SurgiGuide Cookbook - Dental-Depot

More documents

Recommendations

Info

14. Measure the blended powder and the liquid. Mix well with a spatula. Apply thismixture in the area of the teeth impressions, close the flask and apply pressure.*15. This mixture needs to harden under a press for about 45 minutes to 1 hour. Bariumsulfate slows down the hardening of the artificial resin.*16. When the resin has completely hardened, remove it from the flask. Place the model inan articulator to check the occlusion and make any necessary adjustments.17. Remove the prosthesis from the model. Note that some of the excess resin mixedwith barium sulfate will have flowed out over the base plate. Remove this excessbarium sulfate mixture from the plate. Only the barium sulfate filling the teeth shouldremain.PROTOCOL36www.SimPlant.comSurgiGuide Cookbook
18. You may polish the prosthesis to improve its appearance for the patient.19. When ordered by the surgeon, holes can be drilled into the middle of the cingulum(anterior) and in the middle of the occlusal planes (molars and pre-molars), parallelwith the direction of the teeth. These holes will provide the surgeon with a clearreference as to where to place the implants.20. Optionally, the name of the patient can be inserted into the denture.PROTOCOL* Off course, dedicated preformed radiopaque teeth can also be used for this purpose, in thatregard, it is not needed to make a mixture of cold polymerising resin and barium sulfate. Ifchosen for this solution, the protocol might slightly differ.37www.SimPlant.comSurgiGuide Cookbook
Page 9 and 10: IntroductionIntroductionSurgiGuide
Page 11: OverviewStep 1: DiagnosisIt all sta
Page 15 and 16: DiagnosisStep 1: DiagnosisClear inf
Page 17 and 18: Minimal Invasive SurgeryThe exact p
Page 19 and 20: Step 3: Taking the the 3D scanNo sc
Page 21 and 22: Step 4: Conversion ofStep 4: Conver
Page 24 and 25: Step 6: Ordening SurgiGuide and the
Page 26: 2. Types of SurgiGuide drill guides
Page 29 and 30: SAFE SystemThe SAFE System is used
Page 31 and 32: Step 7: DeliveryStep 7: Delivery an
Page 33: Protocols & SurgicalproceduresSurgi
Page 36 and 37: Procedure to fabricate a standard s
Page 40 and 41: Procedure to make a scan prosthesis
Page 42 and 43: Aligning the patient• For correct
Page 44 and 45: General scanning instructions• Se
Page 46 and 47: As another example: the remarks fie
Page 48 and 49: After choosing a SurgiGuide type, t
Page 51 and 52: Requirements of a plaster castThe s
Page 53 and 54: Scan prosthesisIf a scan prosthesis
Page 55 and 56: Intact and recent cast in plasterSe
Page 57 and 58: Surgical Procedure: Bone-supported
Page 59 and 60: 2. Positioning of the SurgiGuideCor
Page 61: 4. Subsequent drill(s)Proceed with
Page 64 and 65: Pre-operative actions1. Fit of the
Page 66 and 67: CoolingPrecautions should be taken
Page 69 and 70: Surgical Procedure: Procedure: Toot
Page 71 and 72: Surgical Procedure1. Decision on th
Page 73: 4. Subsequent drill(s)Proceed with
Page 76 and 77: Planning actionsTo achieve full adv
Page 78 and 79: 5. Perform all regular checks for S
Page 80 and 81: 3. Punching/TrephineIf a transmucos
Page 82 and 83: 8. Implant placementScrew the corre
Page 84 and 85: DISLCAIMER OF LIABILITYMaterialise
Page 86 and 87: Preparing the temporary prosthesis1
Page 88 and 89:
Implant Surgery and Providing an Im
Page 90:
Contact us:Materialise US - Clinica
show all

SurgiGuide Cookbook - Dental-Depot

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?