Installation Operation Maintenance

More documents

Recommendations

Info

InstallationUnit nameplateThe unit nameplate gives thecomplete model reference numbers.The unit power rating is shown, andpower supplies should not deviateby more than 5% from the ratedpower. Compressor motoramperage is shown in box I.MAX.The customer's electricalinstallation must be able towithstand this current.Installation instructionsFoundationsNo special foundations are required,provided the supporting surface isflat and level, and can withstand theweight or the unit.Isolating rubber pads6 pads are supplied as standardwith the machine (55x150mm).They should be placed between thesupporting floor and the unit toisolate from the ground. Trane doesnot recommend to install springisolators.Water drain holeInstall a drain hole wide enough todrain away water from the unit inthe event of shut-down or repair.ClearanceRespect recommended clearancearound the unit to allowmaintenance operation to take placewithout obstruction. For minimumclearance, consult the certifiedsubmittals, which are available onrequest from your Trane Agency.Note for RTCA remote condenser:When determining unit placement,give careful consideration toensuring a sufficient flow of airacross the condenser heat-transfersurface. The unit must be positionedso that the airflow through thecondensing coils is not hindered byany obstacle. The condensing coilsmust be protected from side windswhen their speed exceeds 16 km/h.• Position the unit above theaverage height of snowobserved in the region where itis installed.• Never install temporary orpermanent objects (tarp or roof)over the unit, because recyclingof hot air would reduce thecapacity of the condensing coils.• Discharged air from the fansmust not be obstructed. It isprohibited to install ducts for thefan discharge air (even shortones). This is because the fanssupplied on standard units donot generate any additionalstatic pressure.10CG-SVX06A-E4
InstallationHandlingA specific lifting method isrecommended as follows:1. 4 lifting points are built into theunit.2. Slings and spreader bar to beprovided by rigger and attachedto the 4 lifting points.3. Minimum rated lifting capacity(vertical) of each sling andspreader bar shall be no lessthan the tabulated unit shippingweight. Refer to Figures 1 and 2CAUTION: This unit must be liftedwith the outmost care. Avoid shockload by lifting slowly and evenly. Toprevent any damage, position thelifting bar so that the slings do nottouch the unit.Figure 1 - Rigging the unit - CGWN - CCUNABCDCG-SVX06A-E411
Page 1 and 2: InstallationOperationMaintenanceInd
Page 3: ContentsGeneral informationForeword
Page 6 and 7: General DataTable 3 - Water cooled
Page 8 and 9: General DataTable 5 - Evaporator hy
Page 12 and 13: InstallationFigure 2 - Rigging the
Page 14 and 15: InstallationMinimal installation wa
Page 16 and 17: InstallationFigure 4 - CCUN hydraul
Page 18 and 19: InstallationFigure 6 - CCUN hydraul
Page 20 and 21: Installation1. Pressure gauges: sho
Page 22 and 23: InstallationThe minimum required su
Page 24 and 25: InstallationPressure relief valve -
Page 27 and 28: InstallationWhen ordered, the outdo
Page 29: InstallationOperating rangeCAUTION:
Page 32 and 33: General Start-upStart-upFollow the
Page 34 and 35: General Start-upCAUTION:For the war
Page 36 and 37: General Start-upFigure 23 - High ef
Page 38 and 39: General Start-upFigure 27 - Evapora
Page 40 and 41: General Start-upFigure 31 - Evapora
Page 42 and 43: General Start-upFigure 35 - Condens
Page 44 and 45: General Start-upThe correction fact
Page 46 and 47: OperationControl and unit operation
Page 48 and 49: MaintenanceAnnual preventive visit
Page 50 and 51: MaintenanceF) Compressor noisyCompr
Page 52: Literature Order Number CG-SVX06A-E

Installation Operation Maintenance

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?