Saunier-Duval-Thema-Classic-F24e-Installation-manual

More documents

Recommendations

Info

Programmer Instructions for UseEvent ReviewTo review the programs at any time, press Prog. key. Events willappear in the order they were entered with repeated presses ofthe Prog. key. After all events have been reviewed, the blankdisplay will appear to allow entering another event. Anotherpress of the Prog. key will display the number of free eventsavailable, such as Fr 16 if 4 events have been entered.Manual OverrideWhile in the Run Mode, pressing the key once will reversethe current mode; ON to OFF or OFF to ON. The symbolappears in the display to indicate a temporary override.At the next scheduled switching time, automatic controlresumes, eliminating the override.CONTINUOUS OPERATION: While in the Run Mode, pressthe key twice to turn the output to permanently ON.symbol appears in display.Pressing the key three times will turn the output OFFpermanently. symbol appears in display.To terminate a continuous override, press the key untilappears in the display.Changing an EventSelect the event to be changed with the Prog. key. A new setof days may be selected with the Day key just as in initialprogramming.Hours and minutes can be changed with the h and m keys.Press Prog. or key to store the new programme.Deleting an EventTo delete only one or a few events: Press Prog. key until thedesired program is displayed.Press m key to :59 and press once more to blank out.Press h key to 11PM and press once more to blank out.Press key, display will flash for several seconds and thenenter the Run Mode. Using the reset key will delete ALL events,the time of day, and day of the week.TroubleshootingPROBLEM: Days are flashing, pressing any key does nothingexcept key turns output ON and OFF.SOLUTION: Time of Day and Day of Week have not been set.See "SETTING THE TIME"This is the condition after a reset. If the timer is found in thiscondition after it has been installed, programmed and operatingfor a while, it may indicate that interference has disrupted themicroprocessor causing a loss of programme information.A second, but very unlikely cause of loss of programme is apower failure with the backup capacitor low or dead. Check bydisconnecting power and monitoring how long the capacitorkeeps the time of day in the display. Typically, the capacitor willmaintain the time and programmes for 4 days, but not morethan 5 days.PROBLEM: Time of day was set while holding the keydown, but days are still flashing.SOLUTION: Current day of week was not set while holdingdown the key. See "SETTING THE TIME"PROBLEM: It is 10AM and an ON event for 8AM was entered,but the output is not ON. Display shows the andsymbols.SOLUTION: After programming, the timer does not "look back"to determine if it should be ON. Press the key (temporaryoverride) to turn the output ON; appears in display.The timer will assume automatic operation at the nextprogrammed event.PROBLEM: An event for 8AM Monday through Friday wasentered,but it will not accept it and is flashing.SOLUTION: The ON or OFF was not entered as partof the program. ON or OFF must be selected.4000124050-210
1 Technical DataHeatingHeat input (max) NET QHeat input (min) NET QHeat output (max) NET P26,94 kW91,200 BTU/H9,91 kW33,820 BTU/H23,6 kW81,550 BTU/HHeat output (min) NET P8,9 kW30,370 BTU/HEfficiency - Sedbuk D 78,3%Maximum heating temperature87° CExpansion vessel effective capacity5 litresExpansion vessel charge pressure0,5 barMaximum system capacity at 75°C110 litresSafety valve,maximum service pressure 3 barHot waterHeat input (max) NET QHeat input (min) NET Q26,94 kW91,200 BTU/H9,91 kW33,820 BTU/HHeat output (max) NET P23,6 kW81,550 BTU/HHeat output (min) NET P8,9 kW30,370 BTU/HMaximum hot water temperature 60 °CMinimum hot water temperature 38 °CSpecific flow rate (for 35°C temp rise) 9,8 litres/min.Threshold flow rate1,7 litres/min.Maximum supply pressure10 barMinimum supply pressure0,5 barCombustionProducts outlet diameterFresh air inlet diameterCombustion products valuesElectricalElectrical supplyElectrical ratingLevel of protectionFuse ratingF24E60 mm100 mmCO (60 ppm)CO2 (6,7%)NOx (48ppm)230 V ~ 50Hz122 W fused at 3AIPX4D125mAHeatingHeat input (max) NET QHeat input (min) NET QHeat output (max) GROSS PHeat output (min) GROSS P21,9 kW74,722 BTU/H11 kW37,532 BTU/H19,8 kW67,556 BTU/H9,2 kW31389 BTU/HEfficiency - Sedbuk D 78,8%Maximum heating temperatureExpansion vessel effective capacityExpansion vessel charge pressureMaximum system capacity at 75°CSafety valve,CombustionProducts outlet diameterFresh air inlet diameterCombustion products valuesElectricalElectrical supplyElectrical ratingLevel of protectionFuse ratingNatural Gas (G20)Ø Burner injectorInlet pressureMaxi. Burner pressureMini. Burner pressureF18E SB87° C5 litres0,5 bar110 litresmaximum service pressure 3 bar60 mm100 mmCO (30 ppm)CO2 (5,9%)NOx (76 ppm)230 V ~ 50Hz122 W fused at 3AIPX4D1,25mA1,2 mm20 mbar8,82 mbar2,25 mbarGas rate maximum 2,3 m 3 /hNatural Gas (G20)Ø Burner injector1,2 mmInlet pressure20 mbarMaxi. Burner pressure12,2 mbarMini. Burner pressure2,25 mbarGas rate maximum 2,74 m 3 /hGas rate minimum 1,16 m 3 /hButane Gas (G30)Ø Burner injectorInlet pressureMaxi. Burner pressureMini. Burner pressureGas rate maximumGas rate minimumPropane Gas (G31)Ø Burner injectorInlet pressureMaxi. Burner pressureMini. Burner pressureGas rate maximumGas rate minimum0,73 mm29 mbar23,2 mbar4,41 mbar2,01 kg/h0,87 kg/h0,73 mm37 mbar29,8 mbar5,4 mbar2,01 kg/h0,83 kg/hButane Gas (G30)Ø Burner injectorInlet pressureMaxi. Burner pressureMini. Burner pressureGas rate maximumGas rate minimumPropane Gas (G31)Ø Burner injectorInlet pressureMaxi. Burner pressureMini. Burner pressureGas rate maximumGas rate minimum0,73 mm29 mbar17,65 mbar4,41 mbar1,72 kg/h0,87 kg/h0,73 mm37 mbar22,52mbar5,4 mbar1,70 kg/h0,83 kg/h11 4000124050-2
Page 1 and 2: To be left with the user4000124050-
Page 3 and 4: ContentsCONTENTS DESCRIPTION SECTIO
Page 5 and 6: Draining and FillingCaution: The bo
Page 7: User Controls and LightingCentral h
Page 12 and 13: 1 Technical DataThe F24E and F18E S
Page 14 and 15: 3 Heating System Design3.1 Bypass
Page 16 and 17: 5 Boiler Schematic F24E1 - Fan.2 -
Page 18 and 19: 7 Fixing JigThe fixing jig is made
Page 20 and 21: 9 Boiler Installation9.1 Sheet meta
Page 22 and 23: 10 Horizontal Telescopic Top Flue I
Page 24 and 25: 18410a Horizontal Top Flue Installa
Page 26 and 27: 11.3 Mains Voltage External Control
Page 28 and 29: 112 Commissioning5. • Bleed each
Page 30 and 31: 15 Routine Cleaning and InspectionR
Page 32 and 33: 15 Routine Cleaning and Inspection9
Page 34 and 35: 16 Fault FindingBefore trying to op
Page 36 and 37: 16 Fault FindingFAULT: NO HEATINGAr
Page 38 and 39: 16 Fault FindingF1 FAULT DISPLAYEDF
Page 40 and 41: 17 Wiring Diagram F24EgorFANg/yOVER
Page 42 and 43: 18 Replacement of PartsTo Drain the
Page 44 and 45: 18 Replacement of Parts18.9 Burner
Page 46 and 47: 18 Replacement of Parts230V CONTROL
Page 48 and 49: 18.25 System water pressure sensor,
Page 50 and 51: 18 Replacement of Parts18.32 (F24E
Page 52: 19 Spare partsWhen ordering spare p

Saunier-Duval-Thema-Classic-F24e-Installation-manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?