Saunier-Duval-Thema-Classic-F24e-Installation-manual

More documents

Recommendations

Info

7 Fixing JigThe fixing jig is made up as follows:A - Heating return fitting with isolating valve.B (F24E Only) - Cold water inlet fitting with isolatingvalve (m). The cold water inlet restrictor supplied withboiler is fitted when the boiler is installed. Refer toSection 9.C - Heating flow fitting with isolating valve.D (F24E Only) - Domestic hot water outlet.E - Gas service cock.Other components within the fixing jig pack.F - Hanging bracketG - wall templateJ - sealing washers and screwsF24E shownDiagram 7.14000124050-218
8.1 Cutting the flue hole• Remove the wall template, follow the instructions given on thewall template.• Position the wall template, taking due regard of the minimumclearances for the selected flue application, see diagram 8.1.• Rear hole cutting• Mark correct position of Top Rear flue outlet hole fromtemplate, then remove template, before cutting, for use, later.• Side hole cutting• Mark the horizontal centre line for the hole on the rear wall.Extend the horizontal centre line to the side wall and mark thevertical centre line of flue hole as shown in diagram 8.1.IMPORTANT NOTE: When cutting the flue hole and whenextending the flue centre line to a side wall, remember that theflue system must have a fall of about 35mm per metre of fluedownward towards the terminal. There MUST never be adownward incline towards the boiler.• Making allowance for the slope of the flue, cut hole in externalwall, preferably using a core drill. For installations with internaland external access use a 105mm diameter core drill.• For installations with internal access only use a 125 mmdiameter core drill.8 Piping System Installation8.2 Fixing jig, refer to diagram 7.1• IMPORTANT NOTE: Ensure that the hanging bracket is fittedto a flat and true wall area for correct alignment with the boiler.Side Flue - Check the horizontal centre line and reposition thetemplate if necessary.Rear Flue - Reposition the wall template over the hole in wall.• Mark the securing position holes.• Check that the hanging bracket is level.• Drill, plug and secure the bracket to the wall, using suitablescrews (not supplied) for the wall type and capable of supportingthe total weight of the appliance (refer to wall template for fixingpoints).8.3 Water connectionIMPORTANT NOTE: Do not subject the isolating valves to heatfrom blowlamp, when making connection.Connect the system pipework to the fixing jig connection pipesand the fixing jig isolating valves, observing the correct flow andreturn as shown in diagram 8.1.8.4 Gas connectionGas Safety (Installation and use) RegulationsIn your interests and that of gas safety, it is the law that ALL gasappliances are installed and serviced by a competent personin accordance with the above regulations.• The whole of the gas installation, including the meter, shouldbe inpected, tested for soundness and purged in accordancewith the current issue of BS6891 and in IE the current editionof I.S.813 "Domestic Gas Installations".F24E shownDiagram 8.119 4000124050-2
Page 1 and 2: To be left with the user4000124050-
Page 3 and 4: ContentsCONTENTS DESCRIPTION SECTIO
Page 5 and 6: Draining and FillingCaution: The bo
Page 7: User Controls and LightingCentral h
Page 10 and 11: Programmer Instructions for UseEven
Page 12 and 13: 1 Technical DataThe F24E and F18E S
Page 14 and 15: 3 Heating System Design3.1 Bypass
Page 16 and 17: 5 Boiler Schematic F24E1 - Fan.2 -
Page 20 and 21: 9 Boiler Installation9.1 Sheet meta
Page 22 and 23: 10 Horizontal Telescopic Top Flue I
Page 24 and 25: 18410a Horizontal Top Flue Installa
Page 26 and 27: 11.3 Mains Voltage External Control
Page 28 and 29: 112 Commissioning5. • Bleed each
Page 30 and 31: 15 Routine Cleaning and InspectionR
Page 32 and 33: 15 Routine Cleaning and Inspection9
Page 34 and 35: 16 Fault FindingBefore trying to op
Page 36 and 37: 16 Fault FindingFAULT: NO HEATINGAr
Page 38 and 39: 16 Fault FindingF1 FAULT DISPLAYEDF
Page 40 and 41: 17 Wiring Diagram F24EgorFANg/yOVER
Page 42 and 43: 18 Replacement of PartsTo Drain the
Page 44 and 45: 18 Replacement of Parts18.9 Burner
Page 46 and 47: 18 Replacement of Parts230V CONTROL
Page 48 and 49: 18.25 System water pressure sensor,
Page 50 and 51: 18 Replacement of Parts18.32 (F24E
Page 52: 19 Spare partsWhen ordering spare p

Saunier-Duval-Thema-Classic-F24e-Installation-manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?