Simulator Configuration Guide for Synopsys Models

More documents

Recommendations

Info

Chapter 7: Using QuickSim II with Synopsys ModelsSimulator Configuration GuideEditing PropertiesAdding or changing the value of any DWMM model property causes the simulator toreevaluate that property and initialize the model to its power-up state.Use the following menu selections to change a property:●●●Edit > Properties > AddEdit > Properties > ChangeEdit > PropertiesChanging Timing ModesDWMM models support minimum, typical, and maximum timing modes. Use thefollowing menu selection to change the timing mode of specific model instances:Setup > Kernel > Change > Timing ModeUnit-delay mode is supported through the model’s TimingVersion property (though notthrough the timing mode value). To enable a DWMM model to run in unit-delay mode,change the model’s TimingVersion property value to “none”.Constraint CheckingDWMM models use the MessageLevel property to enable or disable timing constraintchecking (such as setup and hold):● To enable constraint checking, set bit 2 of the MessageLevel property value to 1.● To disable constraint checking, set bit 2 to 0.162 Synopsys, Inc. October 6, 2003
Simulator Configuration GuideChapter 7: Using QuickSim II with Synopsys ModelsDWMM Custom SymbolsSynopsys provides symbols representing a simple pin interface for DWMMs. However,in some situations you may need to create custom symbols:●●●To conform to internal drafting requirements.To match external drafting specifications (for example, military specifications).To make a symbol match a component’s pinout.To create custom symbols, you can do the following:● Modify a standard DWMM symbol. Start with the DWMM symbol and modify itto match your drafting requirements. The value of the user PIN property can now bechanged without corrupting the value of the compiled PIN property.● Create a new symbol. Create a symbol with your pin values, find thecorresponding pin names used by the model, and change the user pin values to thosenames.To create a custom symbol for a DWMM model, use the procedure outlined forSmartModels: see “Custom Symbols” on page 144.Required DWMM Symbol PropertiesThe following symbol properties are required to interface with a DWMM model:●●●●modelpinpintypeswift_templateRefer to Table 20 for information about the required symbol properties. In addition, seeTable 19 and Table 21 for information about DWMM model configuration propertiesand optional model properties.October 6, 2003 Synopsys, Inc. 163
Page 1:
Simulator ConfigurationGuide for Sy
Page 4 and 5:
ContentsSimulator Configuration Gui
Page 6 and 7:
ContentsSimulator Configuration Gui
Page 8 and 9:
FiguresSimulator Configuration Guid
Page 10 and 11:
TablesSimulator Configuration Guide
Page 12 and 13:
PrefaceSimulator Configuration Guid
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Chapter 1: Using Synopsys Models wi
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Chapter 2: Using VCS with Synopsys
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Chapter 3: Using ModelSim Verilog w
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Chapter 4: Using ModelSim VHDL with
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Chapter 5: Using NC-Verilog with Sy
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Chapter 6: Using NC-VHDL with Synop
Page 110 and 111:
Chapter 6: Using NC-VHDL with Synop
Page 112 and 113: Chapter 6: Using NC-VHDL with Synop
Page 124 and 125: Chapter 7: Using QuickSim II with S
Page 174 and 175: .Chapter 7: Using QuickSim II with
Page 192 and 193: Chapter 8: Using Scirocco with Syno
Page 208 and 209: Chapter 9: Using VERA with Synopsys
Page 210 and 211: Chapter 9: Using VERA with Synopsys
Page 212 and 213:
Chapter 9: Using VERA with Synopsys
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Chapter 10: Using SystemC with Syno
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Appendix A: Using LMTV with Synopsy
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Appendix B: Using Custom Memory Mod
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
IndexSimulator Configuration Guide$
Page 304 and 305:
IndexSimulator Configuration Guidef
Page 306 and 307:
IndexSimulator Configuration GuideL
Page 308 and 309:
IndexSimulator Configuration GuideQ
Page 310 and 311:
IndexSimulator Configuration GuideS
show all

Simulator Configuration Guide for Synopsys Models

Create successful ePaper yourself

Delete template?

Save as template?