Saunier-Duval-Thema-Classic-F24e-Installation-manual

More documents

Recommendations

Info

5 Boiler Schematic F24E1 - Fan.2 - Air pressure switch.3 - Heat exchanger.4 - Overheat thermostat.5 - Combustion chamber.6 - Expansion vessel.7 - Flame sense electrode.8 - Burner.9 - Ignition electrode.10 - Pump.11 - Heating thermistor.12 - Ignition unit.13 - By-pass.14 - Gas control valve.15 - Loss of water sensor.16 - Domestic heat exchanger17 - 3 way valve18 - Domestic water flow sensor19 - Filter cold water inlet20 - Filling system21 - Discharge safety valve (3bar)22 - Drain valve23 - Heating filterFITTED TOREAR OFAPPLIANCE9899A - Heating returnB - Cold water inletC - Heating flowD - Domestic hot water outletE - Gas5a Boiler Schematic F18E SBDiagram 5.11 - Fan.2 - Air pressure switch.3 - Heat exchanger.4 - Overheat thermostat.5 - Combustion chamber.6 - Expansion vessel.7 - Flame sense electrode.8 - Burner.9 - Ignition electrode.10 - Pump.11 - Heating thermistor.12 - Ignition unit.13 - By-pass.14 - Gas control valve.15 - Loss of water sensor.16 - Heating filter.17 - Discharge safety valve (3bar).A - Heating return.B - Heating flow.C - Gas.FITTED TOREAR OFAPPLIANCE11450A B CDiagram 5a.14000124050-216
6 Boiler Location, Flue and Ventilation6.1 Boiler LocationThe recommended clearances are shown in diagram 6.1.Note: The boiler must be mounted on a flat wall which issufficiently robust to take its weight when full. If in doubt, expertadvice should be obtained, in the event of the wall being foundnot suitable.The minimum acceptable spacings from the terminal toobstructions, other terminals and ventilation openings areshown in diagram 6.2. For Ireland the minimum distances forthe flue terminal positionning must be those detailed in I.S.813"Domestic Gas <strong>Installation</strong>s".The boiler must be installed so that the terminal is exposed tothe external air.6.2 Terminal guard, see diagram 6.3.A terminal guard is required if persons could come into contactwith the terminal or the terminal could be subject to damage.If a terminal guard is required, it must be positioned to providea minimum of 50mm clearance from any part of the terminaland to be central over the terminal.A suitable terminal guard type K3 can be supplied by:Tower flue components Ltd.Morley roadTonbridgeKentTN9 1RA6.3 Flue optionsThere are various flue systems to choose from as follows:Horizontal telescopic top flue pack.Horizontal top flue pack.Vertical flue pack.Twin flue pack.Extensions, 90° and 45° bends.For detailed information refer to flue options guide. This isavailable from your nearest stockist.6.4 Cupboard or compartment ventilationThe boiler can be fitted in a cupboard or compartment withoutthe need for permanent ventilation.11652*Note: It is permissible toinstall the boiler with smallerclearances than those quotedPROVIDING that considerationis given for Servicing/Repairs.25mmaboveelbow20mm* 5mm 600mm20mm* 450mm * 5mm300mmDiagram 6.1MINIMUM SITING DIMENSIONS FOR THEPOSITIONING OF FLUE TERMINALSMMHORIZONTAL FLUESA DIRECTLY BELOW, ABOVE ORHORIZONTALLY TO AN OPENING, AIR BRICK,OPENING WINDOWS, AIR VENT, OR ANYOTHER VENTILATION OPENING 300B BELOW GUTTER, DRAIN/SOIL PIPE 75C BELOW EAVES 200D BELOW A BALCONY OR CAR PORT 200E FROM VERTICAL DRAIN PIPES ANDSOIL PIPES 150F FROM INTERNAL/EXTERNAL CORNERSOR TO A BOUNDARY ALONGSIDE THETERMINAL 300G ABOVE ADJACENT GROUND ORBALCONY LEVEL 300H FROM SURFACE OR A BOUNDARYFACING THE TERMINAL 600I FACING TERMINALS 1200JFROM OPENING (DOOR/WINDOW)IN CAR PORT INTO DWELLING 1200K VERTICAL FROM A TERMINAL 1500L HORIZONTALLY FROM A TERMINAL 300VERTICAL FLUESM FROM ADJACENT WALL TO FLUE 300N FROM ANOTHER TERMINAL 600P FROM ADJACENT OPENING WINDOW 1000Q ABOVE ROOF LEVEL 300Diagram 6.211508Diagram 6.317 4000124050-2
Page 1 and 2: To be left with the user4000124050-
Page 3 and 4: ContentsCONTENTS DESCRIPTION SECTIO
Page 5 and 6: Draining and FillingCaution: The bo
Page 7: User Controls and LightingCentral h
Page 10 and 11: Programmer Instructions for UseEven
Page 12 and 13: 1 Technical DataThe F24E and F18E S
Page 14 and 15: 3 Heating System Design3.1 Bypass
Page 18 and 19: 7 Fixing JigThe fixing jig is made
Page 20 and 21: 9 Boiler Installation9.1 Sheet meta
Page 22 and 23: 10 Horizontal Telescopic Top Flue I
Page 24 and 25: 18410a Horizontal Top Flue Installa
Page 26 and 27: 11.3 Mains Voltage External Control
Page 28 and 29: 112 Commissioning5. • Bleed each
Page 30 and 31: 15 Routine Cleaning and InspectionR
Page 32 and 33: 15 Routine Cleaning and Inspection9
Page 34 and 35: 16 Fault FindingBefore trying to op
Page 36 and 37: 16 Fault FindingFAULT: NO HEATINGAr
Page 38 and 39: 16 Fault FindingF1 FAULT DISPLAYEDF
Page 40 and 41: 17 Wiring Diagram F24EgorFANg/yOVER
Page 42 and 43: 18 Replacement of PartsTo Drain the
Page 44 and 45: 18 Replacement of Parts18.9 Burner
Page 46 and 47: 18 Replacement of Parts230V CONTROL
Page 48 and 49: 18.25 System water pressure sensor,
Page 50 and 51: 18 Replacement of Parts18.32 (F24E
Page 52: 19 Spare partsWhen ordering spare p

Saunier-Duval-Thema-Classic-F24e-Installation-manual

Create successful ePaper yourself

Delete template?

Save as template?