Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
<strong>PRODUCT</strong> <strong>MANUAL</strong>L110E/L120E<strong>ATTACHMENTS</strong>
Table of contentsForeword ...................................................................................................................................................................................... 3Genuine attachments in general ............................................................................................................................. 4Abbreviation system ........................................................................................................................................................... 5Bucket fill factor ..................................................................................................................................................................... 6Bucket selection charts .................................................................................................................................................. 7Attachment bracket ............................................................................................................................................................. 8Selecting a bucket .............................................................................................................................................................. 9Wear parts .............................................................................................................................................................................. 10Adapters ................................................................................................................................................................................... 12Points .......................................................................................................................................................................................... 13Request for special attachments ........................................................................................................................ 14L110EOrdering No.General purpose bucketsIntended for bolted options onlySTE P 2,5-2,7 m 3 , 3.3-3.5 yd 3 93646, 80145 ....................................................................... 162,8-3,0 m 3 , 3.7-3.9 yd 3 80939, 93876 ....................................................................... 173,3 m 3 , 4.3 yd 3 93882 ........................................................................................... 183,0-3,3 m 3 , 3.9-4.3 yd 3 82396, 80872 ....................................................................... 19STE H 2,5-2,8 m 3 , 3.3-3.7 yd 3 93869, 80941 ....................................................................... 203,0-3,3 m 3 , 3.9-4.3 yd 3 93870, 93872 ....................................................................... 213,0-3,3 m 3 , 3.9-4.3 yd 3 82397, 80575 ....................................................................... 22Flat floor bucketsIntended for bolted options onlySTE P 3,0 m 3 , 3.9 yd 3 82117, 82360 ....................................................................... 24General purpose bucketsIntended for welded teeth options onlySTE P 3,0-3,3 m 3 , 3.9-4.3 yd 3 93881, 93883 ....................................................................... 263,3 m 3 , 4.3 yd 3 82590 ........................................................................................... 27STE H 3,0-3,3 m 3 , 3.9-4.3 yd 3 93871,93873 ........................................................................ 28Flat floor bucketsIntended for welded teeth options onlySTE P/H 3,0 m 3 , 3.9 yd 3 82118, 82361 ....................................................................... 30Rock bucketsIntended for welded teeth options onlySPN P 2,6 m 3 , 3.4 yd 3 93889 ........................................................................................... 322,9 m 3 , 3.8 yd 3 93890 ........................................................................................... 33SPN H 2,9 m 3 , 3.8 yd 3 93888 ........................................................................................... 34STE RO P 3,0 m 3 , 3.9 yd 3 93887 ........................................................................................... 36L120EOrdering No.General purpose bucketsIntended for bolted options onlySTE P 2,5-2,7 m 3 , 3.3-3.5 yd 3 93646, 80145 ....................................................................... 382,8-3,0 m 3 , 3.7-3.9 yd 3 80939, 93876 ....................................................................... 393,0-3,3 m 3 , 3.9-4.3 yd 3 82396, 80872 ....................................................................... 403,5 m 3 , 4.6 yd 3 82024 ........................................................................................... 413,3-3,5 m 3 , 4.3-4.6 yd 3 93882, 93884 ....................................................................... 421
Table of contentsL120EOrdering No.STE H 2,5-2,8 m 3 , 3.3-3.7 yd 3 93869, 80941 ....................................................................... 433,0-3,3 m 3 , 3.9-4.3 yd 3 93870, 93872 ....................................................................... 443,5 m 3 , 4.6 yd 3 93875 ........................................................................................... 453,0-3,3 m 3 , 3.9-4.3 yd 3 82397, 80575 ....................................................................... 463,5 m 3 , 4.6 yd 3 82602 ........................................................................................... 47Flat floor bucketsIntended for bolted options onlySTE P 3,0-3,4 m 3 , 3.9-4.4 yd 3 82117, 82608 ....................................................................... 48STE H 3,0-3,4 m 3 , 3.9-4.4 yd 3 82360, 82595 ....................................................................... 49General purpose bucketsIntended for welded teeth options onlySTE P 3,0-3,3 m 3 , 3.9-4.3 yd 3 93881, 93883, 82590 .................................................. 50STE H 3,0-3,3 m 3 , 3.9-4.3 yd 3 93871, 93873, 80576 .................................................. 51Flat floor bucketsIntended for welded teeth options onlySTE P 3,0-3,4 m 3 , 3.9-4.4 yd 3 82118, 82607 ....................................................................... 52STE H 3,0-3,4 m 3 , 3.9-4.4 yd 3 82361, 82596 ....................................................................... 53Rock bucketsIntended for welded teeth options onlySPN P 2,6 m 3 , 3.4 yd 3 93889 ........................................................................................... 542,9 m 3 , 3.8 yd 3 93890 ........................................................................................... 55SPN H 2,9 m 3 , 3.8 yd 3 93888 ........................................................................................... 56STE RO P 3,0 m 3 , 3.9 yd 3 93887 ........................................................................................... 58L110E – L120EOrdering No.Refuse bucketsIntended for bolted options onlyREF P 5,3 m 3 , 6,9 yd 3 82511, 82512 .................................................................. 60Light material bucketsLM P/H 5,5 m 3 , 7.2 yd 3 92690, 92689 .................................................................. 62LM H 9,5 m 3 , 12.4yd 3 92684 ....................................................................................... 63Hi-Tip light material bucketsHIT P/H 5,0-7,0 m 3 , 6.5-9.2 yd 3 82042,82043, 82040, 82041 ........................... 64HIT P/H 9,5 m 3 , 12.4 yd 3 82044, 82045 .................................................................. 65Log grapples ........................................................................................................................................................................ 66HK OUT 80836 ....................................................................................... 67UNL GR H 1,8-2,4 m 2 , 19.4-25.8 ft 2 80834, 80831 .................................................................. 68SORT GR H 1,8-2,4 m 2 , 19.4-25.8 ft 2 80835, 80832 .................................................................. 69GP GR H 1,3 m 2 , 14.0 ft 2 82339, 82340 .................................................................. 70SWC H 0,5-2,0 m 2 , 5.4-21.5 ft 2 82131, 82132, 82133 .............................................. 71TROP GR H 1,1 m 2 , 11.8 ft 2 94574 ....................................................................................... 722Fork attachments .............................................................................................................................................................. 73Material handling arms ................................................................................................................................................ 82Other attachments ........................................................................................................................................................... 84Allied suppliers ................................................................................................................................................................... 90
ForewordStandardsThe standards and/or recommendations applied by VolvoConstruction Equipment refer to ISO, SAE and EN standards.ISO – the International Standards Organization – is aninternational organization dedicated to standardization.SAE – stands for the Society of Automotive Engineers, anAmerican organization dedicated to standardization.EN – stands for European Norm – a European standardwithin the framework of the EU Machinery Directive.Depending on the application and various materials,earth densities, sizes of materials, etc., an alternativetype/capacity of attachment not indicated in this catalogmay be chosen after consulting with VolvoConstruction Equipment.Older attachments may be used on later Volvo wheelloader models provided the attachments have thesame or smaller capacity than recommended for thenew model, and if necessary, modifications regardingfitting are executed in compliance with recommendations.The data applies to Volvo L110E and L120E equippedwith standard boom (SB) and tires*:L110E – 23.5R25L120E – 23.5R25* Unless otherwise notedWeight and measuresThe following conversion factors are given to facilitate anynecessary calculations. Standard International (SI) unitsare used throughout the catalog.1 mm = 0.03937 in1 m = 3.281 ft = 39.37 in1 kg = 2.205 lb1 t = 1000 kg = 2205 lb1 kN = 102 kp = 224.8 lbf1 m 2 = 10.76 ft 21 m 3 = 1.308 yd 31 dm 3 (l) = 61.02 in 31 dm 3 /min = 1 l/min = 0.2642 US gal/min1 t/m 3 = 1.686 lb/yd 31 kW = 1.360 metric hp1km/h = 0.6214 mile/h1MPa = 10 bar = 10.20 kp/cm 2= 145 lbf/in 2 (psi)1 kp = 2.205 lbf1 Nm = 0.7376 lbf ft3
Genuine attachments in generalQualityThe hard and abrasive materials that constitute normalworking conditions have forced us to use high-gradesteels. Since conditions are not only severe, but alsovarying, mere strength is not enough – flexibility is alsorequired. Through extensive testing, we have developed alarge number of buckets for materials of differentdensities that permit optimum utilization of the machine’stipping load.Manufactured in EuropeMaximum strength and flexibility require perfect interplaybetween attachment and wheel loader. This interplaymust begin during the development of the differentcomponents. We have matched the buckets optimally toour loaders.The geometry of the loader unit and the shape of thebucket are intimately related. In order to calculate theoptimum bucket angle, plate thickness, bottom length,bucket width, etc., it is necessary to know the angles andother characteristics of the lift-arm system.The product sign plate affixed to all genuine attachmentsis the buyer’s guarantee the attachment has been testedand approved with respect to quality and function.The sign plate not only marks the attachment as genuine,it also serves as a certificate of identification.76Manufactured in North America1 2 3 4 5Volvo buckets are composed of through hardened andtempered, abrasion resistant steels in most parts.See declaration below:(Composition may depend on type and size of bucket.)Piece parts:Brinell Hardness:1. Bucket Shell 4002. Floor Reinforcements 4003. Cutting Edge 5004. Main Wear plates 500 (Bolt-on)5. Wear Plates, outer 4006. Side Cutter 4007. Side Sheet 4004
Abbreviation systemThe following abbreviation system is used for allVolvo Wheel Loader Attachments:Attachment typesAttachment fitting typeH Hook-onP Pin-onWear partsBOE Bolt-on EdgeBOT Bolt-on TeethPRD Pre-drilled Cutting EdgeSEG SegmentsTPoint or TeethGrapplesGPGRHKOUTOPCSORTGRSWCTRLGRTROPGRUNLGRWCPGeneral Purpose GrappleHeel/KickoutOne-Piece ClampSorting GrappleSwivel Wood ClampTree-Length GrappleTropical GrappleUnloading GrappleWear CapsOthersNOD Normal densitySS Side ShiftType of applicationGP General PurposeLM Light MaterialRO Rock ApplicationBucketsBW Bucket WidthCCB Coal Chopping BucketGRB Grading BucketHIT Hi-Tip BucketLM Light MaterialMPB Multi-Purpose BucketREF Refuse BucketSIT Side-Tip BucketSPN Spade Nose BucketSSB Sand Spreading BucketSTE Straight EdgePointsAM Abrasive MaterialAMX Abrasive Material, added wear metalGP General PurposeForksCOF Combi-ForkEXT ExtensionFFPSS Fork Frame W. Positioner andSide ShifterFLO FloatingFTPH Fork Tine Positioner HorizontalFTPV Fork Tine Positioner VerticalLUFT Lumber Fork TinesPAFF Pallet Fork FramePAFT Pallet Fork TinesSSFT Side Shifter Fork TinesOthersHD Heavy DutyLB Long BoomLD Light DutyMHA Material Handling ArmSB Standard BoomSTD StandardVariant DesignationsFF Flat Floor bucketLLeft HandR Right HandExamples:●●Straight edge general purpose bucket, pin-on, withteeth and segments 2,6 m 3 / 3.4 yd 3 .– STE P T SEG 2,6 m 3 / 3.4 yd 3 .Straight edge general purpose bucket, pin-on, withbolt-on cutting edges, 3,1 m 3 / 4.1 yd 3 .– STE P BOE 3,1 m 3 / 4.1 yd 3 .●Spade nose bucket, pin-on, with teeth and segments,2,7 m 3 / 3.5 yd 3 .– SPN P T SEG 2,7 m 3 / 3.5 yd 3 .5
Bucket fill factorGeneralTP Linkage27°21The bucket fill factor in rock isbetween 95 and 100%.21RockISO 7546 or SAE J742 heaped volume.The heap angle is 1:2 or 27°.The fill factor in aggregate(crushed material) is 100%.AggregateISO/SAE calculates with a perfect horizontal position ofthe bucket. When mounted on wheel loaders, however,the bucket tends to lean forward in carry position. Theangle also varies between competitors.The fill factor in sand and gravelwill be about 105%.TP LinkageSand and gravel27° 27°The linkage on a Volvo wheel loader allows the bucket tobe almost horizontal in carry position. When the materialhas a heap angle according to ISO/SAE, the bucket willcarry almost the ISO/SAE rated volume.The fill factor in material like clayand earth is 110% ormore.Z-bar linkageClay and earth27°27°Our competitors mainly use the Z-bar linkage, whichmakes the buckets lean more forward in carry position.A heap angle of 27° means that the bucket will carrymuch less than the ISO/SAE rated volume.The above illustrations show that Volvo wheel loaderswith TP Linkage achieve a much better bucket fillfactor than the Z-bar linkage in the same material.When choosing a bucket, remember that:1. Volvo wheel loaders with TP Linkage will give alarger heap than the same size competitive wheelloader in the same material.2. Choose the bucket in accordance to the wheelloader’s rated capacity and consider the materialtype, the density of the material and the actualtransported volume.6
Bucket selection chartThe choice of bucket is determined by the density ofthe material and the expected bucket fill factor. Theactual bucket volume is often larger than the rated capacitydue to the TP Linkage features: • Open bucket design.• Very good roll back in all positions. • Good bucketfill performance. The below example and table are intendedfor standard boom.Example: Sand and gravel. Fill factor ~ 105 %. Density1,65 t/m 3 /2695 lb/yd 3 .Result L110E: The 3,1 m 3 /4.1 yd 3 , bucket carries 3,3 m 3 /4.3 yd 3 .Result L120E: The 3,3 m 3 /4.3 yd 3 , bucket carries 3,5 m 3 /4.6 yd 3 .For optimum stability, always consult the bucket selectionchart.Material Bucket fill, Material density, ISO/SAE bucket Actual volume, m 3 /yd 3% ton/m 3 /lb yd 3 volume, m 3 /yd 3L110E L120E L110E L120E L110E L120EEarth/Clay ~110 ~1,80 ~2865 ~1,70 ~2865 2,9 3.9 3,0 3.9 ~3,2 ~4.3 ~3,3 ~4.3~1,70 ~2530 ~1,50 ~2530 3,1 4.3 3,3 4.3 ~3,4 ~4.7 ~3,6 ~4.7~1,50 ~2360 ~1,40 ~2360 3,4 4.6 3,6 4.6 ~3,7 ~5.0 ~4,0 ~5.0Sand/Gravel ~105 ~1,75 ~3950 ~1,75 ~3950 2,9 3.9 3,0 3.9 ~3,0 ~4.2 ~3,1 ~4.2~1,65 ~2695 ~1,65 ~2695 3,1 4.3 3,3 4.3 ~3,3 ~4.6 ~3,5 ~4.6~1,50 ~2530 ~1,50 ~2530 3,4 4.6 3,6 4.6 ~3,6 ~4.9 ~3,8 ~4.9Aggregate ~100 ~1,90 ~3200 ~1,90 ~3200 2,9 3.9 3,0 3.9 ~2,9 ~3.9 ~3,0 ~3.9~1,70 ~2865 ~1,70 ~2865 3,1 4.3 3,3 4.3 ~3,1 ~4.3 ~3,3 ~4.3~1,50 ~2695 ~1,60 ~2695 3,4 4.6 3,6 4.6 ~3,4 ~4.6 ~3,6 ~4.6Rock ≤ 100 ~1,80 ~3200 ~1,80 ~3200 2,7 3.9 3,0 3.9 ~2,7 ~3.9 ~3,0 ~3.9L110EType ofboomStandard boomType ofbucketRock General purposeLight material HI-TIPISO/SAE L110E Material density (t/m 3 )Bucketvolume0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 2,0P 2,9 m 33,2 2,9P 3.8 yd 34.2 3.8H 2,9 m 3H 3.8 yd 3 3,2 2,94.2 3.8P 3,1 m 3P 4.4 yd 3H 3,1 m 3H 4.4 yd 3P 3,4 m 3P 4.4 yd 3H 3,4 m 3H 4.4 yd 3P 2,7 m 3P 3.5 yd 3H 5,0 m 3H 6.5 yd 3H 7,0 m 3H 9.2 yd 39,512.45,06.53H 5,5 m 35,5H 7.2 yd 37.29,512.4H 9,5 m 3H 12.4 yd 3Bucket fill 674 1010 1350 1685 2020 2360 2700 3035 3370110% 105% 100% 95%Material density (lb/yd 3 )H 12.4 ydP = Pin-on H = Hook-on3,74.93,44.53,44.53,44.43,14.1P 3,0 m 3P 3.9 yd 3 3,03.9H 9,5 m 37,09.23,74.93,44.43,14.12,73.52,93.72,63.4L120EType ofboomStandard boomLong boomType ofbucketRock General purposeLight material HI-TIPGeneralpurposeLightmaterialISO/SAE L120E Material density (t/m 3 )Bucketvolume0,4 0,6 0,8 1,0 1,2 1,4 1,6 1,8 2,0P 3,1 m 3P 4.1 yd 33,4 3,14.5 4.1H 3,1 m 3H 4.1 yd 33,4 3,14.5 4.1P 3,4 m 3P 4.4 yd 3 3,7 3,44.9 4.4H 3,4 m 3H 4.4 yd 3P 3,6 m 3P 4.7 yd 3H 3,6 m 3H 4.7 yd 3P 2 ,7 m 3P 3.5 yd 3H 5,5 m 3H 7.2 yd 3H 9,5 m 3H 12.4 yd 3P 2,6 m 3P 3.4 yd 3H 2,6 m 3H 3.4 yd 3H 5,5 m 3H 7.2 yd 39,512.45,57.25,57.2Bucket fill 674 1010 1350 1685 2020 2360 2700 3035 3370110% 105% 100% 95%Material density (lb/yd 3 )P = Pin-on H = Hook-on4,05.23,74.94,05.23,64.73,44.43,64.7P 3,0 m 3P 3.9 yd 33,03.95,0H 5,0 m 36.5H 6.5 yd 37,09.2H 7,0 m 3H 9.2 yd 39,512.4H 9,5 m 3H 12.4 yd 32,93.82,93.82,63.42,63.42,73.52,83.72,22,63.4The size of rock buckets is optimized for optimal penetration and filling capability rather than the density of the material.7
Attachment bracketGeneralDifferent materials require different types of handling –not necessarily different machines. Volvo wheel loadersare continuously being developed to provide highercapacity within different fields of operation. Quick couplingof attachments permits effective utilization of thewheel loader where previously only special-purposemachines, such as fork-lift trucks and mobile cranes,could be used. The idea of interchangeable attachmentsis a unique solution that has made Volvo wheel loaders amarket leader.The attachment bracket with hydraulic locking is ruggedand easy to operate. Precision fit and quality engineeringwith large, rounded hooks make it easy to guide the attachmentonto the bracket. Thanks to the efficient designof the bracket, the difference in operating load betweendirect-mounted (pin-on) and bracket-mounted (hook-on)attachments is minimal. As designers of both the wheelloader and the attachment bracket, we have taken advantageof the unique opportunity to make the bracket anintegral part of the machine.Welded attachment bracketThis bracket provides optimal stability and break-out forces.However, it does not accept older generation attachmentsof Holms equipment, material handling arms andHi-Tip bucket without having the upper hooks on theattachment reworked.Cast steel attachment bracketThe cast steel attachment bracket has a very opendesign, therefore providing excellent visibility for the operator.The bracket fits both older generation machines withTP Linkage and hook-on attachments.Hydraulic lockingThe attachment can be locked to the attachment bracketfrom the operator's station via an interlocked switch on theinstrument panel.Locking pins are held securely in place by servo pressurefrom the hydraulic system.Attachment bracket in loggingIt makes sense to have several log grapples if you have towork with different timber sizes or you need to opti-mizecapacity in different operations. Our attachment bracketpermits rational utilization of several grapples or switchingto a wood chip bucket.Most of our log grapples are bracket-mounted, whichprovides versatility at the same cost as pin-on mountedgrapples.Bracket-mounted grapples do not project further forwardthan pin-on grapples, and the weight difference is negligible.Bracket-mounted log grapples offer greater flexibilitythan pin-on-mounted grapples.cabL110E/L120ECast steel WeldedAttachment bracket Order No 8084680847a Widthb Heightc Depthmm ft inmm ft inmm ft in12008503803'9"2'8"1'3"1210870430Weight kg lb 355 782 3053'9"2'9"1'4"6708
Selecting a bucketGeneralBucket volume alone is not an adequate measure of thecapacity of the loader. The crucial factor is the ability ofthe wheel loader to fill the bucket every pass. For thatreason, the right size and the right shape of the bucket isvery important. A large bucket can result in lower productivitybecause it is more difficult to fill, while a small bucketthat is easier to fill can increase productivity.A number of factors have to be taken into account, suchas the nature of the material being handled, the conditionof the wheel loader, the operator’s skill, and the transportdistance. If the transport distance is long, this may causespillage. Since all of these factors vary, a wide selectionof buckets is required in order to achieve maximum productivity.The Volvo attachment rangeoffers a wide selection.A B C D EAStraight edge general purpose bucketWhen fitted with bolt-on edges, it is the best choice forrehandling of loose material and aggregates in short cycle orload and carry operations. (Can also be fitted with bolt-onteeth and segments.)When fitted with welded teeth options and segments, it isthe best choice for loading easily broken material from banks.BFlat floor bucketThe bucket has the same advantages as the present gradingbucket, but is designed with a higher, general-purpose typeprofile for more versatility.The long, flat floor of the bucket makes it the ideal choice forearthmoving applications like landscaping, stripping topsoil,grading, or work in soft underfoot conditions.CStraight edge rock bucketThe best choice for loading easily broken material from banks.Recommended to be fitted with bolt-on edges or with teeth incombination with segments.DSpade nose rock bucketThe best choice for breaking out hard and stony material andshot rock. Recommended to be fitted with 1 1/2 leg typeadapters, points of AM type and segments. For gravel, fineshot rock and ore, it can be fitted with bolt-on edges insteadof teeth.EGrading bucketThis bucket has a long flat bottom. It is intended for earthmovingwork such as topsoil stripping, small-scale dozing,landscaping and leveling of fill. An edge is provided on theback side for grading when the machine is reversed.Long boomThe difference between a machine equipped withstandard boom or long boom is based on the selectionof buckets.Buckets and other attachments fit both standard- andlong boom versions.For further information regarding buckets and wearparts, see buckets for standard boom.L120EStatic tipping load, straight kg lbat full turn kg lbBreakout force kN lbfA Overall length mm ft inE Digging depth, max. dump mm inH Dump clerance mm ft inL Overall operating height mm ft inM Dump reach mm inN Reach at 45° discharge mm ft inOperating weight kg lb-2650-2360+5,4+500+30+520+520-30+430+180-5860-5210+1220+1'8''+0'1''+1'8''+1'8''-0'1''+1'5''+390AMN2135(7')EHL9
Wear partsBolt-on edge– For pre-drilled (PRD) straight edge and spade nosebuckets.– Provides base edge protection for longer service life.– Bolt-on cutting edges are reversible.– Maintains smooth bucket floor.Volvo Tooth SystemThe new Volvo Tooth System is designed for all types ofapplications, from handling easily broken bank materialsto breaking out hard and rocky materials.– Volvo Tooth System features different adapters andteeth to suit all applications.Segments between points– Provide longer base edge life of the bucket, up tofive times longer than edges without protectionbetween points.– Provide smooth clean floor.– Increase the adapter life by sharing bottom wear.– Protects the bucket base edge from scalloping.Note.Segments are recommended to be used incombination with 1 1/2 leg type adapters,but NEVER with flush mounted adapters.10
AdaptersFlush mounted adapterFlush mounted weld-on adapters are typically used inapplications where a clean bucket floor needs to bemaintained and the material is not extremely abrasive.The number of adapters is not restricted. This type ofadapter is most commonly used with general purposeteeth and is not to be used in combination with segments.Volvo Tooth SystemLA15FC35Note:Fits on all straight edge and spade nosebuckets.Should NOT be combined with segments.1 1/2 top leg adapter1 1/2 top leg adapters are weld-on adapters, which arewelded on both sides of the cutting edge for betterretention and protection. These adapters are generallycombined with segments and use abrasive resistantteeth.Volvo Tooth SystemLA15TL35Note:Fits on all straight edge and spade nosebuckets.Should NORMALLY be combined with segments.Bolt-on adapterBolt-on adapters have a 2-leg strap design and are usedon straight edge buckets. They provide good cuttingedge protection and are fairly quick and easy to replace.They are normally combined with segments to maintain aclean floor and prevent the cutting edge from scalloping.Volvo Tooth SystemLA15BN35Note:Fits on all straight edge predrilled buckets.Should NORMALLY be combined with segments.12
PointsAbrasive materialThe abrasive material extra tooth has a large surface on the wear shoe for good penetration capabilitiesand long service life. A slight undercut gives optimal bucket protection while the self-sharpening designpromotes long life.Volvo Tooth System15AMXLwith extra wear metalThe abrasive material tooth is used when extra penetration is required. A moderate undercut helps toprotect the bucket cutting edge while the self-sharpening design improves penetration and extends itsuseful life.Volvo Tooth System15AML13
Request for special attachmentsFor your special attachment needs, please fill in the special attachment inquiry form andsend it or fax it to:Volvo Wheel Loaders ABWheel Loader R&DDept: URSE- 633 85 Eskilstuna, SwedenTelefax: +46 16 152968You will also find this information on Violin and the Dealer Network. For viewing and downloading,please go to http://violin.vce.volvo.se/wlo/ – Product Information, Dealers Material,Attachment Catalogs or http://www.volvoce.com/.Every now and then the market has special requests for attachments with different dimensions,specifications, etc. Sometimes they may require attachments for specific applications.In these cases, Volvo Wheel Loaders is still the answer for your customer’s specialattachment needs. We not only have the knowledge and experience, but also we are theonly ones who can optimize attachments to work specifically with Volvo Wheel Loaders.Through the special attachment process, we can better evaluate your request to provideyou with a well-engineered solution, cost effective pricing, and shorter delivery times.14
Inquiry form for Customized Genuine AttachmentsVolvo Wheel Loaders(customize your attachment by filling out the form below)Wheel Loader model:URoff:SBLBStandard BoomLong BoomType of bucket:STE GP Straight Edge, General PurposeSTE RO Straight Edge, Rock ApplicationSPN Spade Nose BucketLM Light MaterialHIT Hi-Tip BucketOther type of attachment:Design:NormalFlat Floor BucketAttachment fitting type:HPHook-onPin-onBucket width*:mm*for future availbility regarding spare parts and cost reason,please try to use existing width’s from the attachment catalog.Bucket size:m3Material density:kg/m 3Material:Type of application:Requested wear parts:(if nothing else is said, std number of teeth is 8)VOLVO(Type: e.g. 30GPL)COMBI WEAR PARTS (Type: e.g. C4 T29)ESCO(Type: e.g. V33 TYL)Others:Welded Flush systemWelded 1 1/2 leg system +SEG (segment)Bolt-on (tooth) system + SEG (segment)BOE (Bolt-on Edge)Requested delivery date:Comments:Requested by:Telefax / e-mail:Country:Telephone:15
General purpose bucketsIntended for bolted options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.MN2135(7')H J LAT EScye vdbL110EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE P BOE**936462,62,12,72,9288014201470117028003515903.42.73.63.79'5"4'8"4'10"3'10"9'2"0'1.4"3510STE P T*SEG***936462,62,12,72,9288016201480137028003516703.42.73.63.79'5"5'4"4'10"4'6"9'2"0'1.4"3690STE P936462,52,02,62,8288013401440110028003513703.32.63.43.69'5"4'5"4'9"3'7"9'2"0'1.4"3030STE P BOE**801452,82,22,93,1288014101540117028003516403.72.93.84.09'5"4'8"5'0"3'10"9'2"0'1.4"3610STE P T*SEG***801452,82,22,93,1288016101540136028003517203.72.93.84.09'5"5'3"5'1"4'6"9'2"0'1.4"3800STE P801452,72,12,83,0288013401510109028003514203.52.73.73.99'5"4'5"4'11"3'7"9'2"0'1.4"3140A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment167770109029303720543010601660668325'6"3'7"9'7"12'2"17'10"3'6"5'5"660'3.3"7980127027903710543012101740669226'2"4'2"9'2"12'2"17'10"4'0"5'8"660'3.6"7670101030003740543010201660665625'2"3'4"9'10"12'3"17'10"3'4"5'5"660'2.2"7770108029303720551010601660668425'6"3'7"9'7"12'2"18'1"3'6"5'5"660'3.3"7970126027903710551012001730669226'2"4'2"9'2"12'2"18'1"3'11"5'8"660'3.6"7660100030003740552010201650665725'2"3'4"9'10"12'3"18'1"3'4"5'5"660'2.2"
General purpose bucketsBolt-on edge kit Order No. 93418Type of adapterBolt-onBolt-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82745LA15BN35Segment kit (set of 7)VolvoOrder No.93424Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLNote:* Corner adapters, part no. 11 417 164, are available from Volvo Parts.If using segments in conjunction with corner adapters, order outersegment part no. 11 156 372 for bucket width 2880 mm / 9'5".Type of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE P BOE**809392,92,33,03,2288014901530124028003516503.83.04.04.29'5"4'11"5'0"4'1"9'2"0'1.4"3630STE P T*SEG***809392,92,33,03,2288016901540144028003517303.83.04.04.29'5"5'6"5'1"4'9"9'2"0'1.4"3820STE P809392,82,22,93,128801410151011702800351430L110E3.72.93.84.09'5"4'8"4'11"3'10"9'2"0'1.4"3150STE P BOE**938763,12,53,33,4288015401570129028003517104.13.34.34.59'5"5'1"5'2"4'3"9'2"0'1.4"3770STE P T* SEG***938763,12,53,33,4288017401580149028003517904.13.34.34.59'5"5'8"5'2"4'11"9'2"0'1.4"3960STE P938763,02,43,23,3288014601550122028003514903.93.14.14.39'5"4'10"5'1"4'0"9'2"0'1.4"3290A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in785011502880371055001110169025'9"3'9"9'5"12'2"18'1"3'8"5'6"660'3.5"805013302740370055001260176026'5"4'4"9'0"12'2"18'1"4'1"5'9"660'3.8"25'5"3'6"9'8"12'3"18'1"3'6"5'6"660'2.4"* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment66896697774010702950374055001070168066627900120028403710555011501700669425'11"3'11"9'4"12'2"18'2"3'9"5'7"660'3.7"81101380270037005540129017706610326'7"4'6"8'10"12'2"18'2"4'3"5'10"660'4.1"78001120291037305550111017006625'7"3'8"9'7"12'3"18'2"3'8"5'7"660'2.6"17
General purpose bucketsIntended for bolted options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.Note: When using wide base tires, it is recommended touse 3000 mm / 9’10’ wide buckets in order to getfull coverage over the tires.MN2135(7')H J LAT EScye vdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment18STE P BOE**938823,42,73,63,7288015901630136028003517907980126027903700562012001730661004.43.54.74.99'5"5'3"5'4"4'6"9'2"0'1.4"395026'2"4'2"9'2"12'2"18'5"3'11"5'8"660'3.9"L110ESTE P T* SEG***938823,42,73,63,7288017901640156028003518808180144026503690561013401790661094.43.54.74.99'5"5'10"5'5"5'1"9'2"0'1.4"414026'10"4'9"8'8"12'1"18'5"4'5"5'10"660'4.3"STE P938823,32,63,53,628801510161012902800351580788011802860373056201160172066734.33.44.54.79'5"5'0"5'3"4'3"9'2"0'1.4"347025'10"3'11"9'5"12'3"18'5"3'10"5'8"660'2.9"
General purpose bucketsBolt-on edge kitOrder No. 93418Segment kit (set of 7)VolvoType of adapterBolt-on adapter kit (set of 8)Volvo Tooth SystemOrder No.93424Bolt-onOrder No.82745LA15BN35Intended for v = 2880 mm / 9'5"Bolt-on edge kitOrder No. 80577Intended for v = 2880 mm / 9'5"Note:* Corner adapters, part no. 11 417 164, are available from Volvo Parts.If using segments in conjunction with corner adapters, order outersegment part no. 11 156 372 for bucket width 2880 mm / 9'5".Segment kit (set of 7)VolvoOrder No.80578Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLIntended for v = 3000 mm / 9'10"Intended for v = 3000 mm / 9'10"Note:* Corner adapters, part no. 11 417 164, are available from Volvo Parts.If using segments in conjunction with corner adapters, order outersegment part no. 11 156 380 for bucket width 3000 mm / 9'10".Type of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE P BOE**823963,12,53,33,4300014901520124029203516804.13.34.34.59'10"4'11"5'0"4'1"9'7"0'1.4"3700STE P T* SEG***823963,12,53,33,4300016901530144029203516304.13.34.34.59'10"5'6"5'0"4'9"9'7"0'1.4"3590STE P823963,02,43,23,330001410150011702920351460L110E3.93.14.14.39'10"4'8"4'11"3'10"9'7"0'1.4"3220STE P BOE**808723,32,63,53,6300014501550120029103516804.33.44.54.79'10"4'9"5'1"3'11"9'7"0'1.4"3710STE P T*SEG***808723,42,73,63,7300017101640147029103517604.43.54.74.99'10"5'7"5'5"4'10"9'7"0'1.4"3880STE P808723,32,63,53,6300014401610119029103515904.33.44.54.79'10"4'9"5'3"3'11"9'7"0'1.4"3510A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in785011502880371054901110169025'9"3'9"9'5"12'2"18'0"3'8"5'7"660'3.5"805013302740370054901260176026'5"4'4"9'0"12'2"18'0"4'1"5'9"660'3.8"25'5"3'6"9'8"12'3"18'0"3'6"5'6"660'2.4"* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment6689669677501070295037405490107016806662772010802970380056301140176066225'4"3'6"9'9"12'6"18'6"3'9"5'9"660'.1"80801360272037005630128017606610026'6"4'5"8'11"12'2"18'6"4'2"5'9"660'4"7780110029203730563010901690666625'6"3'7"9'7"12'3"18'6"3'7"5'7"660'2.6"19
General purpose bucketsIntended for bolted options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.MN2135(7')H J LAT EScye vdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE H BOE**938692,62,12,72,9288012701470117028003515103.42.73.63.79'5"4'2"4'10"3'10"9'2"0'1.4"3330STE H T* SEG***938692,62,12,72,9288014701480137028003515903.42.73.63.79'5"4'10"4'10"4'6"9'2"0'1.4"3520STE H938692,52,02,62,828801190144011002800351290L110E3.32.63.43.69'5"3'11"4'9"3'7"9'2"0'1.4"2850STE H BOE**809412,92,33,03,2288013401530124028003515803.83.04.04.29'5"4'5"5'0"4'1"9'2"0'1.4"3480STE H T* SEG***809412,92,33,03,2288015401540144028003516603.83.04.04.29'5"5'0"5'1"4'9"9'2"0'1.4"3660STE H809412,82,22,93,1288012601510117028003513603.72.93.84.09'5"4'2"4'11"3'10"9'2"0'1.4"3000A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in7880119028503710549011401710668625'10"3'11"9'4"12'2"18'0"3'9"5'7"660'3.4"8090137027203710549012901770669426'6"4'6"8'11"12'2"18'0"4'3"5'10"660'3.7"7780111029203740549011001700665925'6"3'8"9'7"12'3"18'0"3'7"5'7"660'2.3"7950125028103710556011901730669126'1"4'1"9'2"12'2"18'3"3'11"5'8"660'3.6"81601430267037005560134017906610026'9"4'8"8'9"12'2"18'3"4'5"5'11"660'3.9"7850117028703740556011501730666425'9"3'10"9'5"12'3"18'3"3'9"5'8"660'2.5"* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment20
General purpose bucketsBolt-on edge kit Order No. 93418Type of adapterBolt-onBolt-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82745LA15BN35Segment kit (set of 7)VolvoOrder No.93424Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLNote:* Corner adapters, part no. 11 417 164, are available from Volvo Parts.If using segments in conjunction with corner adapters, order outersegment part no. 11 156 372 for bucket width 2880 mm / 9'5".Type of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft inSTE H BOE**938703,12,53,33,42880139015701290280035162080101300277037005610123017404.13.34.34.59'5"4'7"5'2"4'3"9'2"0'1.4"357026'3"4'3"9'1"12'2"18'5"4'0"5'9"660'3.8"4.1 3,03.3 2,44.3 3,24.5 3,39'5" 28805'3" 13205'2" 15504'11" 12209'2" 28000'1.4" 353750 140027'0"4'10"8'8"12'1"18'5"4'6"5'11"66 660'4.1" 70* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment6696STE H T* SEG***938703,12,53,33,428801590158014902800351700822014802630370056101380180066105STE H938707910122028403730561011901740L110E3.93.14.14.39'5"4'4"5'1"4'0"9'2"0'1.4"309026'0"4'0"9'4"12'3"18'5"3'11"5'9"660'2.7"STE H BOE**938723,42,73,63,7288014601620136028003516908090136027203700567012801760661024.43.54.74.99'5"4'9"5'4"4'6"9'2"0'1.4"373026'6"4'6"8'11"12'2"18'7"4'2"5'9"660'4"STE H T*SEG***938723,42,73,63,7288016601630156028003517808290154025803690567014201820661114.43.54.74.99'5"5'5"5'4"5'1"9'2"0'1.4"392027'2"5'1"8'6"12'1"18'7"4'8"6'0"660'4.4"STE H938723,32,63,53,628801390160012902800351480799012802790373056701240176066754.33.44.54.79'5"4'7"5'3"4'3"9'2"0'1.4"325026'2"4'3"9'2"12'3"18'7"4'1"5'9"660'3"21
General purpose bucketsIntended for bolted options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.Note: When using wide base tires, it is recommended touse 3000 mm / 9’10’ wide buckets in order to getfull coverage over the tires.MN2135(7')H J LAT EScye vdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment22STE H BOE**823973,12,53,33,430001340152012402920351610795012502810371055501190173066914.13.34.34.59'10"4'5"5'0"4'1"9'7"0'1.4"355026'1"4'1"9'2"12'2"18'3"3'11"5'8"660'3.6"STE H T* SEG***823973,12,53,33,430001540153014402920351560816014302670370055501340179066994.13.34.34.59'10"5'0"5'0"4'9"9'7"0'1.4"344026'9"4'8"8'9"12'2"18'3"4'5"5'11"660'3.9"STE H823973,02,43,23,33000126015001170292035139078501170287037405550115017306664L110E3.93.14.14.39'10"4'2"4'11"3'10"9'7"0'1.4"306025'9"3'10"9'5"12'3"18'3"3'9"5'8"660'2.5"STE H BOE**805753,42,73,63,730001370163012702920351690799012802780371056901210174066954.43.54.74.99'10"4'6"5'4"4'2"9'7"0'1.4"372026'2"4'2"9'2"12'2"18'8"4'0"5'8"660'3.7"STE H T*SEG***805753,42,73,63,7300015601640147029203516308190146026503700569013601800661024.43.54.74.99'10"5'2"5'4"4'10"9'7"0'1.4"360026'10"4'9"8'8"12'2"18'8"4'5"5'11"660'4"STE H805753,32,63,53,630001290161011902920351460789012002850373056901170174066684.33.44.54.79'10"4'3"5'3"3'11"9'7"0'1.4"323025'10"3'11"9'4"12'3"18'8"3'10"5'8"660'2.7"
General purpose bucketsBolt-on edge kit Order No. 80577Type of adapterBolt-onBolt-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82745LA15BN35Segment kit (set of 7)VolvoOrder No.80578Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLNote:* Corner adapters, part no. 11 417 164, are available from Volvo Parts.If using segments in conjunction with corner adapters, order outersegment part no. 11 156 380 for bucket width 3000 mm / 9'10".23
Flat floor bucketsIntended for bolted options onlyThe buckets are intended for earth moving, overburdenclearing, landscaping, etc, and are ideal for use in softground conditions.MN2135(7')H J LAT EScyevdbdbL110EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE P BOE* FF821173,12,53,33,4288014801560126028003518104.13.34.34.59'5"4'10"5'1"4'2"9'2"0'1.4"3990STE P FF821173,02,43,23,3288014101540119028003515903.93.14.14.39'5"4'7"5'1"3'11"9'2"0'1.4"3510STE H BOE* FF823603,12,53,33,4288013701570126028003517404.13.34.34.59'5"4'6"5'2"4'2"9'2"0'1.4"3830STE H FF823603,02,43,23,3288012901540119028003515203.93.14.14.39'5"4'3"5'1"3'11"9'2"0'1.4"3350A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* BOE = Bolt-on edge78801180279037005530103015606110225'10"3'10"9'2"12'2"18'2"3'5"5'1"610'4"7780110028603730553010001560617525'6"3'7"9'5"12'3"18'2"3'3"5'1"610'3"80001290270037005600111015906110426'3"4'3"8'10"12'2"18'4"3'8"5'3"610'4.17900121027803720560010701600617825'11"3'11"9'1"12'3"18'4"3'6"5'3"610'3.1"24
Flat floor bucketsBolt-on edge kit Order No. 9341825
General purpose bucketsIntended for welded teeth options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.Focus on penetration.Note: When using wide base tires, it is recommended touse 3000 mm / 9'10" wide buckets in order to getfull coverage over the tires.MN2135(7')H J LAT ESce vSTE P T*ydbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* Dimensions based on 15AML points. Other points may affect dimensions differently.** SEG = Segment26STE P T* SEG**938813,12,53,33,4288017301580149028003517808100137027103700554012901770661034.13.34.34.59'5"5'8"5'2"4'11"9'2"0'1.4"393026'7"4'6"8'11"12'2"18'2"4'3"5'10"660'4"STE P T*938813,02,43,23,328801730156014802800351630808013602730372055501300179066793.93.14.14.39'5"5'8"5'1"4'10"9'2"0'1.4"358026'6"4'6"8'11"12'2"18'2"4'3"5'11"660'3.1"L110ESTE P T* SEG**938833,42,73,63,7288018001640156028003518608180144026603690561013401790661084.43.54.74.99'5"5'11"5'5"5'1"9'2"0'1.4"411026'10"4'9"8'9"12'1"18'5"4'5"5'10"660'4.3"938833,32,63,53,628801800162015502800351710815014202680372056201350181066854.33.44.54.79'5"5'11"5'4"5'1"9'2"0'1.4"377026'9"4'8"8'9"12'2"18'5"4'5"5'11"660'3.3"
General purpose bucketsSegment kit (set of 7)Type of adapterWeld-on adapter kit (set of 8)VolvoOrder No.934241 1/2 LegVolvo Tooth SystemOrder No.82744LA15TL35Intended for v = 2880 mm / 9'5"Segment kit (set of 7)VolvoOrder No.80578Intended for v = 3000 mm / 9'10"FlushType of pointAMOrder No.8274615AMXLVolvo Tooth SystemOrder No.82743LA15FC35Point kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLL110EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE P T* SEG**825903,42,73,63,7300017101640146029103517504.43.54.74.99'10"5'7"5'5"4'10"9'7"0'1.4"3850STE P T*825903,32,63,53,6300017101620146029103517204.33.44.54.79'10"5'7"5'4"4'10"9'7"0'1.4"3800A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in80801350272037005630127017606610026'6"4'5"8'11"12'2"18'6"4'2"5'9"660'3.9"805013402740372056301290179026'5"4'5"9'0"12'3"18'6"4'3"5'10"660'3.1"* Dimensions based on 15AML points. Other points may affect dimensions differently.** SEG = Segment667827
General purpose bucketsIntended for welded teeth options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.Focus on penetration.MN2135(7')H J LAT EScye vdbL110EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE H T* SEG**938713,12,53,33,4288015801580149028003516904.13.34.34.59'5"5'2"5'2"4'11"9'2"0'1.4"3720STE H T*938713,02,43,23,3288015801560149028003515303.93.14.14.39'5"5'2"5'1"4'10"9'2"0'1.4"3380STE H T* SEG**938733,42,73,63,7288016501630156028003517604.43.54.74.99'5"5'5"5'4"5'1"9'2"0'1.4"3890STE H T*938733,32,63,53,6288016501610155028003516104.33.44.54.79'5"5'5"5'3"5'1"9'2"0'1.4"3550A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in82101480263037005610137018006610526'11"4'10"8'8"12'1"18'5"4'6"5'11"660'4.1"8190146026503720561013801830668226'10"4'10"8'8"12'2"18'5"4'7"6'0"660'3.2"82901540258036905670142018206611127'2"5'1"8'6"12'1"18'7"4'8"6'0"660'4.4"8260153026003710567014301840668727'1"5'0"8'7"12'2"18'7"4'8"6'1"660'3.4"* Dimensions based on 15AML points. Other points may affect dimensions differently.** SEG = Segments28
General purpose bucketsSegment kit (set of 7)Type of adapterWeld-on adapter kit (set of 8)VolvoOrder No.934241 1/2 LegVolvo Tooth SystemOrder No.82744LA15TL35FlushVolvo Tooth SystemOrder No.82743LA15FC35Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AML29
Flat floor bucketsIntended for welded teeth options onlyThe buckets are intended for earth moving, overburdenclearing, landscaping, etc, and are ideal for use in softground conditions.MN2135(7')H J LAT EScyevdbdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in30STE P T* FF821183,02,43,23,328801670155014502800351730806013402670371055301180163061873.93.14.14.39'5"5'6"5'1"4'9"9'2"0'1.4"380026'5"4'5"8'9"12'2"18'2"3'10"5'4"610'3.4"STE P FF821183,02,43,23,32880141015401190280035160077801100286037305530100015603.93.14.14.39'5"4'7"5'1"3'11"9'2"0'1.4"352025'6"3'7"9'5"12'3"18'2"3'3"5'1"610'3"L110E** Dimensions based on 15AMXL points. Other points may affect dimensions differently.6175STE H T* FF823613,02,43,23,328801560155014502800351650818014502580371056001250165061903.93.14.14.39'5"5'1"5'1"4'9"9'2"0'1.4"364026'10"4'9"8'5"12'2"18'4"4'1"5'5"610'3.5"STE H FF823613,02,43,23,328801290154011902800351520790012102780372056001070160061783.93.14.14.39'5"4'3"5'1"3'11"9'2"0'1.4"336025'11"3'11"9'1"12'3"18'5"3'6"5'3"610'3.1"
Flat floor bucketsType of adapterFlushWeld-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82743LA15FC35Type of pointAMPoint kit (set of 8)Volvo Tooth SystemOrder No.8274615AMXL31
Rock bucketsIntended for welded teeth options onlyThe buckets are designed for loading material thatrequire high penetration and breakout forces.The buckets have low-cut sides to facilitate penetrationinto the material.MNLH J2135(7')AT EScyevdbL110EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSPN P BOE**938892,72,22,83,0288016801540144028403520103.52.93.73.99'5"5'6"5'1"4'8"9'4"0'1.4"4420SPN P T* SEG***938892,72,22,83,0288018701550163028403520903.52.93.73.99'5"6'2"5'1"5'4"9'4"0'1.4"4600SPN P T*938892,62,12,72,9288018701550163028403519503.42.73.63.79'5"6'2"5'1"5'4"9'4"0'1.4"4290SPN P938892,62,12,72,9288016001520136028403518103.42.73.63.79'5"5'3"5'0"4'6"9'4"0'1.4"3990A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in328100136027203720555012701760667626'7"4'5"8'11"12'2"18'3"4'2"5'9"27'3"5'0"8'6"12'2"18'3"4'8"5'12"660'3.3"* Dimensions based on L5 tires and 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment660'3"830015302590372055501410182066858300153025903720555014101820668427'3"5'0"8'6"12'2"18'3"4'8"5'12"660'3.3"8000128027903750555012301760665026'3"4'2"9'2"12'4"18'3"4'0"5'9"660'2"
Rock bucketsBolt-on edge kit Order No. 93419Type of adapter1 1/2 LegWeld-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82744LA15TL35Segment kit (set of 7)VolvoOrder No.93899FlushType of pointAMOrder No.8274615AMXLVolvo Tooth SystemOrder No.82743LA15FC35Point kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLL110EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSPN P BOE**938903,02,43,23,3288017501580150028403519103.93.14.14.39'5"5'9"5'2"4'11"9'4"0'1.4"4220SPN P T* SEG***938903,02,43,23,3288019401590170028403519903.93.14.14.39'5"6'4"5'3"5'7"9'4"0'1.4"4400SPN P T*938902,92,33,03,2288019401590170028403518503.83.04.04.29'5"6'4"5'3"5'7"9'4"0'1.4"4080SPN P938902,92,33,03,2288016701560143028403517203.83.04.04.29'5"5'6"5'1"4'8"9'4"0'1.4"3790A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in8080135027403740563012801780665626'6"4'5"9'0"12'3"18'6"4'3"5'10"660'2.2"828015202610373056301430184027'2"5'0"8'7"12'3"18'6"4'8"6'0"660'2.6"* Dimensions based on L5 tires and 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment66658280152026103740563014301840666427'2"5'0"8'7"12'3"18'6"4'8"6'0"660'2.5"8010131027703730559012701780666926'4"4'3"9'1"12'3"18'4"4'2"5'10"660'2.7"33
Rock bucketsIntended for welded teeth options onlyThe buckets are designed for loading material thatrequire high penetration and breakout forces.The buckets have low-cut sides to facilitate penetrationinto the material.MNLH J2135(7')AT EScyevdbL110EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSPN H BOE**938883,02,43,23,3288016001580150028403518203.93.14.14.39'5"5'3"5'2"4'11"9'4"0'1.4"4000SPN H T* SEG***938883,02,43,23,3288017901590170028403519003.93.14.14.39'5"5'11"5'3"5'7"9'4"0'1.4"4180SPN H T*938882,92,33,03,2288017901590170028403517503.83.04.04.29'5"5'11"5'3"5'7"9'4"0'1.4"3870SPN H938882,92,33,03,2288015301560143028403516203.83.04.04.29'5"5'0"5'1"4'8"9'4"0'1.4"3570A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestS lifting arm pos. °T Digging depth mm ft in348190145026703740569013601820665826'10"4'9"8'9"12'3"18'8"4'6"6'0"660'2.3"839016202540373056901510187027'6"5'4"8'4"12'3"18'8"4'11"6'2"660'2.7"* Dimensions based on L5 tires and 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment66678390162025403730569015101870666627'6"5'4"8'4"12'3"18'8"4'11"6'2"660'2.6"8090137027403770569013201820663226'6"4'6"9'0"12'4"18'8"4'4"6'0"660'1.3"
Rock bucketsBolt-on edge kit Order No. 93419Type of adapter1 1/2 LegWeld-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82744LA15TL35Segment kit (set of 7)VolvoOrder No.93899FlushType of pointAMOrder No.8274615AMXLVolvo Tooth SystemOrder No.82743LA15FC35Point kit (set of 8)Volvo Tooth SystemOrder No.8274215AML35
Rock bucketsIntended for welded teeth options onlyThe buckets are designed for loading material thatrequire high penetration and breakout forces.The buckets have low-cut sides to facilitate penetrationinto the material.MNLH J2135(7')AT EScyevdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE RO P T* SEG**938873,12,53,33,4288017301590148028003520604.13.34.34.59'5"5'8"5'3"4'10"9'2"0'1.4"4540L110ESTE RO P T*938873,02,43,23,3288017301590148028003519103.93.14.14.39'5"5'8"5'3"4'10"9'2"0'1.4"4210A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* Dimensions based on L5 tires and 15AML points. Other points may affectdimensions differently.** SEG = Segment368070134027403730563012701770666626'6"4'5"9'0"12'3"18'6"4'2"5'10"660'2.6"8070134027403740563012701770666526'6"4'5"9'0"12'3"18' 6"4'2"5'10"660'2.5"
Rock bucketsSegment kit (set of 7)VolvoOrder No.93424Type of adapter1 1/2 LegWeld-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82744LA15TL35FlushVolvo Tooth SystemOrder No.82743LA15FC35Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AML37
General purpose bucketIntended for bolted options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.MN2135(7')H J LAT ESce vSTE P BOE**ydbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment38936462,62,12,72,928801420147011702800351590787011002990378055001100175067913.42.73.63.79'5"4'8"4'10"3'10"9'2"0'1.4"351025'10"3'7"9'10"12'5"18'0"3'7"5'9"670'3.6"STE P T*SEG***936462,62,12,72,9288016201480137028003516708080128028603780549012401820671003.42.73.63.79'5"5'4"4'10"4'6"9'2"0'1.4"369026'6"4'3"9'4"12'5"18'0"4'1"6'0"670'3.9"STE P936462,52,02,62,82880134014401100280035137077701020306038105500106017406764L120E3.32.63.43.69'5"4'5"4'9"3'7"9'2"0'1.4"303025'6"3'4"10'1"12'6"18'0"3'6"5'9"670'2.5"STE P BOE**801452,82,22,93,128801410154011702800351640787011002990378055801090175067913.72.93.84.09'5"4'8"5'0"3'10"9'2"0'1.4"361025'10"3'7"9'10"12'5"18'4"3'7"5'9"670'3.6"STE P T*SEG***801452,82,22,93,1288016101540136028003517208070128028603770558012401820671003.72.93.84.09'5"5'3"5'1"4'6"9'2"0'1.4"380026'6"4'2"9'5"12'5"18'4"4'1"6'0"670'3.9"STE P801452,72,12,83,028801340151010902800351420777010203060381055801050174067643.52.73.73.99'5"4'5"4'11"3'7"9'2"0'1.4"314025'6"3'4"10'1"12'6"18'4"3'5"5'8"670'2.5"
General purpose bucketBolt-on edge kit Order No. 93418Type of adapterBolt-onBolt-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82745LA15BN35Segment kit (set of 7)VolvoOrder No.93424Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLNote:* Corner adapters, part no. 11 417 164, are available from Volvo Parts.If using segments in conjunction with corner adapters, order outersegment part no. 11 156 372 for bucket width 2880 mm / 9'5".Type of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft incBucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft inSTE P BOE**809392,92,33,03,22880149015301240280035165079501170294037805570115017703.83.04.04.29'5"4'11"5'0"4'1"9'2"0'1.4"363026'1"3'10"9'8"12'5"18'3"3'9"5'10"670'3.8"STE P T*SEG***809392,92,33,03,2288016901540144028003517308150135028103770557012901850671053.83.04.04.29'5"5'6"5'1"4'9"9'2"0'1.4"382026'9"4'5"9'2"12'4"18'3"4'3"6'1"670'4.1"STE P809392,82,22,93,128801410151011702800351430785010903010381055701110177067693.72.93.84.09'5"4'8"4'11"3'10"9'2"0'1.4"315025'9"3'7"9'11"12'6"18'3"3'8"5'10"670'2.7"* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment6796L120ESTE P BOE**938763,12,53,33,4288015401570129028003517108000122029003770561011801790671024.13.34.34.59'5"5'1"5'2"4'3"9'2"0'1.4"377026'3"4'0"9'6"12'5"18'5"3'11"5'10"670'4"STE P T* SEG***938763,12,53,33,4288017401580149028003517908210140027703760561013301860671114.13.34.34.59'5"5'8"5'2"4'11"9'2"0'1.4"396026'11"4'7"9'1"12'4"18'5"4'4"6'1"670'4.4"STE P938763,02,43,23,328801460155012202800351490790011402970380056101140179067753.93.14.14.39'5"4'10"5'1"4'0"9'2"0'1.4"329025'11"3'9"9'9"12'6"18'5"3'9"5'10"670'3"39
General purpose bucketIntended for bolted options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.Note: When using wide base tires, it is recommended touse 3000 mm / 9’10’ wide buckets in order to getfull coverage over the tires.MN2135(7')H J LAT EScye vdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft incBucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment40STE P BOE**823963,12,53,33,430001490152012402920351680795011702940378055601150177067974.13.34.34.59'10"4'11"5'0"4'1"9'7"0'1.4"370026'1"3'10"9'8"12'5"18'3"3'9"5'10"670'3.8"STE P T* SEG***823963,12,53,33,4300016901530144029203516308150135028103770556012901850671044.13.34.34.59'10"5'6"5'0"4'9"9'7"0'1.4"359026'9"4'5"9'2"12'4"18'3"4'3"6'1"670'4.1"STE P823963,02,43,23,330001410150011702920351460785010903010381055601110177067703.93.14.14.39'10"4'8"4'11"3'10"9'7"0'1.4"322025'9"3'7"9'11"12'6"18'3"3'8"5'10"670'2.7"L120ESTE P BOE**808723,42,73,63,7300015201640127029103518107980120029203770569011701780671014.43.54.74.99'10"5'0"5'4"4'2"9'7"0'1.4"400026'2"3'11"9'7"12'5"18'8"3'10"5'10"670'4"STE P T*SEG***808723,42,73,63,7300017101640147029103517608180138027803770569013101850671084.43.54.74.99'10"5'7"5'5"4'10"9'7"0'1.4"388026'10"4'6"9'2"12'4"18'8"4'4"6'1"670'4.3"STE P808723,32,63,53,630001440161011902910351590788011202990380056901130178067744.33.44.54.79'10"4'9"5'3"3'11"9'7"0'1.4"351025'10"3'8"9'10"12'6"18'8"3'8"5'10"670'2.9"
General purpose bucketBolt-on edge kit Order No. 80577Type of adapterBolt-onBolt-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82745LA15BN35Segment kit (set of 7)VolvoOrder No.80578Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLNote:* Corner adapters, part no. 11 417 164, are available from Volvo Parts.If using segments in conjunction with corner adapters, order outersegment part no. 11 156 380 for bucket width 3000 mm / 9'10".L120EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft incBucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE P BOE**820243,62,93,84,0300015501670131029203518004.73.84.95.29'10"5'1"5'6"4'3"9'7"0'1.4"3970STE P T* SEG***820243,62,93,84,0300017501680151029203517504.73.84.95.29'10"5'9"5'6"4'11"9'7"0'1.4"3860STE P820243,52,73,73,9300014801650123029203515804.63.54.85.09'10"4'10"5'5"4'1"9'7"0'1.4"3480A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in80201230289037705740119018006710326'4"4'1"9'6"12'4"18'10"3'11"5'11"670'4.1"82201410276037605740134018606711127'0"4'8"9'1"12'4"18'10"4'5"6'1"670'4.4"7920115029603800575011501790* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment677726'0"3'9"9'9"12'6"18'10"3'9"5'10"670'3"41
General purpose bucketIntended for bolted options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.MN2135(7')H J LAT EScye vdbdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft incBucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in42STE P BOE**938823,42,73,63,7288015901630136028003517908080128028503770568012301810671074.43.54.74.99'5"5'3"5'4"4'6"9'2"0'1.4"395026'6"4'2"9'4"12'4"18'8"4'1"5'11"670'4.2"STE P T* SEG***938823,32,63,53,6288017901640156028003517308280146027203760568013801880671154.33.44.54.79'5"5'10"5'5"5'1"9'2"0'1.4"380027'2"4'10"8'11"12'4"18'8"4'6"6'2"670'4.5"STE P938823,32,63,53,6288015101610129028003515807980120029203790568011901810L120E4.33.44.54.79'5"5'0"5'3"4'3"9'2"0'1.4"347026'2"3'11"9'7"12'5"18'8"3'11"5'11"670'3.2"* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment6781STE P BOE**938843,62,93,84,0288016501670141028003518408130132028203760573012601830671124.73.84.95.29'5"5'5"5'6"4'7"9'2"0'1.4"406026'8"4'4"9'3"12'4"18'9"4'2"6'0"670'4.4"STE P T*SEG***938843,62,93,84,0288018501680161028003519308330150026803750573014101890671214.73.84.95.29'5"6'1"5'6"5'3"9'2"0'1.4"425027'4"4'11"8'10"12'4"18'9"4'7"6'2"670'4.7"STE P938843,52,83,73,928801580165013302800351630803012402890379057301220182067854.63.74.85.09'5"5'2"5'5"4'4"9'2"0' 1.4"358026'4"4'1"9'6"12'5"18'10"4'0"6'0"670'3.3"
General purpose bucketBolt-on edge kit Order No. 93418Type of adapterBolt-onBolt-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82745LA15BN35Segment kit (set of 7)VolvoOrder No.93424Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLNote:* Corner adapters, part No. 11 417 164, are available from Volvo Parts.If using segments in conjunction with corner adapters, order outersegment Part No. 11 156 372 for bucket width 2880 mm / 9'5".Type of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft incBucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE H BOE**938692,62,12,72,9288012701470117028003515103.42.73.63.79'5"4'2"4'10"3'10"9'2"0'1.4"3330STE H T* SEG***938692,62,12,72,9288014701480137028003515903.42.73.63.79'5"4'10"4'10"4'6"9'2"0'1.4"3520STE H938692,52,02,62,8288011901440110028003512903.32.63.43.69'5"3'11"4'9"3'7"9'2"0'1.4"2850L120ESTE H BOE**809412,92,33,03,2288013401530124028003515803.83.04.04.29'5"4'5"5'0"4'1"9'2"0'1.4"3480STE H T* SEG***809412,92,33,03,2288015401540144028003516603.83.04.04.29'5"5'0"5'1"4'9"9'2"0'1.4"3660STE H809412,82,22,93,1288012601510117028003513603.72.93.84.09'5"4'2"4'11"3'10"9'2"0'1.4"3000A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in798012002920378055601180179026'2"3'11"9'7"12'5"18'3"3'10"5'11"670'3.7"26'10"4'7"9'2"12'4"18'3"4'4"6'1"670'4"25'10"3'8"9'10"12'6"18'3"3'9"5'10"670'2.6"* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment6793819013902780377055601320186067102788011202990381055601140179067668050127028703780563012301820679926'5"4'2"9'5"12'5"18'6"4'0"6'0"670'3.9"82601450273037705630137018806710727'1"4'9"9'0"12'4"18'6"4'6"6'2"670'4.2"7960119029403800563011901810677226'1"3'11"9'8"12'6"18'6"3'11"5'11"670'2.8"43
General purpose bucketIntended for bolted options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.MN2135(7')H J LAT EScye vdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft incBucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE H BOE**938703,12,53,33,4288013901570129028003516204.13.34.34.59'5"4'7"5'2"4'3"9'2"0'1.4"3570STE H T* SEG***938703,12,53,33,4288015901580149028003517004.13.34.34.59'5"5'3"5'2"4'11"9'2"0'1.4"3750STE H938703,02,43,23,328801320155012202800351400L120E3.93.14.14.39'5"4'4"5'1"4'0"9'2"0'1.4"3090STE H BOE**938723,42,73,63,7288014601620136028003516904.43.54.74.99'5"4'9"5'4"4'6"9'2"0'1.4"3730STE H T*SEG***938723,42,73,63,7288016601630156028003517804.43.54.74.99'5"5'5"5'4"5'1"9'2"0'1.4"3920STE H938723,32,63,53,6288013901600129028003514804.33.44.54.79'5"4'7"5'3"4'3"9'2"0'1.4"3250A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in4481101320283037705670127018306710426'7"4'4"9'3"12'4"18'7"4'2"6'0"670'4.1"83201500269037605670141019006711327'4"4'11"8'10"12'4"18'7"4'8"6'3"670'4.4"801012402900380056801230183026'4"4'1"9'6"12'6"18'7"4'0"6'0"670'3"* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment677781901380278037705740131018506711026'10"4'6"9'1"12'4"18'10"4'4"6'1"670'4.3"83901560265037605740146019106711827'6"5'2"8'8"12'4"18'10"4'9"6'3"670'4.7"8090130028503790574012701850678326'6"4'3"9'4"12'5"18'10"4'2"6'1"670'3.3"
General purpose bucketBolt-on edge kit Order No. 93418Type of adapterBolt-onBolt-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82745LA15BN35Segment kit (set of 7)VolvoOrder No.93424Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLNote:* Corner adapters, part no. 11 417 164, are available from Volvo Parts.If using segments in conjunction with corner adapters, order outersegment part no. 11 156 372 for bucket width 2880 mm / 9'5".Type of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft incBucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft inSTE H BOE**938753,62,93,84,0288015101690141028003517408240143027503760579013501870671144.73.84.95.29'5"4'11"5'7"4'7"9'2"0'1.4"383027'0"4'8"9'0"12'4"19'0"4'5"6'1"670'4.5"L120ESTE H T* SEG***938753,62,93,84,0288017001700161028003518208440161026103750579014901920671234.73.84.95.29'5"5'7"5'7"5'3"9'2"0'1.4"402027'8"5'3"8'7"12'4"19'0"4'11"6'4"670'4.8"STE H938753,52,83,73,9288014301670133028003515208140135028203790579013101870* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment67874.63.74.85.09'5"4'8"5'6"4'4"9'2"0'1.4"335026'8"4'5"9'3"12'5"19'0"4'3"6'1"670'3.4"45
General purpose bucketIntended for bolted options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.Note: When using wide base tires, it is recommended touse 3000 mm / 9’10’ wide buckets in order to getfull coverage over the tires.MN2135(7')H J LAT EScye vdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft incBucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment46STE H BOE**823973,12,53,33,430001340152012402920351610805012702870378056201230182067994.13.34.34.59'10"4'5"5'0"4'1"9'7"0'1.4"355026'5"4'2"9'5"12'5"18'5"4'0"6'0"670'3.9"STE H T* SEG***823973,12,53,33,4300015401530144029203515608260145027303770562013701880671074.13.34.34.59'10"5'0"5'0"4'9"9'7"0'1.4"344027'1"4'9"9'0"12'4"18'5"4'6"6'2"670'4.2"STE H823973,02,43,23,330001260150011702920351390796011902940380056201190181067723.93.14.14.39'10"4'2"4'11"3'10"9'7"0'1.4"306026'1"3'11"9'8"12'6"18'5"3'11"5'11"670'2.8"L120ESTE H BOE**805753,42,73,63,7300013701630127029203516908090130028503770576012501820671034.43.54.74.94'6"4'6"5'4"4'2"9'7"0'1.4"372026'6"4'3"9'4"12'5"18'11"4'1"6'0"670'4"STE H T*SEG***805753,42,73,63,7300015601640147029203516308290148027103760576013901890671104.43.54.74.99'10"5'2"5'4"4'10"9'7"0'1.4"360027'2"4'10"8'11"12'4"18'11"4'7"6'2"670'4.3"STE H805753,32,63,53,630001290161011902920351460799012202920380057601210182067764.33.44.54.79'10"4'3"5'3"3'11"9'7"0'1.4"323026'2"4'0"9'7"12'6"18'11"4'0"6'0"670'3"
General purpose bucketBolt-on edge kit Order No. 80577Type of adapterBolt-onBolt-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82745LA15BN35Segment kit (set of 7)VolvoOrder No.80578Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLNote:* Corner adapters, part no. 11 417 164, are available from Volvo Parts.If using segments in conjunction with corner adapters, order outersegment part no. 11 156 380 for bucket width 3000 mm / 9'10".Type of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft incBucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft inSTE H BOE**826023,62,93,84,0300014101680131029203517708130133028203770581012801840671064.73.84.95.29'10"4'7"5'6"4'3"9'7"0'1.4"389026'8"4'5"9'3"12'4"19'1"4'2"6'0"670'4.2"L120ESTE H T* SEG***826023,62,93,84,0300016001690151029203517108330151026803760581014201900671144.73.84.95.29'10"5'3"5'6"4'11"9'7"0'1.4"378027' 4"5'0"8'10"12'4"19'1"4'8"6'3"670'4.5"STE H826023,52,73,73,9300013301650123029203515408030125028903800581012401830* Dimensions based on 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment67794.63.54.85.09'10"4'4"5'5"4'1"9'7"0'1.4"340026'4"4'1"9'6"12'5"19'1"4'1"6'0"670'3.1"47
Flat floor bucketsIntended for bolted options onlyThe buckets are intended for earth moving, overburdenclearing, landscaping, etc, and are ideal for use in softground conditions.MN2135(7')H J LAT EScyevdbdbL120EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft incBucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE P BOE* FF821173,12,53,33,4288014801560126028003518104.13.34.34.59'5"4'10"5'1"4'2"9'2"0'1.4"3990STE P FF821173,02,43,23,3288014101540119028003515903.93.14.14.39'5"4'7"5'1"3'11"9'2"0'1.4"3510STE P BOE* FF826083,52,83,73,9288016201640141028003519904.63.74.85.09'5"5'4"5'4"4'8"9'2"0'1.4"4380STE P FF826083,42,73,63,7288015401610134028003517704.43.54.74.99'5"5'1"5'3"4'5"9'2"0'1.4"3900A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge, Pos. G mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in79801200286037705600108016406210926'2"3'11"9'5"12'4"18'4"3'6"5'5"620'4.3"7880112029303790560010401640628225'10"3'8"9'7"12'5"18'4"3'5"5'5"620'3.2"80501260281037705700114016706210026'5"4'2"9'3"12'5"18'8"3'9"5'6"620'4"7950118028803800570011001680627326'1"3'11"9'6"12'6"18'8"3'7"5'6"620'2.9"* BOE = Bolt-on edge48
Flat floor bucketsBolt-on edge kit Order No. 93418L120EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE H BOE* FF823603,12,53,33,4288013701570126028003517404.13.34.34.59'5"4'6"5'2"4'2"9'2"0'1.4"3830STE H FF823603,02,43,23,3288012901540119028003515203.93.14.14.39'5"4'3"5'1"3'11"9'2"0'1.4"3350STE H BOE* FF825953,52,83,73,9288014401640134028003518304.63.74.85.09'5"4'9"5'4"4'5"9'2"0'1.4"4040STE H FF825953,42,73,63,7288013701610126028003516104.43.54.74.99'5"4'6"5'3"4'2"9'2"0'1.4"3560A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge, Pos. G mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* BOE = Bolt-on edge81001300277037605670115016706311226'7"4'3"9'1"12'4"18'7"3'9"5'6"630'4.4"8000122028503790567011201680638526'3"4'0"9'4"12'5"18'7"3'8"5'6"630'3.4"81601360273037705760121017006310226'9"4'6"8'11"12'5"18'11"4'0"5'7"630'4"8060128028003800576011701710637526'5"4'3"9'2"12'6"18'11"3'10"5'7"630'3"49
General purpose bucketsIntended for welded teeth options onlyThe buckets are designed for loading loose material ormaterial that is easily broken out of the bank.Focus on penetration.Note: When using wide base tires, it is recommended touse 3000 mm / 9'10" wide buckets in order to getfull coverage over the tires.MN2135(7')H J LAT EScye vdbdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE P T* SEG**938813,12,53,33,4288017301580149028003517804.13.34.34.59'5"5'8"5'2"4'11"9'2"0'1.4"3930STE P T*938813,02,43,23,3288017301560148028003516303.93.14.14.39'5"5'8"5'1"4'10"9'2"0'1.4"3580STE P T* SEG**938833,42,73,63,728801800164015602800351860L120E4.43.54.74.99'5"5'11"5'5"5'1"9'2"0'1.4"4110STE P T*938833,32,63,53,6288018001620155028003517104.33.44.54.79'5"5'11"5'4"5'1"9'2"0'1.4"3770STE P T* SEG**825903,42,73,63,7300017101640146029103517504.43.54.74.99'10"5'7"5'5"4'10"9'7"0'1.4"3850STE P T*825903,32,63,53,6300017101620146029103517204.33.44.54.79'10"5'7"5'4"4'10"9'7"0'1.4"3800A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge, Pos. G mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in82001390277037605610133018606711026'11"4'7"9'1"12'4"18'5"4'4"6'1"670'4.3"818013802790379056101340188026'10"4'6"9'2"12'5"18'5"4'5"6'2"670'3.4"82801460272037605680137018806711627'2"4'9"8'11"12'4"18'8"4'6"6'2"670'4.6"* Dimensions based on 15AML points. Other points may affect dimensions differently.** SEG = Segment67878260145027403780568013901900679327'1"4'9"9'0"12'5"18'8"4'7"6'3"670'3.7"81801370279037705690131018506710826'10"4'6"9'2"12'4"18'8"4'4"6'1"670'4.3"8160136028103790569013201870678626'9"4'6"9'2"12'5"18'8"4'4"6'2"670'3.4"50
General purpose bucketsSegment kit (set of 7)VolvoOrder No.93424Type of adapter1 1/2 LegWeld-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82744LA15TL35Intended for v = 2880 mm / 9'5"Segment kit (set of 7)VolvoOrder No.80578Intended for v = 3000 mm / 9'10"FlushType of pointAMOrder No.8274615AMXLVolvo Tooth SystemOrder No.82743LA15FC35Point kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inHDump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge, Pos. G mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft inSTE H T* SEG**938713,12,53,33,4288015801580149028003516908310150027003760567014101890671134.13.34.34.59'5"5'2"5'2"4'11"9'2"0'1.4"372027'3"4'11"8'10"12'4"18'7"4'7"6'3"670'4.4"STE H T*938713,02,43,23,3288015801560149028003515303.93.14.14.39'5"5'2"5'1"4'10"9'2"0' 1.4"33808290 27'2"1480 4'10"2720 8'11"3790 12'5"5680 18'7"1420 4'8"1920 6'4"670'3.5"STE H T* SEG**938733,42,73,63,7288016501630156028003517608390156026503760574014601910671184.43.54.74.99'5"5'5"5'4"5'1"9'2"0'1.4"3890L120E27'6"5'1"8'8"12'4"18'10"4'9"6'3"670'4.7"* Dimensions based on 15AML points. Other points may affect dimensions differently.** SEG = Segments6789STE H T*938733,3 4.32,6 3.43,5 4.53,6 4.72880 9'5"1650 5'5"1610 5'3"1550 5'1"2800 9'2"35 0'1.4"1610 35508370155026703780574014701940679527'5"5'1"8'9"12'5"18'10"4'10"6'4"670'3.7"STE H T* SEG**805763,42,73,63,7300015601640146029203516208290147027203760576013901890671104.43.54.74.99'10"5'1"5'4"4'10"9'7"0'1.4"357027'2"4'10"8'11"12'4"18'11"4'7"6'2"670'4.3"STE H T*805763,32,63,53,630001560162014602920351590827014602730379057601400191067884.33.44.54.79'10"5'1"5'4"4'10"9'7"0'1.4"352027'1"4'10"9'0"12'5"18'11"4'7"6'3"670'3.5"51
Flat floor bucketsIntended for welded teeth options onlyThe buckets are intended for earth moving, overburdenclearing, landscaping, etc, and are ideal for use in softground conditions.MN2135(7')H J LAT EScyevdbdbL120EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSTE P T* FF821183,02,43,23,3288016701550145028003517303.93.14.14.39'5"5'6"5'1"4'9"9'2"0'1.4"3800STE P FF821183,02,43,23,3288014101540119028003516003.93.14.14.39'5"4'7"5'1"3'11"9'2"0'1.4"3520STE P T* FF826073,42,73,63,7288018101620161028003519004.43.54.74.99'5"5'11"5'4"5'3"9'2"0'1.4"4190STE P FF826073,42,73,63,7288015401610134028003517704.43.54.74.99'5"5'1"5'3"4'5"9'2"0'1.4"3900A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in8160136027403780560012201710629426'9"4'5"9'0"12'5"18'4"4'0"5'7"620'3.7"7880112029303790560010401640628225'10"3'8"9'7"12'5"18'4"3'5"5'5"620'3.2"8230142026903790570012801740628627'0"4'8"8'10"12'5"18'8"4'3"5'9"620'3.4"7950118028803800570011001680627326'1"3'11"9'6"12'6"18'8"3'7"5'6"620'2.9"* Dimensions based on 15AMXL points. Other points may affect dimensions differently.52
Flat floor bucketsType of adapterFlushWeld-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82743LA15FC35Type of pointAMPoint kit (set of 8)Volvo Tooth SystemOrder No.8274615AMXLType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft inSTE H T* FF823613,02,43,23,32880156015501450280035165082801470265037805670130017403.93.14.14.39'5"5'1"5'1"4'9"9'2"0'1.4"364027'2"4'10"8'8"12'5"18' 7"4'3"5'8"630'3.8"STE H FF823613,02,43,23,32880129015401190280035152080001220285037905670112016803.93.14.14.39'5"4'3"5'1"3'11"9'2"0'1.4"336026'3"4'0"9'4"12'5"18'7"3'8"5'6"630'3.4"L120E* Dimensions based on 15AMXL points. Other points may affect dimensions differently.63976385STE H T* FF825963,42,73,63,728801630162015302800351740834015302600379057601350177063874.43.54.74.99'5"5'4"5'4"5'0"9'2"0'1.4"384027'4"5'0"8'7"12'5"18'11"4'5"5'9"630'3.4"STE H FF825963,42,73,63,728801370161012702800351610806012802800380057601170171063754.43.54.74.99'5"4'6"5'3"4'2"9'2"0'1.4"356026'5"4'3"9'2"12'6"18'11"3'10"5'7"630'3"53
Rock bucketsIntended for welded teeth options onlyThe buckets are designed for loading material thatrequire high penetration and breakout forces.The buckets have low-cut sides to facilitate penetrationinto the material.MNLH J2135(7')AT EScyevdbL120EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSPN P BOE**938892,72,22,83,0288016801540144028403520103.52.93.73.99'5"5'6"5'1"4'8"9'4"0'1.4"4420SPN P T* SEG***938892,72,22,83,0288018701550163028403520903.52.93.73.99'5"6'2"5'1"5'4"9'4"0'1.4"4600SPN P T*938892,62,12,72,9288018701550163028403519503.42.73.63.79'5"6'2"5'1"5'4"9'4"0'1.4"4290SPN P938892,62,12,72,9288016001520136028403518103.42.73.63.79'5"5'3"5'0"4'6"9'4"0'1.4"3990A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in548200138027903790562013101850678426'11"4'6"9'2"12'5"18'5"4'4"6'1"670'3.3"840015502650378056201450191027'7"5'1"8'8"12'5"18'5"4'9"6'3"670'3.6"8400155026603780562014501910* Dimensions based on L5 tires and 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment6793679227'7"5'1"8'9"12'5"18'5"4'9"6'3"670'3.6"8100130028603820562012701850675826'7"4'3"9'4"12'6"18'5"4'2"6'1"670'2.3"
Rock bucketsBolt-on edge kit Order No. 93419Type of adapter1 1/2 LegWeld-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82744LA15TL35Segment kit (set of 7)VolvoOrder No.93899FlushType of pointAMOrder No.8274615AMXLVolvo Tooth SystemOrder No.82743LA15FC35Point kit (set of 8)Volvo Tooth SystemOrder No.8274215AMLL120EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSPN P BOE**938903,02,43,23,3288017501580150028403519103.93.14.14.39'5"5'9"5'2"4'11"9'4"0'1.4"4220SPN P T* SEG***938903,02,43,23,3288019401590170028403519903.93.14.14.39'5"6'4"5'3"5'7"9'4"0'1.4"4400SPN P T*938902,92,33,03,2288019401590170028403518503.83.04.04.29'5"6'4"5'3"5'7"9'4"0'1.4"4080SPN P938902,92,33,03,2288016701560143028403517203.83.04.04.29'5"5'6"5'1"4'8"9'4"0'1.4"3790A Overall length mm ft inE Digging depth, max dump (S) mm ft inHDump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in8180137028003810570013201870676426'10"4'6"9'2"12'6"18'8"4'4"6'2"670'2.5"838015402670380056901460193027'6"5'1"8'9"12'6"18'8"4'10"6'4"670'2.9"* Dimensions based on L5 tires and 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment67738380154026703800570014601930677227'6"5'1"8'9"12'6"18'8"4'10"6'4"670'2.8"8080129028703840570012801870673826'6"4'3"9'5"12'7"18'8"4'2"6'2"670'1.5"55
Rock bucketsIntended for welded teeth options onlyThe buckets are designed for loading material thatrequire high penetration and breakout forces.The buckets have low-cut sides to facilitate penetrationinto the material.MNLH J2135(7')AT EScyevdbL120EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inb Bucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbSPN H BOE**938883,02,43,23,3288016001580150028403518203.93.14.14.39'5"5'3"5'2"4'11"9'4"0'1.4"4000SPN H T* SEG***938883,02,43,23,3288017901590170028403519003.93.14.14.39'5"5'11"5'3"5'7"9'4"0'1.4"4180SPN H T*938882,92,33,03,2288017901590170028403517503.83.04.04.29'5"5'11"5'3"5'7"9'4"0'1.4"3870SPN H938882,92,33,03,2288015301560143028403516203.83.04.04.29'5"5'0"5'1"4'8"9'4"0'1.4"3570A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in568290147027303810576014001910676627'2"4'10"9'0"12'6"18'11"4'7"6'3"670'2.6"849016402600380057601540196027'10"5'5"8'6"12'6"18'11"5'1"6'5"* Dimensions based on L5 tires and 15AML points. Other points may affect dimensions differently.** BOE = Bolt-on edge*** SEG = Segment6775670'3"8490164026003800576015401960677427'10"5'5"8'6"12'6"18'11"5'1"6'5"670'2.9"8190139028003830576013601910674026'10"4'7"9'2"12'7"18'11"4'6"6'3"670'1.6"
Rock bucketsBolt-on edge kit Order No. 93419Type of adapter1 1/2 LegWeld-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82744LA15TL35Segment kit (set of 7)VolvoOrder No.93899FlushType of pointAMOrder No.8274615AMXLVolvo Tooth SystemOrder No.82743LA15FC35Point kit (set of 8)Volvo Tooth SystemOrder No.8274215AML57
Rock bucketsIntended for welded teeth options onlyThe buckets are designed for loading material thatrequire high penetration and breakout forces.The buckets have low-cut sides to facilitate penetrationinto the material.MNLH J2135(7')AT EScyevdbType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inbBucket length mm fta inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* Dimensions based on L5 tires and 15AML points.Other points may affect dimensions differently.** SEG = Segment58STE RO P T* SEG**938873,12,53,33,428801730159014802800352060817013602810380056901300186067734.13.34.34.59'5"5'8"5'3"4'10"9'2"0'1.4"454026'10"4'5"9'3"12'6"18'8"4'3"6'1"670'2.9"L120ESTE RO P T*938873,02,43,23,328801730159014802800351910817013602810380057001300186067723.93.14.14.39'5"5'8"5'3"4'10"9'2"0'1.4"421026'10"4'5"9'3"12'6"18'8"4'3"6'1"670'2.8"
Rock bucketsSegment kit (set of 7)VolvoOrder No.93424Type of adapter1 1/2 LegWeld-on adapter kit (set of 8)Volvo Tooth SystemOrder No.82744LA15TL35FlushVolvo Tooth SystemOrder No.82743LA15FC35Type of pointAMOrder No.8274615AMXLPoint kit (set of 8)Volvo Tooth SystemOrder No.8274215AML59
Refuse bucketsIntended for bolted options onlyThe buckets are designed for handling refuse materialand can be equipped with a steel or rubber cutting edge.MN2135(7')H J LAT EScyevdbdbL110EType of applicationOrder No.REF P BOE* (R)82511REF P BOE* (S)82511REF P82511REF H BOE* (R)82512REF H BOE* (S)82512REF H82512VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inbBucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lb5,54,75,86,1300019902060173029603522307.26.17.67.99'10"6'6"6'9"5'8"9'8"0'1.4"49205,54,75,86,1300020101940176029603521007.26.17.67.99'10"6'7"6'4"5'9"9'8"0'1.4"46405,34,55,65,8300019401920168029603518306.95.97.37.69'10"6'4"6'3"5'6"9' 8"0'1.4"40405,54,75,86,1300018402060173029603521507.26.17.67.99'10"6'0"6'9"5'8"9'8"0'1.4"47305,54,75,86,1300018601940176029603520207.26.17.67.99'10"6'1"6'4"5'9"9'8"0'1.4"44505,34,55,65,8300017901920168029603517506.95.97.37.69'10"5'10"6'3"5'6"9'8"0'1.4"3850A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* BOE = Bolt-on edge(R) = Rubber Bolt-on kit(S) = Steel Bolt-on kit6084501650241035906040135016106321127'9"5'5"7'11"11'9"19'10"4'5"5'4"630'8.3"8370161024803710604014501770638827'6"5'4"8'2"12'2"19'10"4'9"5'10"630'3.58270153025503740604014101790636127'2"5'0"8'4"12'3"19'10"4'7"5'10"630'2.4"85601750233035906100142016306321328'1"5'9"7'8"11'9"20'0"4'8"5'4"630'8.4"8480172024003710610015301790639127'10"5'8"7'11"12'2"20'0"5'0"5'10"630'3.6"8380164024803740611014901810636327'6"5'4"8'2"12'3"20'0"4'11"5'11"630'2.5"
Refuse bucketsREF Steel kit Order No. 82568 REF Rubber kit Order No. 82574L120EType of applicationOrder No.REF P BOE* (R)82511REF P BOE* (S)82511REF P82511REF H BOE* (R)82512REF H BOE* (S)82512REF H82512VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inbBucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in* BOE = Bolt-on edge(R) = Rubber Bolt-on kit(S) = Steel Bolt-on kit5,54,75,86,1300019902060173029603522308550167024703660611013801710642187.26.17.67.99'10"6'6"6'9"5'8"9'8"0'1.4"492028'1"5'6"8'1"12'0"20'0"4'6"5'7"640'8.6"5,54,75,86,130002010194017602960352100847016402540378061101480186064967.26.17.67.99'10"6'7"6'4"5'9"9'8"0'1.4"464027'10"5'4"8'4"12'5"20'1"4'10"6'1"640'3.8"5,34,55,65,830001940192016802960351830837015602620381061101450188064686.95.97.37.69'10"6'4"6'3"5'6"9'8"0'1.4"404027'6"5'1"8'7"12'6"20'1"4'9"6'2"640'2.7"5,54,75,86,1300018402060173029603521508660177024003650617014601720652207.26.17.67.99'10"6'0"6'9"5'8"9'8"0'1.4"473028'5"5'10"7'10"12'0"20'3"4'9"5'8"650'8.7"5,54,75,86,130001860194017602960352020858017402470378061701560188065987.26.17.67.99'10"6'1"6'4"5'9"9'8"0'1.4"445028'2"5'9"8' 1"12'5"20'3"5'1"6'2"650'3.9"5,34,55,65,830001790192016802960351750848016602540380061701520190065716.95.97.37.69'10"5'10"6'3"5'6"9'8"0'1.4"385027'10"5'5"8'4"12'6"20'3"5'0"6'3"650'2.8"61
Light material bucketsThe buckets are designed for handling materials of lowdensity, such as snow, coal, wood chips etc.Note: The buckets can be used for both for L110E andL120E, depending on the density of the material.MNLH J2135(7')AT EScyevdbEquipped as standard with bolt-on edgeL110EL120EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inbBucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbLM P BOE926905,54,55,86,1300020101720176029603521107.25.97.67.99'10"6'7"5'8"5'9"9'9"0'1.4"4660LM H BOE926895,54,55,86,1300018601720176029603520307.25.97.67.99'10"6'1"5'8"5'9"9'9"0'1.4"4480LM P BOE926905,54,55,86,1300020101720176029603521107.25.97.67.99'10"6'7"5'8"5'9"9'9"0'1.4"4660LM H BOE926895,54,55,86,1300018601720176029603520307.25.97.67.99'10"6'1"5'8"5'9"9'9"0'1.4"4480A Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft in8370161024903710577014601800648727'5"5'3"8'2"12'2"18'11"4'10"5'11"640'3.4"8480171024103710583015201790639127'10"5'8"7'11"12'2"19'1"5'0"5'10"630'3.6"8470164025603780583015001890659527'9"5'4"8'5"12'5"19'2"4'11"6'2"650'3.7"8580174024703780590015601880659828'2"5'8"8'1"12'5"19'4"5'1"6'2"650'3.9"62
Light material bucketsThe buckets are designed for handling materials of lowdensity, such as wood chips etc.Note: The buckets can be used for both for L110E andL120E, depending on the density of the material.MNLH J2135(7')AT ESdbEquipped as standard with bolt-on edgeType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3Volume at 105% fill factor m 3 yd 3Volume at 110% fill factor m 3 yd 3v Bucket width mm ft inbBucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbA Overall length mm ft inE Digging depth, max dump (S) mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inN Reach at 45° discharge mm ft inS Max forward dump at lowestlifting arm pos. °T Digging depth mm ft inL110ELM H BOE926849,57,310,010,53400215020002040336025225087801970220037006000173018006310212.49.513.013.711'2"7'1"6'7"6'8"11'0"0'1"497028'10"6'6"7'3"12'2"19'8"5'8"5'11"630' 4"L120ELM H BOE926849,57,310,010,53400215020002040336025225088802000226037706060176019106510912.49.513.013.711'2"7'1"6'7"6'8"11'0"0'1"497029'1"6'7"7'5"12'4"19'11"5'9"6'3"650'4.3"63
Hi-Tip light material bucketsThe buckets are designed for handling low densitymaterials e.g. coal, coke, wood chips, etc. Because it isdumped over a special frame, the unloading height isconsiderably increased.Note: Requires 3 rd hydraulic function.PMLH JAcyevdbEquipped as standard with bolt-on edgeL110EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3v Bucket width mm ft inbBucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbHIT P BOE820425,03,7300020301690173029702521806.54.89'10''6'8''5'7''5'8''9'9''0'1''4810HIT H BOE820435,03,7300018401690173029702520606.54.89'10''6'0''5'7''5'8''9'9''0'1''4540HIT P BOE820407,06,3300022201880192029702524809.28.29'10''7'3''6'2''6'4''9'9''0'1''5470HIT LM H BOE820417,06,3300020301880192029702523209.28.29'10''6'8''6'2''6'4''9'9''0'1''5120A Overall length mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inP Max dump at max liftingarm height °839045304900677015204527'6''14'10''16'1''22'3''4'12''45843045804950682015604527'8''15'0''16'3''22'5''5'1''45858044004900683016604528'2''14'5''16'1''22'5''5'5''45862044504950688016904528'3''14'7''16'3''22'7''5'7''4564
Hi-Tip light material bucketsThe buckets are designed for handling low densitymaterials e.g. coal, coke, wood chips, etc. Because it isdumped over a special frame, the unloading height isconsiderably increased.Note: Requires 3 rd hydraulic function.PMLH JAcyevdbEquipped as standard with bolt-on edgeL120EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3v Bucket width mm ft inbBucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbHIT P LM BOE820425,03,7300020301690173029702521806.54.89'10''6'8''5'7''5'8''9'9''0'1''4810HIT H LM BOE820435,03,7200018401690173029702520606.54.89'10''6'0''5'7''5'8''9'9''0'1''4540HIT P LM BOE820407,06,3300022201880192029702524809.28.29'10''7'3''6'2''6'4''9'9''0'1''5470HIT H LM BOE820417,06,3300020301880192029702523209.28.29'10''6'8''6'2''6'4''9'9''0'1''5120A Overall length mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inP Max dump at max liftingarm height °849045804940682015504527'10''15'0''16'2''22'5''5'1''45854046304990686015904528'0''15'2''16'4''22'6''5'3''45868044504940687016904528'6''14'7''16'2''22'6''5'7''45872045004990692017304528'7''14'9''16'4''22'8''5'8''4565
Hi-Tip light material bucketsThe buckets are designed for handling low densitymaterials e.g. coal, coke, wood chips, etc. Because it isdumped over a special frame, the unloading height isconsiderably increased.Note: Requires 3 rd hydraulic function.PMLHJAcyevdbEquipped as standard with bolt-on edge L110E L120EType of applicationOrder No.VolumeHeaped ISO/SAE m 3 yd 3Struck ISO/SAE m 3 yd 3v Bucket width mm ft inbBucket length mm ft inc Bucket height mm ft ind Bucket depth mm ft ine Bucket width over sidecutters mm ft iny Cutting edge thickness mm ft inBucket weight kg lbHIT P LM BOE820449,58,63400238020402090336025268012.411.311'2''7'10''6'8''6'10''11'0''0'1''5910HIT H LM BOE820459,58,63400220020402090336025256012.411.311'2''7'3''6'8''6'10''11'0''0'1''5650HIT P LM BOE820449,58,63400238020402090336025268012.411.311'2''7'10''6'8''6'10''11'0''0'1''5910HIT H LM BOE820459,58,63400220020402090336025256012.411.311'2''7'3''6'8''6'10''11'0''0'1''5650A Overall length mm ft inH Dump clearance mm ft inJ Lift height under level bucket mm ft inL Overall operating height mm ft inM Dump reach mm ft inP Max dump at max liftingarm height °875042804890697017804528'8''14'1''16'1''22'10''5'10''45879043304940702018204528'10''14'2''16'2''23'0''5'12''45885043304930702018104529'0''14'2''16'2''23'0''5'11''45889043804980707018504529'2''14'4''16'4''23'2''6'1''4566
Log grapplesLog handlingCenturies of timber handling in Sweden have given usthe experience and knowlege to design superior loggrapples. This experience, together with our own developmentwork, has produced a wide range of grapples.Versatility is a must, since the demands of the work varywidely. They may include handling different lengths,transporting logs over uneven ground, gripping and holdingone log, whole stems, etc. These are the points wetake into consideration when designing our complete loggrapple range, which permits all types of timber to behandled under the most diverse conditions.Torque Parallel Linkage has advantages that no othersystem can boast. Generous reach and lifting heightpermit the work to be done quickly and safely.If the grapple has to come in from above for final stackingof timber or when unloading a truck, the machinemust have sufficient breakout and back-tilting torque. Ifthe machine is not strong enough to break out the loadfrom the top, the tines have to be forced between thelogs, increasing the risk of damage to the logs and thevehicle.Rated operating loads for log grapples are calculatedfor a wheel loader fitted with approved counterweightsfor timber handling.The rated operating load capacity specified will be influencedif optional equipment is fitted to the attachmentor the loader.Log grapple specifications on the following pagesare calculated for machines equipped with loggingcounterweight and tires:L110E750/65R25L120E750/65R2567
Log grapplesSelecting a log grappleOne of the fundamental principles in choosing a loggrapple for handling round wood is that the longer thetimber is, the smaller the grip area and the wider thegrapple must be. The log grapples are designed differentlydepending on how the machine works. Size isnormally expressed in m 2 /ft 2 . The length of the timberthen determines how much can be carried.Log grapples always require a 3 rd hydraulicfunction.A B C DAThe unloading grapple has short, rounded tines, making iteasier to fill the grapple when unloading a vehicle. Long,straight tines could damage both the timber and the vehicle ifused for his purpose.BThe sorting grapple has relatively long and straight tines thatcan slide along the ground so the grapple can be easily filledwhen loading from stacks and sorting bunkers.CThe general purpose grapple is an allround grapple forhandling and sorting tree length stems or for gripping singlestems. It has longer tines than the sorting grapple.DThe tropical timber grapple is a wide grapple with twoseparate clamping arms to hold large, heavy stems securely.Principally intended for handling large diameter and highdensitytimber of the tropical type.Heel/kickoutHydraulic heel/kickout is available for unloading andsorting grapples. The heel is used, for example, for holdinga single log in a large grapple. The kickout is usedto make higher stacks, since the grapples do not have tobe tilted to empty; instead, the log is pushed out, makingit possible to reach about half a meter higher.Supplied as an assembly kit. Assembly not included inthe price.Note: Requires 4 th hydraulic function.68Type of applicationFor grappleOrder No.Weight kg lbMD min mm ft inFor grappleOrder No.Weight kg lbMD min mm ft in80834/808358083626017080831/8033280833330220L110E/L120EHK OUT5700'7''7300'9''MD
Log grapplesUnloading grappleGrapples for unloading timber from e.g. vehicles andplacing it in stacks. The grapples have short tines anda clamping arm that gives the grapples a large opening.The short tines permit effective and gentle unloading.Replaceable wear plates are standard.Note: Requires 3 rd hydraulic function.Can be equipped with hydraulic heel/kickout.A20°N 45°MAX20°KJPMDMAX FD B HIRQECLGutsL110EL120EType of applicationOrder NoLog length m ftA Grapple area m 2 ft 2Rated operating load kg lbs Grapple width mm ft int Grapple length mm ft inu Grapple height mm ft inGrapple weight kg lbUNL GR H808344,81,86300163021001940140015.6'19.4138905'4"6'10"6'4"3080UNL GR H808314,82,45850163023502190155015.6'25.8129005'4"7'9"7'2"3410UNL GR H808344,81,86800163021001940140015.6'19.4149905'4"6'10"6'4"3080UNL GR H808314,82,46400163023502190155015.6'25.8141105'4"7'9"7'2"3410B Dumping clearance atmax. HPH, dump 20° mm ft inC Dumping reach at max.HPH, dump 20° mm ft inD Dumping clearance atmax. HPH, dump 45° mm ft inE Dumping reach atmax. HPH, dump 45° mm ft inF Dumping clearance atparallel lifting arm pos. mm ft inG Dumping reach atparallel lifting arm pos. mm ft inH Max. dumpingclearance mm ft inI Overall operatingheight mm ft inJ Height upper clampat K mm ft inK Max. opening width mm ft inL Reach at groundposition mm ft inMD Min. handle diameter mm ft inN Max. dumping angleat max. HPH °O Grading angle °P Dumping clearance atmax. HPH, max. dump mm ft inQ Dumping reach at max.HPH, max. dump mm ft inR Tine tip length mm ft in3740144032601200179023104580637024302780157012007382290071073012'3"4'9"10'8"3'11"5'11"7'7"15'0"20'11"7'11"9'1"5'2"3'11"73829'6"2'4"2'5"3730155032001290178024204630670028003160168013807482280077084012'3"5'1"10'6"4'3"5'10"7'11"15'2"22'0"9'2"10'4"5'6"4'6"74829'2"2'6"2'9"3800148033201240179023904640642024302780167012007384297075073012'6"4'10"10'11"4'1"5'11"7'10"15'3"21'1"7'11"9'1"5'6"3'11"73849'9"2'6"2'5"3800159032701330179025004690675028003160178013807384287081084012'5"5'2"10'9"4'4"5'10"8'2"15'5"22'2"9'2"10'4"5'10"4'6"73849'5"2'8"2'9"HPH = Hinge pin height69
Log grapplesSorting grappleGrapples for feeding sorting plants from a stack. Theyhave relatively long tines to reach into bunkers. Theclamping arm is designed to provide a large opening.Replaceable wear plates are standard.Note: Requires 3 rd hydraulic function.Can be equipped with hydraulic heel/kickout.A20°N 45°MAX20°KJPMDMAX FD B HIuRQECLGtsL110EL120EType of applicationOrder NoLog length m ftA Grapple area m 2 ft 2Rated operating load kg lbs Grapple width mm ft int Grapple length mm ft inu Grapple height mm ft inGrapple weight kg lbSORT GR H808354,8 15.6'1,8 19.46300 138901630 5'4"2090 6'10"1940 6'4"1400 3080SORT GR H808324,8 15.6'2,4 25,85850 129001630 5'4"2320 7'7"2200 7'2"1590 3500SORT GR H808324,8 15.6'2,4 25.86400 141101630 5'4"2320 7'7"2200 7'2"1590 3500SORT GR H808354,8 15.6'1,8 19.46800 149901630 5'4"2090 6'10"1940 6'4"1400 3080B Dumping clearance atmax. HPH, dump 20° mm ft inC Dumping reach at max.HPH, dump 20° mm ft inD Dumping clearance atmax. HPH, dump 45° mm ft inE Dumping reach atmax. HPH, dump 45° mm ft inF Dumping clearance atparallel lifting arm pos. mm ft inG Dumping reach atparallel lifting arm pos. mm ft inH Max. dumpingclearance mm ft inI Overall operatingheight mm ft inJ Height upper clampat K mm ft inK Max. opening width mm ft inL Reach at groundposition mm ft inMD Min. handle diameter mm ft inN Max. dumping angleat max. HPH °O Grading angle °P Dumping clearance atmax. HPH, max. dump mm ft inQ Dumping reach at max.HPH, max. dump mm ft inR Tine tip length mm ft in35201670296013101570255045806360243026301860106065752660880102011'7"5'6"9'8"4'4"5'2"8'4"15'0"20'10"8'0"8'8"6'1"3'6"65758'9"2'11"3'4"34901830287014401540270046106650279029902020120066762520960118011'6"6'0"9'5"4'9"5'1"8'10"15'1"21'10"9'2"9'10"6'8"3'11"66768'3"3'2"3'10"356018702940148015502770467067002790299021201200657825901010118011'8"6'1"9'8"4'10"5'1"9'1"15'4"22'0"9'2"9'10"7'0"3'11"65788'6"3'4"3'10"35901710303013501570262046406420243026301970106065772730920102011'9"5'7"9'11"4'5"5'2"8'7"15'3"21'1"8'0"8'8"6'5"3'6"65778'11"3'0"3'4"HPH = Hinge pin height70
Log grapplesGeneral purpose grappleGrapples for handling and sorting different types oftimber, including tree-length stems.A small minimum grip area can be obtained for handlingsingle stems.Replaceable wear plates are standard.Note: Requires 3 rd hydraulic function.usA45°NMAX20°O20°MDQECLGRHKBP J DFItL110EL120EType of applicationOrder NoA Grapple area m 2 ft 2Rated operating load kg lbs Grapple width mm ft int Grapple length mm ft inu Grapple height mm ft inGrapple weight kg lbGP GR H823391,36500163017502000135014.0143305'4"5'9"6'7"2980GP GR H823401,36400120018102000129014.0141103'11"5'11"6'7"2840GP GR H823391,37140163017502000135014.0157405'4"5'9"6'7"2980GP GR H823401,36970120018102000129014.0153703'11"5'11"6'7"2840B Dumping clearance atmax. HPH, dump 20° mm ft inC Dumping reach at max.HPH, dump 20° mm ft inD Dumping clearance atmax. HPH, dump 45° mm ft inE Dumping reach atmax. HPH, dump 45° mm ft inF Dumping clearance atparallel lifting arm pos. mm ft inG Dumping reach atparallel lifting arm pos. mm ft inH Max. dumpingclearance mm ft inI Overall operatingheight mm ft inJ Height upper clampat K mm ft inK Max. opening width mm ft inL Reach at groundposition mm ft inMD Min. handle diameter mm ft inN Max. dumping angleat max. HPH °O Grading angle °P Dumping clearance atmax. HPH, max. dump mm ft inQ Dumping reach at max.HPH, max. dump mm ft inR Tine tip length mm ft inHPH = Hinge pin height34701960279015501520284046405790232023802160310657724101040127011'5"6'5"9'2"5'1"5'0"9'4"15'3"19'0"7'7"7'10"7'1"1'0"65777'11"3'5"4'2"34502070272016401500294046806240232023702270320657823201100127011'4"6'10"8'11"5'5"4'11"9'8"15'4"20'6"7'7"7'9"7'5"1'0"65787'7"3'7"4'2"35402000285015901520291047005840232023802260310657924801090127011'7"6'7"9'4"5'3"5'0"9'7"15'5"19'2"7'7"7'10"7'5"1'0"65798'2"3'7"4'2"35102110279016801500302047506300232023702370320658023901140127011'6"6'11"9'2"5'6"4'11"9'11"15'7"20'8"7'7"7'9"7'9"1'0"65807'10"3'9"4'2"71
Log grapplesSwivel wood clampThe swivel wood clamp (SWC) handles pulpwood in2–3 m/ 6'6''–9'8'' lengths and is mounted on the attachmentbracket.It is designed for unloading vehicles to a stack or feedingtable.It is a also suitable for transporting wood from a stack toa feeding table.The grapple can be positioned at either position ”a” orposition ”b” depending on the size of the grapple, densityand length of timber. The specifications apply for a machinefitted with logging counterweight.Tipping load applies with horizontal arms and the framein a vertical position.Single-acting lift function is recommended.Note: Requires 3 rd and 4 th hydraulic functions.sua350bb a25°BFA2A1AtyCC1xEDvL110EL120EType of applicationOrder NoGrapple area m 2ft 2Grapple weight kg lbFrame Order No*)s Frame height mm ft int Frame length mm ft inu Frame width mm ft inv Grapple fully closed,max. outside dimension mm ft inx Grapple fully closed,min. height mm ft iny Grapple width mm ft inFrame weight kg lbSWC H821310,5-1,55.4-16.1880821302700224013201450143084095019408'10''7'4''4'4''4'9''4'8''2'9''2090SWC H821320,7-1,87.5-19.4900821302700224013201690152084095019808'10''7'4''4'4''5'7''4'12''2'9''2090SWC H821330,7-2,07.5-21.5930821302700224013201780161084095020508'10''7'4''4'4''5'10''5'3''2'9''2090SWC H821310,5-1,55.4-16.1880 1940821302700 8'10''2240 7'4''1320 4'4''145014308409504'9''4'8''2'9''2090SWC H821320,7-1,87.5-19.4900 1980821302700 8'10''2240 7'4''1320 4'4''169015208409505'10''4'12''2'9''2090SWC H821330,7-2,07.5-21.5930 2050821302700 8'10''2240 7'4''1320 4'4''178016108409505'10''5'3''2'9''2090Rated operating loadPosition a kg lbPosition b kg lbA Center of grapplemax. reach mm ft inA 1Center of grapple topposition mm ft inA 2Center of grapple topposition, tilted backwards25 ° mm ft inB Frame length to centerof grapple mm ft inC Max. height underclosed grapple mm ft inC 1Max. height under closedgrapple, top position tiltedbackwards 25 ° mm ft inD Overall operating height mm ft inE Max. height under opengrapple mm ft inF Width outside grapplefully opened mm ft in325034503380248013301710386046106500436036307160761011'1''8'2''4'4''5'7''12'8''15'1''21'4''14'4''11'11''325034503380248013301710371044606500427038607160761011'1''8'2''4'4''5'7''12'2''14'8''21'4''14'0''12'8''325034503380248013301710364043906500424040007160761011'1''8'2''4'4''5'7''11'11''14'5''21'4''13'11''13'1''365039003450251013501710394046906600444036308050860011'4''8'3''4'5''5'7''12'11''15'5''21'8''14'7''11'11''365039003450251013501710379045406600435038608050860011'4''8'3''4'5''5'7''12'5''14'11''21'8''14'3''12'8''365039003450251013501710372044706600432040008050860011'4''8'3''4'5''5'7''12'2''14'8''21'8''14'2''13'1''*) Includes rotator72
Log grapplesTropical timber grappleThe tropical timber grapple is wide and has two separateclamping arms for holding large, heavy stems.For handling large-diameter and high-density timber.Note: Requires 3 rd hydraulic function.sANMAX20°20°45°OKFJP D B HIuQECLGtL110EL120EType of applicationOrder No.A Grapple area m 2 ft 2Rated operating load kg lbs Grapple width mm ft int Grapple length mm ft inu Grapple height mm ft inGrapple weight kg lbTROP GR H826951,1 11,86950 153202500 8'2"1600 5'3"1460 4'9"1500 3300TROP GR H826951,1 11,87520 165802500 8'2"1600 5'3"1460 4'9"1500 3300B Dumping clearance atmax. HPH, dump 20° mm ft inC Dumping reach at max.HPH, dump 20° mm ft inD Dumping clearance atmax. HPH, dump 45° mm ft inE Dumping reach atmax. HPH, dump 45° mm ft inF Dumping clearance atparallel lifting arm pos. mm ft inG Dumping reach atparallel lifting arm pos. mm ft inH Max. dumping clearance mm ft inI Overall operating height mm ft inJ Height upper clamp at K mm ft inK Max. opening width mm ft inL Reach at ground position mm ft inN Max. dumping angleat max. HPH °O Grading angle °P Dumping clearance atmax. HPH, max. dump mm ft inQ Dumping reach at max.HPH, max. dump mm ft in335018202740138014002700445053002020198020806374246094011'0"6'0"9'0"4'6"4'7"8'10"14'7"17'5"6'7"6'6"6'10"63748'1"3'1"342018702810143014002780451053402020198022006376252099011'3"6'2"9'2"4'8"4'7"9'1"14'9"17'6"6'7"6'6"7'2"63768'3"3'3"HPH = Hinge pin height73
Fork attachmentsFork attachments for varying needsDue to their special features, flexibility, manoeuverabilityand unique lift-arm system, Volvo wheel loaders are usedin many different types of applications. The attachmentbracket permits the machine to be utilized effectivelywhere previously only special purpose machines such asfork-lift trucks and mobile cranes could operate. Thestability of Volvo wheel loaders and the reach and parallellift-arm action of the loader unit make them particularlysuitable for work with fork attachments.In material handling yards, warehouses and harbors,maximum use is made of the available space. Here theVolvo wheel loader's lift-arm system and efficient attachmentsare a necessity. Their high lift height and longreach permit work with high stacks. They can also loadwide vehicles from one side, permitting short work cycles.Fork qualityFork frames and pallet forks must be able to withstandthe full lifting capacity of the machine. The fork tines aredesigned according to ISO 2330, and they are made ofhigh grade, hardened and tempered steel, which meetthese demands with excess margin.It is the manufacturer's responsibility to furnish data andinformation on attachments together with the loaders. Wecarry out inspections and classifications according tocurrent standards.Fork tine wear (Acc. to ISO 5057)The fork tine shall be thoroughly checked for wear,special attention being paid to the vicinity of the heel.If the thickness of the tine is reduced to 90% of theoriginal thickness, or to the minimum thickness specifiedby the fork tine or equipment manufacturer, the fork tineshall be withdrawn from service.All Volvo pallet fork tines are marked with:1 Max. load per tine in kg2 Spacing for max. load in mm3 Material thickness in mm74
Approval and legal provisionsThe rated operating load capacity is determinedaccording to the European Standard EN 474–3.For countries outside the European Common Market,other safety requirements might apply, so the user shouldalways check local regulations.The determined operating load for Volvo wheel loaders,with respect to attachment load center distance, isspecified in the table below.L110E Stone fork**Ground mm ft incondition 600 2'0"Rough terrain kg lb23.5R25 6100 13448Firm and level ground kg lb23.5R25 8100 17857Static tipping kg lbload full turn23.5R25 10050 22156*) Limited by the attachment**) Loader equipped with logging counterweight and L5 tiresFork attachmentsNOTE: Always operate with load in lowered position.Transport speed shall be adapted to ground conditions.Load shall be lifted with minimum incline.Stacking should be performed with fork frame or forkshank vertical.The rated operation load capacity given in the tablewill be influenced if optional equipment is fitted to theattachment.Rated operating load capacity at load center distance of:L110E Pallet fork tines, straight. Standard, capacity 4300 kg / 9480 lb, 600 mm/2'0" per armGround mm ft in mm ft in mm ft in mm ft in mm ft in mm ft incondition 500 1'8" 600 2'0" 700 2'4" 800 2'8" 900 2'11" 1200 3'11"Rough terrain kg lb kg lb kg lb kg lb kg lb kg* lb*23.5R25 5350 11795 5150 11354 5000 11023 4850 10692 4700 10362 4300 9480750/65R25 5500 12125 5650 12456 5200 11464 5050 11133 4900 10803 4300 9480Firm and level ground kg lb kg lb kg lb kg lb kg* lb* kg* lb*23.5R25 7050 15543 6800 14991 6600 14550 6400 14110 5700 12566 4300 9480750/65R25 7300 16094 7100 15653 6850 15102 6450* 14220* 5700 12566 4300 9480Static tipping kg lb kg lb kg lb kg lb kg lb kg lbload full turn 23.5R25 8700 19180 8450 18629 8200 18078 7950 17527 7700 16976 7100 15653750/65R25 9100 20062 8800 19401 8500 18739 8250 18188 8000 17637 7350 16204L110E Pallet fork tines, straight. Break out, capacity 5900 kg / 13007 lb, 600 mm/2'0" per armGround mm ft in mm ft in mm ft in mm ft in mm ft in mm ft incondition 500 1'8'' 600 2'0'' 700 2'4'' 800 2'8'' 900 2'11'' 1200 3'11''Rough terrain kg lb kg lb kg lb kg lb kg lb kg lb23.5R25 5350 11795 5150 11354 5000 11023 4850 10692 4700 10362 4300 9480750/65R25 5500 12125 5350 11795 5200 11464 5050 11133 4900 10803 4500 9921Firm and level ground kg lb kg lb kg lb kg lb kg lb kg lb23.5R25 7050 15543 6800 14991 6600 14550 6400 14110 6200 13669 5700 12566750/65R25 7300 16094 7100 15653 6850 15102 6650 14661 6450 14220 5900* 13007*Static tipping kg lb kg lb kg lb kg lb kg lb kg lbload full turn 23.5R25 8700 19180 8450 18629 8200 18078 7950 17527 7700 16976 7100 15653750/65R25 9100 20062 8800 19401 8500 18739 8250 18188 8000 17637 7350 16204L110E Pallet fork tines, visibility optimized right/left, capacity 3900 kg / 8598 lb, 600 mm/2'0" per armGround mm ft in mm ft in mm ft in mm ft in mm ft in mm ft incondition 500 1'8'' 600 2'0'' 700 2'4'' 800 2'8'' 900 2'11'' 1200 3'11''Rough terrain kg lb kg lb kg lb kg lb kg lb kg* lb*23.5R25 5350 11795 5150 11354 5000 11023 4850 10692 4700 10362 3900 8598750/65R25 5500 12125 5350 11795 5200 11464 5050 11133 4900 10803 3900 8598Firm and level ground kg lb kg lb kg lb kg* lb* kg* lb* kg* lb*23.5R25 7050 15543 6800 14991 6600 14550 5850 12897 5200 11464 3900 8598750/65R25 7300 16094 7100 15653 6650* 14661* 5850 12897 5200 11464 3900 8598Static tipping kg lb kg lb kg lb kg lb kg lb kg lbload full turn 23.5R25 8700 19180 8450 18629 8200 18078 7950 17527 7700 16976 7100 15653750/65R25 9100 20062 8800 19401 8500 18739 8250 18188 8000 17637 7350 16204L110E Lumber fork tines, straight, capacity 4875 kg / 10747 lb, 600 mm/2'0" per armGround mm ft in mm ft in mm ft in mm ft in mm ft in mm ft incondition 500 1'8'' 600 2'0'' 700 2'4'' 800 2'8'' 900 2'11'' 1200 3'11''Rough terrain kg lb kg lb kg lb kg lb kg lb kg lb23.5R25 5350 11795 5150 11354 5000 11023 4850 10692 4700 10362 4300 9480750/65R25 5500 12125 5350 11795 5200 11464 5050 11133 4900 10803 4500 9921Firm and level ground kg lb kg lb kg lb kg lb kg lb kg* lb*23.5R25 7050 15543 6800 14991 6600 14550 6400 14110 6200 13669 4850 10692750/65R25 7300 16094 7100 15653 6850 15102 6650 14661 6450 14220 4850 10692Static tipping kg lb kg lb kg lb kg lb kg lb kg lbload full turn 23.5R25 8700 19180 8450 18629 8200 18078 7950 17527 7700 16976 7100 15653750/65R25 9100 20062 8800 19401 8500 18739 8250 18188 8000 17637 7350 1620475
Fork attachmentsRated operating load capacity at load center distance of:L120E Pallet fork tines, straight. Standard, capacity 4300 kg / 9480 lb, 600 mm/2'0" per armGround mm ft in mm ft in mm ft in mm ft in mm ft in mm ft incondition 500 1' 8'' 600 2' 0'' 700 2' 4'' 800 2' 8'' 900 2' 11'' 1200 3' 11''Rough terrain kg lb kg lb kg lb kg lb kg lb kg* lb*23.5R25 5800 12787 5650 12456 5450 12015 5300 11684 5150 11354 4300 9480750/65R25 6000 13228 5800 12787 5650 12456 5450 12015 5300 11684 4300 9480Firm and level ground kg lb kg lb kg lb kg* lb* kg* lb* kg* lb*23.5R25 7700 16976 7450 16424 7200 15873 6450 14220 5700 12566 4300 9480750/65R25 7950 17527 7700 16976 7350* 16204* 6450 14220 5700 12566 4300 9480Static tipping kg lb kg lb kg lb kg lb kg lb kg lbload full turn 23.5R25 9500 20944 9200 20283 8950 19731 8650 19070 8400 18519 7750 17086750/65R25 9850 21716 9550 21054 9250 20393 8950 19731 8700 19180 8000 17637L120E Pallet fork tines, straight. Break out, capacity 5900 kg / 13007 lb, 600 mm/2'0" per armGround mm ft in mm ft in mm ft in mm ft in mm ft in mm ft incondition 500 1'8'' 600 2'0'' 700 2'4'' 800 2'8'' 900 2'11'' 1200 3'11''Rough terrain kg lb kg lb kg lb kg lb kg lb kg lb23.5R25 5800 12787 5650 12456 5450 12015 5300 11684 5150 11354 4750 10472750/65R25 6000 13228 5800 12787 5650 12456 5450 12015 5300 11684 4900 10803Firm and level ground kg lb kg lb kg lb kg lb kg lb kg* lb*23.5R25 7700 16976 7450 16424 7200 15873 7000 15432 6800 14991 5900 13007750/65R25 7950 17527 7700 16976 7450 16424 7250 15983 7000 15432 5900 13007Static tipping kg lb kg lb kg lb kg lb kg lb kg lbload full turn 23.5R25 9500 20944 9200 20283 8950 19731 8650 19070 8400 18519 7750 17086750/65R25 9850 21716 9550 21054 9250 20393 8950 19731 8700 19180 8000 17637L120E Pallet fork tines, visibility optimized right/left, capacity 3900 kg / 8598 lb, 600 mm/2'0" per armGround mm ft in mm ft in mm ft in mm ft in mm ft in mm ft incondition 500 1'8'' 600 2'0'' 700 2'4'' 800 2'8'' 900 2'11'' 1200 3'11''Rough terrain kg lb kg lb kg lb kg lb kg lb kg* lb*23.5R25 5800 12787 5650 12456 5450 12015 5300 11684 5150 11354 3900 8598750/65R25 6000 13228 5800 12787 5650 12456 5450 12015 5300 11684 3900 8598Firm and level ground kg lb kg lb kg* lb* kg* lb* kg* lb* kg* lb*23.5R25 7700 16976 7450 16424 6650 14661 5850 12897 5200 11464 3900 8598750/65R25 7950 17527 7700 16976 6650 14661 5850 12897 5200 11464 3900 8598Static tipping kg lb kg lb kg lb kg lb kg lb kg lbload full turn 23.5R25 9500 20944 9200 20283 8950 19731 8650 19070 8400 18519 7750 17086750/65R25 9850 21716 9550 21054 9250 20393 8950 19731 8700 19180 8000 17637L120E Lumber fork tines, straight, capacity 4875 kg / 10747 lb, 600 mm/2'0" per armGround mm ft in mm ft in mm ft in mm ft in mm ft in mm ft incondition 500 1'8" 600 2'0" 700 2'4" 800 2'8" 900 2'11" 1200 3'11"Rough terrain kg lb kg lb kg lb kg lb kg lb kg lb23.5R25 5800 12787 5650 12456 5450 12015 5300 11684 5150 11354 4750 10472750/65R25 6000 13228 5800 12787 5650 12456 5450 12015 5300 11684 4850* 10692*Firm and level ground kg lb kg lb kg lb kg lb kg* lb* kg* lb*23.5R25 7700 16976 7450 16424 7200 15873 7000 15432 6500 14330 4850 10692750/65R25 7950 17527 7700 16976 7450 16424 7250 15983 6500 14330 4850 10692Static tipping kg lb kg lb kg lb kg lb kg lb kg lbload full turn 23.5R25 9500 20944 9200 20283 8950 19731 8650 19070 8400 18519 7750 17086750/65R25 9850 21716 9550 21054 9250 20393 8950 19731 8700 19180 8000 17637L120E Stone fork**Ground mm ft incondition 600 2'0"Rough terrain kg lb23.5R25 6550 14440Firm and level ground kg lb23.5R25 8650 19070Static tipping kg lbload full turn 23.5R25 10750 23700*) Limited by the attachment**) Loader equipped with logging counterweight and L5 tires76
Fork attachmentsPallet fork frameVisibility optimized.For material handling. Can be combined with differentfork tines.b fc fL110E/L120Ea fAttachment codeOrder No.a fFrame width mm ft inb fFrame height mm ft inc fFrame length mm ft inFrame weight kg lbPAFF H801091500 4'11''800 2'7''320 1'1''290 640PAFF H936852200 7'3''800 2'7''320 1'1''390 860Pallet fork tinesStraight, digging depth optimized.For use in combination with the above fork frames.The fork tines are marked in accordance with relevantSwedish and international standards. Specified maximumload applies at a load center distance of 600 mm/2'0".Note: The order number is for one fork tine only.The tines cannot be used on frames with forkpositioner.L110E Standard Heavy dutyAttachment codeOrder NoMax. load per tine kg lbs tTine length mm ft int tTine height mm ft inu tTine width mm ft inv tTine thickness mm ft inx tWidth over tine top mm ft inz tTine length mm ft inTine weight kg lbA Reach at min. lift mm ft inB Max. reachposition mm ft inC Height at min. lift mm ft inD Height at max.reach position mm ft inE Height at max. lift mm ft inF Reach at max. lift mm ft inPAFT STD936884300 94801200 3'11''940 3'1''150 0'6''60 0'2.4''180 0'7''1320 4'4''140 310870 2'10''165022183037807705'5''0'.9''6'0''12'5''2'6''PAFT STD801084300 94801450 4'9''940 3'1''150 0'6''60 0'2.4''180 0'7''1560 5'2''160 350870 2'10''165022183037807705'5''0'.9''6'0''12'5''2'6''PAFT STD830134300 94801830 6'0"940 3'1"150 0'6"60 0'2.4"180 0'7"1940 6'4"180 400870 2'10"165021184037807705'5"0'.6"6'0"12'5"2'6"PAFT HD803425900 130101200 3'11''950 3'1''150 0'6''70 0'2.8''180 0'7''1330 4'4''160 340880 2'11''166020184037807805'5''0'.8''6'0''12'5''2'7''t tx tu ts tz tPAFT HD803435900 130101450 4'9''950 3'1''150 0'6''70 0'2.8''180 0'7''1580 5'2''180 390880 2'11''166020184037807805'5''0'.8''6'0''12'5''2'7''v tLumber forktinesLUFT STD801934875 107471200 3'11''930 3'1''250 0'10''50 0'2''300 1'0''1310 4'3''190 420860 2'10''164071179037307605'4''0'2.8''5'10''12'3''2'6''L120E Standard Heavy dutyAttachment codeOrder NoMax. load per tine kg lbs tTine length mm ft int tTine height mm ft inu tTine width mm ft inv tTine thickness mm ft inx tWidth over tine top mm ft inz tTine length mm ft inTine weight kg lbA Reach at min. lift mm ft inB Max. reachposition mm ft inC Height at min. lift mm ft inD Height at max.reach position mm ft inE Height at max. lift mm ft inF Reach at max. lift mm ft inPAFT STD936884300 94801200 3'11''940 3'1''150 0'6''60 0'2.4''180 0'7''1320 4'4''140 310970 3'2''172029184038508105'8''0'1.1''6'0''12'7''2'8''PAFT STD801084300 94801450 4'9''940 3'1''150 0'6''60 0'2.4''180 0'7''1560 5'2''160 350970 3'2''172029184038508105'8''0'1.1''6'0''12'7''2'8''PAFT STD830134300 94801830 6'0"940 3'1"150 0'6"60 0'2.4"180 0'7"1940 6'4"180 400970 3'2"172027184038508105'8"0'1.1"6'0"12'8"2'8"PAFT HD803425900 130101200 3'11''950 3'1''150 0'6''70 0'2.8''180 0'7''1330 4'4''160 340980 3'2''173027184038508205'8''0'1.1''6'0''12'8''2'8''PAFT HD803435900 130101450 4'9''950 3'1''150 0'6''70 0'2.8''180 0'7''1580 5'2''180 390980 3'2''173027184038508205'8''0'1.1''6'0''12'8''2'8''Lumber forktinesLUFT STD801934875 107471200 3'11''930 3'1''250 0'10''50 0'2''300 1'0''1310 4'3''190 420960 3'2''171078179038008005'7''0'3.1''5'10''12'6''2'8''77
Fork attachmentsPallet fork tinesVisibility optimized right/left.For use in combination with the fork frames on page 77.The fork tines are marked in accordance with relevantSwedish and international standards. Specified maximumload applies at a load center distance of 600 mm/2'0".Note: The order number is for one fork tine only.The tines cannot be used on fork frames with forkpositioner.t tx tu ts tz tv tLumber fork tinesL110E L120E L110E L120EAttachment codeRight and left fork tineOrder NoMax. load per tine kg lbs tTine length mm ft int tTine height mm ft inu tTine width mm ft inv tTine thickness mm ft inx tWidth over tine top mm ft inz tTine length mm ft inTine weight kg lbA Reach at min. lift mm ft inB Max. reachposition mm ft inC Height at min. lift mm ft inD Height at max.reach position mm ft inE Height at max. lift mm ft inF Reach at max. lift mm ft inPAFT OFFR L93686/93687390012008801506021013201408701650-331890384077086003'11''2'11''0'6''0'2.4''0'8''4'4''3002'10''5'5''-0'1.3''6'2''12'7''2'6''PAFT OFFR L80106/801073900 86001450 4'9''880 2'11''150 0'6''60 0'2.4''210 0'8''1570 5'2''150 340870 2'10''1650-35189038407705'5''-0'1.4''6'2''12'7''2'6''PAFT OFFR L93686/936873900 86001200 3'11''880 2'11''150 0'6''60 0'2.4''210 0'8''1320 4'4''140 300970 3'2''1720-26189039008105'8''-0'1''6'2''12'10''2'8''PAFT OFFR L80106/80107390014508801506021015701509701720-281890390081086004'9''2'11''0'6''0'2.4''0'8''5'2''3403'2''5'8''-0'1.1''6'2''12'10''2'8''LUFT OFFR L80344/803453900 86001200 3'11''870 2'10''250 0'10''50 0'2''300 1'0''1310 4'3''190 410860 2'10''164016184037907605'4''0'.6''6'0''12'5''2'6''LUFT OFFR L80344/803453900 86001200 3'11''870 2'10''250 0'10''50 0'2''300 1'0''1310 4'3''190 410960 3'2''171023184038508005'7''0'.9''6'1''12'8''2'8''78
Fork attachmentsSubframe, 80192 for Lumber fork tines, floatingFor use in combination with fork frame 80109, 93685 and80191 Combi fork frame.u tAttachment codeOrder Nos tSubframe length mm ft int tSubframe height mm ft inu tSubframe width mm ft inv tVertical movementof the tine in subframe mm ft inSubframe weight kg lbL110E/L120ESUBFRAME80192150 0'6''670 2'2''365 1'2''120600'5''132t ts tv txtLumber fork tines, floating for Subframe 80192The fork tines are marked in accordance with relevantSwedish and international standards. Specified maximumload applies at a load center distance of 600 mm/2'0''.Note: The order number is for one fork tine only.L110EL120Et tztstutvtAttachment codeOrder NoMax. load per tine kg lbs tTine length mm ft int tTine height mm ft inu tTine width mm ft inv tTine thickness mm ft inx tWidth over tine top mm ft inz tTine length mm ft inTine weight kg lbA Reach at min. lift mm ft inB Max. reachposition mm ft inC Height at min. lift mm ft inD Height at max.reach position mm ft inE Height at max. lift mm ft inF Reach at max. lift mm ft inLUFT FLO801944875 107471200 3'11''930 3'1''250 0'10''50 0'2''370 1'2''1340 4'5''185 410859 2'10''163888177037147645'4''0'3''5'10''12'2''2'6''LUFT FLO801944875 107471200 3'11''930 3'1''250 0'10''50 0'2''370 1'2''1340 4'5''185 410956 3'2''171395177037808045'7''0'4''5'10''12'5''2'8''Figures based on the forks’ lowest postion in thesubframe.79
Fork attachmentsFork frame with side shift and fork positionerFork frame is ideal for cases where the width of the loadvaries. The fork tines can be hydraulically adjusted to thewidth of the load. Assembly components are included.b fa fNote: Requires 3 rd and 4 th hydraulic function.Note: Fork tines are not included in the order number.c fo min – o maxL110E/120EAttachment code FFPSS H FFPSS HOrder No 80335 80336Oa fb fc fminmaxFrame widthFrame heightFrame lengthFrame weightmmmmmmmmmmkgft inft inftft inft inlb300120015008003203701'0"3'11"4'11"2'7"1'1"820300170020008003404501'0"5'7"6'7"2'7"1'2"990Side shift tinesStraight (for frame order No. 80335–80336)There are three types of tines for use with the side shift forkframes. Note that excessively long fork tines can damagegoods located behind the load when picking up and settingdown. The fork tines are marked in accordance with existingSwedish and international standards. Specified max. loadapplies at a load center distance of 600 mm/2'0".Note: The order number is for one fork tine only.L110E/L120EAttachment codeRight or leftOrder NoMax. load per tine kg lbs tTine length mm ft int tTine height mm ft inu tTine width mm ft inv tTine thickness mm ft inx tWidth over tine top mm ft inz tTine length mm ft inTine weight kg lbSSFTR L80806/ 808074300 94821200 3'11"940 3'1"150 0'6"60 0'2"270 0'11''1340 4'5''150 330SSFTR L80804/808054300 94821450 4'9"940 3'1"150 0'6"60 0'2"270 0'11''1590 5'3"170 375t tx tA Reach at min. lift mm ft inB Max. reach position mm ft inC Height at min. lift mm ft inD Height at max.reach position mm ft inE Height at max. lift mm ft inF Reach at max. lift mm ft in870165020183037807702'10"5'5"0'1"6'0"12'5"2'6"970172030184038508103'2"5'8"0'1"6'0"12'8"2'8"z tu tv ts t80
Fork attachmentsFork tine extensionsFor straight fork tines and off-set fork tines.Intended for handling light materials.Note: The order number is for one fork tine extensiononly.L110E/L120Es tu tv tAttachment codePAFT EXT HOrder No. 99444Tine size mm ft in 150 x 60 0'6''x 0'2''Allowable load per tine1250 mm, 4'1" from frame kg lb 2100 4630s tTine length mm ft in 2500 8'2"u tTine width mm ft in 200 0'8"v tTine thickness mm ft in 90 0'4"Tine weight kg lb 70 150Separate fork back rest extendedNote: The order number is for one back rest extensiononly.hL110E/L120EAttachment codeOrder No.h Height mm ft inWeight kg lbBACK REST808732150 7'1"35 77Stone forkA heavy duty fork with fixed tines designed for block handling,e.g. granite blocks, marble blocks, etc.Specified max. load applies at a load center distance of600 mm/2'0".a sAttachment codeOrder No.Max. load per tine kg lba sFork width mm ft inb sFork height mm ft inc sFork length mm ft ind sTine width mm ft ine sWidth over fork tine mm ft ins sTine length mm ft int sTine thickness mm ft inFork weight kg lbL110E/L120EPAFF/PAFT H914209900 218301300 4'3''990 3'3''1450 4'9''160 0'6''1160 3'10''1220 4'0''110 0'4.3''580 1280b sc se sdss st s81
Fork attachmentsCombi-forks with one-piece clampWith the specially designed one-piece top clamp, theCombi-fork is perfect for handling palletized goods orroundwood in applications where the load must besecured.Fork tines are not included and must be orderedseparately.Volvo recommends the heavt duty fork tines shown onpage 75. Specified max. load applies at a load centerdistance of 600 mm / 2'0''.Note: Requires 3 rd hydraulic function.L110EL120EAttachment codeOrder NoA area m 2 ft 2Rated operating load*)s cFork witdth mm ft int cFork height mm ft inu cFork length mm ft inFork weight kg lbHHeight at max. lift mm ft inI Overall operatingheightmm ft inK Opening height mm ft inL Minimum clamp width mm ft inM Maximum load heigth mm ft inCOF OPC H801910,4–1,5 4.3–16.1175019101690113037805620312034022905'9''6'3''5'7''249012'5''18'5''10'3''1'1''7'6''COF OPC H801910,4–1,5 4.3–16.1175019101690113038505700312034022905'9''6'3''5'7''249012'8''18'8''10'3''1'1''7'6''t cs cu c*) Rated operating load capacitiesRetained load:(retained by the top clamp)Recommended max. load:L110E 6250 kg 13780 lbL120E 7200 kg 15870 lbRefers to a loader equipped with logging counterweight.82
Material handling armGeneralHigh capacity is needed for work with material handlingarm due to the heavy stresses on the arm, machine andhydraulics. Different types of material handling arms aremade for the different Volvo wheel loaders, optimally suitedto each loader. Powerful hydraulics and a lift-armsystem with ample breakout torque, even in the top position,enables the load to be maneuvered with perfectcontrol in all situations.When it comes to work with material handling arms andsecure control over the load, Volvo wheel loaders are ina class of their own. Few competitors can even comeclose to the loads that Volvo wheel loaders are approvedto lift.Safety requirementsPeople are often present in the working area whena material handling arm is being used. Authoritiestherefore, impose very strict requirements on wheelloaders equipped with material handling arms.Max. rollbackpositionMaterial handling arm specifications on the followingpages are calculated for machines with tires:L110E – 23.5 R25L120E – 23.5 R25Max.reachpositionMaterial handling arm, 3-sectionThe material handling arm is used on construction sitesfor pipelaying etc. It has two telescopic sections withbuilt-in mechanical stops to prevent overextension.Max. rolloutpositionL110EL120EAttachments codeOrder Not Length, fully retracted mm ft inu Arm height mm ft inx Arm width mm ft inArm weight kg lbAllowable loads*A Op. load at full turn + max. reach, min. length kg lbB Op. load at full turn + max. reach, middle length kg lbC Op. load at full turn + max. reach, max length kg lbD Reach at max. lift + max. rollback, max. length mm ft inE Reach at max. lift + max. rollback, middle length mm ft inF Reach at max. lift + max. rollback, min. length mm ft inG Reach at max. reach, min. length mm ft inHReach at max. reach, middle length mm ft inI Reach at max. reach, max. length mm ft inJ Reach at min. lift + max. rollout, min. length mm ft inK Reach at min. lift + max. rollout, middle length mm ft inL Reach at min. lift + max. rollout, max. length mm ft inM Height at min. lift + max. rollout, min. length mm ft inN Height at min. lift + max. rollout, middle length mm ft inO Height at min. lift + max. rollout, max. length mm ft inP Height at tipping pos., all lengths mm ft inQ Height at max. lift + max. rollback, min. length mm ft inR Height at max. lift + max. rollback, middle length mm ft inS Height at max. lift + max. rollback, max. length mm ft in* According to EN 474-3 tipping load utilization is 50%MHA H MECH920082050 6'9''840 2'9''1160 3'10''500 110033002570210027402120150032204350549013101880245019002970395016205350631072507300567046508'12''6'11''4'11''10'7''14'3''18'0''4'4''6'2''8'0''6'3''9'9''12'12''5'4''17'7''20'8''23'9''MHA H MECH920082050 6'9''840 2'9''1160 3'10''500 110036502850234028502200156032904430556013601900245020203000401016205400634072708050628051609'4''7'3''5'1''10'10''14'6''18'3''4'6''6'3''8'0''6'8''9'10''13'2''5'4''17'9''20'10''23'10''uxt83
Material handling armMaterial handling arm, hydraulic foldingThe material handling arm has one telescopic section andcan be folded down hydraulically as well. It is used on worksites where loads have to be lowered below ground levelor where obstacles have to be bypassed. The arm is equippedwith a line rupture valve and the folding section can belowered at a restricted rate.Note: Requires 3 rd hydraulic function.Max. rollbackpositionxCMax.reachpositionutMax. rolloutpositionAttachments codeOrder Not Length, fully retracted mm ft inu Arm height mm ft inx Arm width mm ft inArm weight kg lbAllowable loads*A Op. load at full turn + max. reach, min. length kg lbC Op. load at full turn + max. reach, max length kg lbD Reach at max. lift + max. rollback, max. length mm ft inF Reach at max. lift + max. rollback, min. length mm ft inG Reach at max. reach, min. length mm ft inI Reach at max. reach, max. length mm ft inJ Reach at min. lift + max. rollout, min. length mm ft inL Reach at min. lift + max. rollout, max. length mm ft inM Height at min. lift + max. rollout. min. length mm ft inO Height at min. lift + max. rollout. max. length mm ft inP Height at tipping pos., all lengths mm ft inQ Height at max. lift + max. rollback, min. length mm ft inS Height at max. lift + max. rollback, max. length mm ft in* According to EN 474-3 tipping load utilization is 50%L110EMHA H FOLD821373250 10'8''840 2'9''1160 3'10''570 12502480208027502200450055001940245031103970160064107250547045909'10''7'3''14'9''18'1''6'4''8'10''10'2''13'0''5'3''21'0''23'9''L120EMHA H FOLD821373250 10'8''840 2'9''1160 3'10''570 12602740231028602300457055701960244031504030160064407260604050909'5''7'7''15'1''18'3''6'5''8'10''10'4''13'3''5'3''21'2''23'10''84
Other attachmentsAttachments for special applicationsTo further extend the versatility of Volvo wheel loaders,we have adapted attachments made by other manufacturersto suit our products. This makes it easier for ourcustomers to select the attachment that yields the bestwork results with Volvo wheel loaders. Attachments matchedto specific wheel loaders guarantee an effec-tivecombination.Detailed specifications and other informa-tion can be obtained from the respective manufacturer(Allied Supplier) or local distributor, see last page.NOTE: When ordering an attachment please state the OrderNo. for the adapter and the hose set as well.Crate and pallet rotator, Bolzoni Auramo360°-rotating unit for emptying and/or turning of cratesand pallets.Note: Requires 3 rd and 4 th hydraulic functions.L110E/L120EclType of mountingHOrder No. Bolzoni AuramoKG F4 F6 AOrder No. Adapter 414670-01Order No. Hose set411900-60-ACapacity – Loader center distance kg/mm lb/ft in 2200/500Opening range:a min. – a max. mm ft in 630-1960Weight clamp kg lb 970Weight adapter kg lb 180c Frame width mm ft in 970ll Lost load distance mm ft in 321l Fork length mm ft in 1200o Fork height mm ft in 560x Adapter thickness mm ft in 1204845/1'8"2'0.8"–6'5.1"21404003'2.2"1'0.6"3'11.2"1'10"0'5"lla min. – a max.oxAdapterDrum rotator, Bolzoni Auramo360°-rotating unit for emptying of liquids and powders indrums.Note: Requires 3 rd and 4 th hydraulic functions.cL110E/L120EType of mountingHOrder No. Bolzoni AuramoKG-10 T2 AOrder No. Adapter 414670-01Order No. Hose set411900-60-ACapacity – Loader center distance kg/mm lb/ft in 1000/320Opening range:a min. – a max. mm ft in 460–1560Weight clamp kg lb 445Weight adapter kg lb 180c Frame witdth mm ft in 870ll Lost load distance mm ft in 231l Arm length mm ft in 470n Arm height mm ft in 240x Adapter thickness mm ft in 1202205/1'0.6"1'6.1"–5'1.4"9804002'10.2"0'9.1"1'6.6''0'9.6"0'5"llla min. – a max.nxAdapter85
Other attachmentsFork clamp, Bolzoni Auramo360° rotating for emptying and/or turning boxes anddrums.Note: Requires 3 rd and 4 th hydraulic functions.cL110E/L120EType of mountingHOrder No. Bolzoni AuramoKG-22 H6A EUOrder No. Adapter 414670-01Order No. Hose set411900-60-ACapacity – Loader center distanceOpening range:kg/mm lb/ft in 2200/500 4845/1'7"a min. – a max.Weight clampWeight adapterc Frame widthll Lost load distancemmkgkgmmmmft inlblbft inft in560–185052618011002851'10"–6'1"11604003'7"0'11"l Fork length mm ft in 1200 3'11"x Adapter thickness mm ft in 1150'4"llxlAdaptera min. – a max.Bale clamp for pulp waste paper bales, Bolzoni AuramoClamp for handling of pulp waste paper bales, etc. Strong,slender bale arms ensure secure grip and dense stacking.Built-in pressure reduction and side shift.llcNote: Requires 3 rd and 4 th hydraulic functions.nL110E/L120Ela amin. max.Type of mountingOrder No. Bolzoni AuramoHBA-50PFOrder No. Adapter 414670-02Order No. Hose set413250-60-ACapacity – Load center distance kg/mm lb/ft in 5000/800Rated operating load kg*) lb*) 5000Opening range:a min. – a max. mm ft in 730–2560Weight clamp kg lb 1510Weight adapter kg lb 300c Frame width mm ft in 1600ll Lost load distance mm ft in 260l Arm length mm ft in 1200n Arm height mm ft in 490x Adapter thickness mm ft in 19011020/2'7"110202'5"–8'5"33256605'3"0'10"3'11"1'7"0'7"xAdapter*) Refers to operation on firm and level ground86
Other attachmentsRotating reel clamp, Bolzoni Auramo180°-rotating reel clamp for handling of upright orhorizontal paper reels with diameters up to 1800 mm/5'9''. Slender arm profile and gentle clamp blades withmaintenance-free friction surface facilitate handling. Builtinpressure reduction.Note: Requires 3 rd and 4 th hydraulic functions.l 1llcamax.amin.l 2nL110E/L120EType of mountingHOrder No. Bolzoni AuramoRA-500 NJOrder No. Adapter 414670-02Order No. Hose set413250-60-ACapacity – Load center distance kg/mm lb/ft in 5000–800Rated operating load kg*) lb*) 5000Diameter range:a min. – a max. mm ft in 500–1600Weight kg lb 1390Weight adapter kg lb 300c Frame width mm ft in 1340ll Lost load distance mm ft in 235n Arm height mm ft in 1300l 1Arm length mm ft in 790l 2Arm length mm ft in 1300x Adapter thickness mm ft in 19012115–2'7"110101'8"–5'3"30606604'5"0'9"4'3"2'7"4'3"0'7"xAdapter*) Referse to operation on firm and level groundAdapter to convert any Bolzoni Auramostandard clamp with ISO-2328 mounting class toVolvo Wheel Loader Hook-on mounting.Order No. Bolzoni Auramofor aggregate with 3A mounting class:for aggregate with 4A mounting class:LMF–3ALMF–4A87
Other attachmentsDiagonal snow blade, HOLMS TKHPThe TKHP plow features horizontal oscillation and longitudinalangle adjustment, and is recommended for snowclearance on roads, parking lots etc.The blade has a reversible cutting edge divided into sectionsthat fold back when they encounter small obstaclessuch as manhole covers. Hydraulically adjustable 35°right or left and equipped with horizontal oscillation withvariable ground pressure for road-hugging performance.Can be equipped with rubber cutting edge.Note: Requires 3 rd hydraulic function.L110E/L120EHOLMS TKHP 4,0Type of mountingHWorking width angled 30° mm ft in 3300 10'10"Weight kg lb 1060 2340a Plow width mm ft in 4000 13'1"b Plow height mm ft in 1000 3'3"baVee plow, HOLMS KHVThe KHV can be adjusted from a ”V” shape to a ”A” shapeand anything in between. It is ideal for applicationssuch as gradually opening a snowblocked road or collectingand pushing away snow at junctions, on car parksetc.Each side is individually adjustable by means of hydrauliccylinders and has mechanical stops at the endpositions.The pressure of the plow on the road surface can beeasily adjusted to the requirements of every situation.The snow plow is equipped with a resilient cutting edgethat folds back when it contacts fixed obstacles such asmanhole covers. There is also a hydraulic shock valvethat opens if the pressure against one of the plow-halvesbecomes too high, such as in case of contact with solidobstacles. The shock valve is connected to a pressureaccumulator, thus there’s no need for any return line tothe hydraulic oil tank.Note: Requires 3 rd and 4 th hydraulic function or 3 rd andelectrohydraulic selector option with diagonaloperation + 3 rd function.Requires single-acting lift function.L110E/L120EFor more information please contact:Holms Industri ABBox 924SE-591 29 MotalaSwedenPhone: +46 141-22 41 00Fax: +46 141-22 41 90e-mail: info@holms.comwww.holms.comHOLMSKHV 3,6 KHV 4,0Type of mountingHHWeight kg lb 865 1907 930 2050Overall width mm ft in 3600 11'10" 4000 13'1"Height mm ft in 1000 3'3" 1000 3'3"No. of foldable cutting edges 4 4Sides individually adjustable Yes YesWorking width at 30° angling mm ft in 3100 10'2" 3500 11'6"Electro-hydraulic selectoroption for folding* Order No. 243350 243350*) Eliminates the need of fourth function88
Other attachmentsSweeper, HOLMS SHFor street cleaning when the debris does not have to becollected. Can be equipped with water tank and spraynozzle bank for dust reduction.The sweeper is mounted on the wheel loader’s attachmentbracket and the hydraulic hoses are connected viaquick-couplings to the loader’s 3 rd hydraulic function, orin certain cases both the 3 rd and 4 th hydraulic function.The sweeper has a large cylinder diameter and a uniquebalanced suspension that eliminates the need for supportwheels, allowing higher sweeping speed.The suspension provides constant, evenly distributedpressure against the ground surface, and thus the machineis not affected by rough surfaces such as curbs, railroadtracks, etc. Excellent suspension minimizes brushwear.Two hydraulic motors drive the sweeper. Direct drive giveshigh efficiency and low maintenance costs.The front brush protector is vertically adjustable, great fordifferent needs.Easily replaceable brush segments of polypropylene ormixed 50/50 polypropylene and steel.Two parking supports for stable parking of the sweeper.Control alternative for angling 30° in either direction:Mechanical, Hydraulic and Electro-hydraulic.The sweeper is standard-equipped with hydraulic functionfor angling 30° in either direction. Electro-hydraulic angleadjustment is offered as an optional function. This requiresonly a 3 rd hydraulic function, which makes it possibleto adjust the angle during operation.Can be equipped with different options as 600 l/158 US gal,watering system, side shift etc.Note: Requires 3 rd hydraulic function.4 th hydraulic function is required if the optional functionfor electro-hydraulic angling of the brush is notselected.For more information please contact:Holms Industri ABBox 924SE-591 29 MotalaSwedenPhone: +46 141-22 41 00Fax: +46 141-22 41 90e-mail: info@holms.comwww.holms.comL110E/L120EHOLMS SH 3,0 SH 3,5Type of mountingHHWeight kg 530 560Working width mm lb 3000 1170 3500 1235Working width angled 30° mm ft in 2600 9'10'' 3000 11'6''Brush diameter mm ft in 900 8’6’’ 900 9’10’’Oil flow:Maximum l/minft in210*2'11''210*2'11''Minimum l/min US gpm 70 55* 70 55*US gpm18.518.5Electro-hydraulic angling Order No. 242745 2427453 rd function lever lock detent Order No. 244622 244622*) Must be used with HOLMS Flow restrictor part No. 244750 in combination with Volvo*) retaining function89
Other attachmentsPick-up Sweeper, HOLMS 300The sweeper is a hydraulically driven pick-up sweeperwhich has been adapted for front mounting on the wheelloader’s attachment bracket. It is connected with a quickcouplingto the loaders’s 3 rd hydraulic function.A unique suspension system eliminates the need for supportwheels and allows high speed operation.Water sprinkler equipment with a 400 liter/106 US galwater tank and electrically driven pump.The sweeper is driven by two direct-acting hydraulicmotors.Note: Requires 3 rd hydraulic function.If the kit for adustable oil flow has been selected(3 rd hydraulic function), then lever lock is notrequired.L110E/L120EHOLMS 300 3,0Type of mountingHWeight empty kg lb 690 1520Effective debris volume l US gal 700 185Working width mm ft in 3000 9'10"Brush cyl. diameter mm ft in 700 2'3"Oil flow:Maximum* l/min US gpm 210* 55.5*Minimum l/min US gpm 70 18.5Lever lock, detent Order No. 80098Side brush, left Order No. 243380Side brush, right Order No. 243840Side brush, dual mounted Order No. 244165*) Must be used with HOLMS Flow restrictor part No. 244750 in*) combination with Volvo retaining functionThe HOLMS 300 can be equipped with a side brush,mounted on the left or right hand side, dual mounted isalso available. For sweeping by curbstones, walls etc.For more information please contact:Holms Industri ABBox 924SE-591 29 MotalaSwedenPhone: +46 141-22 41 00Fax: +46 141-22 41 90e-mail: info@holms.comwww.holms.com90
Allied suppliersTo further extend the range of use for our machines, wehave concluded agreements with certain suppliers, knownas ”Allied Suppliers”, concerning attachments of strategicinterest. These attachments are adapted to and authorizedfor Volvo Wheel Loaders. This makes it easier for ourcustomers to select attachments that yield the best workresults together with our machines.ALWAYS check with the sales company /factory for the current approved andauthorized suppliers.Detailed specifications and other information is availablefrom either respective local distributors/dealers,or the factory.Bolzoni Auramo –Paper handling and other attachmentsfor Volvo Wheel LoadersHolms Industri AB –Sweepers, snow clearanceattachments and sand-spreadingbuckets for Volvo Wheel LoadersUlrich Attachments, Ltd.Multi-purpose and side dumpbuckets for Volvo Wheel LoadersManufacturer:Auramo OyP-O Box 78F-01511 VaantaFinlandPhone: +358 (9) 82931Fax: +358 (9) 870 1037Manufacturer:Holms Industri ABBox 924SE-591 29 MotalaSwedenPhone: +46 141-22 41 00Fax: +46 141-22 41 90e-mail: info@holms.comwww.holms.comManufacturer:Conspec HouseSt Andrews Way Inudstrial EstateBicester RoadAylesburyBuckinghamshire HP19 3AFEnglandPhone: +44 (0)1296 422995Fax: +44 (0)1296 42284991
Notes........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................92
Ref. No. 21 A 100 1272 EnglishPrinted in Sweden 2004.06–1,0 WLOVolvo, Eskilstuna
Change language