general indexindexsupports, special enclosures and accessories● special enclosures with dual outlets, widened, w/o outlets, for ribbon cables, for round cables, coupling, central lever 236 ÷ 243● CG and MG types, high IP68 protection rating enclosures 244 ÷ 252● T-BOX coupling with 1 or 2 branches 254 ÷ 255● COB type mountings for panels 256 ÷ 260● miscellaneous auxiliaries and accessories 262 ÷ 263● PCB interfaces 264● Constantan (CuNi) and iron (Fe) crimping contacts 265● anchors for cables inside and outside enclosures, coding pins 266 ÷ 271● CKM T terminal connec<strong>to</strong>r 272● insert joining block, metal replacement handles, carrying cover, enclosure removal pliers 273 ÷ 274● SUB-K insert plates, control equipment kits, plate only (SDS) and plate with enclosure (CHSDS) 275 ÷ 276● blanking or adapter plates, pliers for MIXO BUS connec<strong>to</strong>rs removal 277● adapters for RJ45 connec<strong>to</strong>rs, coupling for RJ45 connec<strong>to</strong>r 278 ÷ 279● connec<strong>to</strong>rs for compliance with DESINA ® standard 280 ÷ 291pagecrimping <strong>to</strong>olspage● crimping concept 293 ÷ 295● manual <strong>to</strong>ols 296 ÷ 303● pneumatic <strong>to</strong>ols 304 ÷ 307● wire stripping - crimping machine 308 ÷ 309● RJ45 crimp <strong>to</strong>ol 310Part Nos. and indexpage● Part Nos. list 312 ÷ 3222
general overview of <strong>the</strong> multipole connec<strong>to</strong>r production for industrial purposes and accessoriesInsertsThe inserts are made of self-extinguishing <strong>the</strong>rmoplastic resin UL 94 V0, normally used for applications in a maximum ambience temperature of 125 °C. The specialversions for use with a maximum ambience temperature of 180 °C are made of PPS. Different conduc<strong>to</strong>r connection techniques are available: screw connections, crimpconnections, or flexible spring connections. The contacts are in silver or gold plated brass. The inserts are numbered on both sides by laser printing or moulded.There is a large number of versions of inserts selected on <strong>the</strong> basis of <strong>the</strong> rated voltage (from 50V <strong>to</strong> 5000V), <strong>the</strong> rated current (from 10A <strong>to</strong> 100A max), <strong>the</strong> number ofpoles, <strong>the</strong> different load combinations required (power and signal poles within <strong>the</strong> same insert).The inserts are approved in conformance with <strong>the</strong> major conformity marks including E.generalThe RoHS (2002/95/EC) and RAEE (2002/96/EC) Directives● The RoHS 2002/95/EC Directive bans <strong>the</strong> use of some harmful substances used in new electrical and electronic equipment commercially available from <strong>the</strong> 1st of July2006 (<strong>the</strong> exceptions for some applications are enclosed in <strong>the</strong> Directive Enclosure and in some later decisions made by <strong>the</strong> EU Commission 1)). The banned and/orrestricted substances are: Lead, Mercury, Cadmium, Hexavalent Chromium, Poly-Brominated By-Phenyls and Poly-Brominated Dy-Phenyl E<strong>the</strong>rs (PBB andPBDE respectively, fire retardant substances for <strong>the</strong>rmoplastic materials).● The RAEE 2002/96/EC Directive (with its later amendment 2003/108/EC) aims <strong>to</strong> recycle and reduce <strong>the</strong> waste produced by electrical and electronic equipment. It alsopromotes recycling and reusing such technological waste and establishes ambitious recovery rate targets, which vary according <strong>to</strong> <strong>the</strong> types of products involved. Themanufacturers or <strong>the</strong>ir agents in <strong>the</strong> EU must ensure that <strong>the</strong> equipment sold after <strong>the</strong> 13th of August 2005 listed in <strong>the</strong> Enclosure I A and illustrated in <strong>the</strong> Enclosure I Bof this Directive is collected, treated and recycled (<strong>the</strong> deadline varies from country <strong>to</strong> country. In Italy, <strong>the</strong> deadline has been postponed <strong>to</strong> 31/12/2007, awaiting forapproval by <strong>the</strong> required executive Ministerial Decrees).As a manufacturer of electrical equipment and components for industrial use, I.L.M.E. acknowledges <strong>the</strong> regulations introduced by <strong>the</strong>se Directives. The above mentionedDirectives are already effective in almost all EU countries. For <strong>the</strong> products described in this Catalogue, although <strong>the</strong> usage restriction of <strong>the</strong> above mentionedhazardous substances is not legally applicable (none of our product does in fact belong <strong>to</strong> any of <strong>the</strong> categories described and illustrated in <strong>the</strong> RoHS and RAEEDirectives), <strong>the</strong> “RoHS compliance” may become important and many of our cus<strong>to</strong>mers may require its compliance. We have <strong>the</strong>refore carried out <strong>the</strong> corrective actions,which have led <strong>to</strong> <strong>the</strong> “RoHS compliance” of all our products, wherever required. I.L.M.E. products sold after <strong>the</strong> 1st of July 2006 do not contain any of <strong>the</strong> restrictedsubstances in higher concentration than those allowed by <strong>the</strong> RoHS directive and by <strong>the</strong> later associated Decisions taken by <strong>the</strong> EU Commission.1) At <strong>the</strong> time of publication of this Catalogue, <strong>the</strong> following EU Commission Decisions were available: 2005/618/EC, of 18 August 2005, 2005/717/EC, of 13 Oc<strong>to</strong>ber2005, 2005/747/EC, of 21 Oc<strong>to</strong>ber 2005, 2006/310/EC, of 21 April 2006, 2006/690/EC, 2006/691/EC, 2006/692/EC, of 12 Oc<strong>to</strong>ber 2006.The heavy duty multipole connec<strong>to</strong>rs for industrial purposes are used in electric and electronic machinery, control units, electric panels, controlequipment and wherever connections are required for power and signalling circuits. (N.B. <strong>the</strong> connec<strong>to</strong>rs must not be handled live).The connec<strong>to</strong>rs are in conformance with <strong>the</strong> standard DIN VDE 0627 (European standard IEC 61984) and where applicable, <strong>to</strong> <strong>the</strong> standard DIN43652 (European standard EN 175301-801 developed by CENELEC TC48B).3
Change language