Avery® DOL 3100 Matt - promotional (PDF) - Spandex

Avery ® DOL 3100 MattMatt Clear Promotional OverlaminateFeatures• Good UV protection• Improves inkjet outdoor image durability up to 1 year• Improves solvent inkjet outdoor image durability up to 3 years• Good abrasion resistance• Excellent adhesion to graphic materials• Excellent transparency• Matt finish for low-glare applications• Excellent value for moneyDescriptionFilm: 80 micron matt clear UVstable monomeric calenderedvinyl overlaminateAdhesive: Permanent acrylicBacking: One side coatedKraft paper, 87gsmOutdoor life: Up to 3 yearsConversion*Flat bed cuttersFriction fed cuttersDie cuttingThermal transferScreen printingCold overlaminatingEstat printingWater based inkjetSolvent inkjetUV Cured inkjetCommon Applications• Exhibitions• Indoor advertising• Point of purchase• Windows• Real estate signs• Outdoor advertisingStandardsAS/NZS 4586:2004 Standard slip resistance classification of new pedestrian surfaces: Appendix A, B Dual Classification: XFIn order to interpret the classifications, please refer to Standards Australia Handbook 197, An Introductory Guide to the SlipResistance of Pedestrian Surface Materials, which recommends minimum classifications for a wide variety of locations.ApplicationsFor processing tips and reference guides please refer to Avery Instructional Bulletins:• 1.18 Application and Maintenance of Avery ® Floor Graphics• 4.06 Processing Tips for Avery DOL FilmsUsesAvery DOL 3100 is a matt monomeric calendered overlaminate designed foruse as a protective overlaminating film for digitally printed images suitable forindoor or short term outdoor images on flat surfaces.Graphics and Reflective Products Division Asia Pacificwww.averygraphics.com

Avery ® DOL 3100 Matt Rev: 20081017-1GeneralCalliper, facefilm ISO 534 80 micronCalliper, facefilm & adhesive ISO 534 110 micronDimensional stability0.3 mm maxAdhesion, initial ASTM 1000, stainless steel 550 N/mAdhesion, ultimate ASTM 1000, stainless steel 900 N/mFlammabilityShelf life Stored at 22° C/50-55 % RH 2 yearsSelf extinguishingDurability ** Vertical exposure Up to 3 yearsSlip resistance AS/NZS 4586:2004 Appendix A, B DualClassification: XFImportantInformation on physical characteristics isbased upon tests we believe to be reliable.The values listed herein are typical valuesand are not for use in specifications.They are intended only as a source ofinformation and are given withoutguarantee and do not constitute awarranty. Purchasers should independentlydetermine, prior to use, the suitability ofany material for their specific use.All technical data is subject to changewithout prior notice.WarrantyThermalLamination temperatureSee relevant technical bulletinsService temperature range- 40 o C to + 80 o CChemicalResistant to most petroleum based oils, greases, and aliphatic solventsResistant to mild acids, alkalis and saltsAvery ® materials are manufactured undercareful quality control and are warranted tobe free from defect in material andworkmanship. Any material shown to oursatisfaction to be defective at the time ofsale will be replaced without charge. Ouraggregate liability to the purchaser shall inno circumstances exceed the cost of thedefective materials supplied. No salesman,representative or agent is authorised togive guarantee, warranty, or make anyrepresentation contrary to the foregoing.All Avery ® materials are sold subject to theabove conditions, being part of ourstandard conditions of sale, a copy ofwhich is available on request.**DurabilityDurability is based on exposure conditionsin the Asia Pacific region. Actualperformance life will depend on substratepreparation, exposure conditions andmaintenance of the marking. For instance,in the case of signs facing north in thesouthern hemisphere or south in thenorthern hemisphere; in areas of long hightemperature exposure such as northernAustralia; in industrially polluted areas orhigh altitudes, exterior performance willbe decreased.*Compatible with most printer and inkcombinations. Test prior to use.***Information unavailable at time ofprinting.Test MethodsDimensional stability:Is measured on a 150 x 150 mm aluminium panel to whicha specimen has been applied; 72 hours after applicationthe panel is exposed for 48 hours to + 70°C, after whichthe shrinkage is measured.Adhesion:(FTM-1, FINAT) is measured by peeling a specimen at a180° angle from a stainless steel or float glass panel, 24hours after the specimen has been applied understandardised conditions. Initial adhesion is measured 20minutes after application of the specimen.Flammability:A specimen applied to aluminium is subjected to the flameof a gas burner for 15 seconds. The film should stopburning within 15 seconds after removal from the flame.Temperature range:A specimen applied to stainless steel is exposed at highand low temperatures and brought back to roomtemperature. 1 hour after exposure the specimen isexamined for any deterioration. Note: Prolongedexposure to high and low temperatures in the presence ofchemicals such as solvents, acids, dyes, etc. mayeventually cause deterioration.Chemical Resistance:All chemical tests are conducted with test panels to whicha specimen has been applied. 72 hours after applicationthe panels are immersed in the test fluid for the given testperiod. 1 hour after removing the panel from the fluid, thespecimen is examined for any deterioration.Corrosion Resistance:A specimen applied to aluminium is exposed to saline mist(5% salt) at 35ºC. After exposure, the film is removed andthe panel is examined for traces of corrosion.Graphics and Reflective Products Division Asia Pacificwww.averygraphics.com