page 304 and 305:
IndexSimulator Configuration Guidef
Page 306 and 307:
IndexSimulator Configuration GuideL
Page 308 and 309:
IndexSimulator Configuration GuideQ
Page 310 and 311:
IndexSimulator Configuration GuideS
show all

Simulator Configuration Guide for Synopsys Models

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?