Attention! Your ePaper is waiting for publication!
By publishing your document, the content will be optimally indexed by Google via AI and sorted into the right category for over 500 million ePaper readers on YUMPU.
This will ensure high visibility and many readers!
Индастриал Технолоджис www.industrial‐technologies.com.ua +38 044 498 21 94OptionsGreasing Hole[Grease Nipple and Greasing Hole for Models SHW and SRS]Models SHW and SRS do not have a grease nipple as standard. Installation of a grease nipple andthe drilling of a greasing hole is performed at <strong>THK</strong>. When ordering SHW and SRS, indicate that thedesired model requires a grease nipple or greasing hole. (For greasing hole dimensions and supportedgrease nipple types and dimensions, see Table1.)When using SHW and SRS under harsh conditions, use QZ Lubricator* (optional) or Laminated ContactScraper LaCS* (optional).Note1) Grease nipple is not available for models SHW12, SHW14, SRS5M, SRS5WM, SRS7M, SRS7WM, SRS9M,SRS9WM, SRS12M and SRS12WM. They can have a greasing hole.Note2) Using a greasing hole other than for greasing may cause damage.Note3) For QZ Lubricator*, see A1-345. For Laminated Contact Scraper LaCS*, see A1-335.Note4) When desiring a grease nipple for a model attached with QZ Lubricator, contact <strong>THK</strong>.EEnd sealLEnd sealFig.1 Dimensions of the Grease Nipple for Model SHWEEnd sealLEnd sealFig.2 Dimensions of the Grease Nipple for Model SRSNote) For the L dimension, see the corresponding specificationtable.Table1 Table of Grease Nipple and Greasing Hole DimensionsUnit: mmModel No. EGrease nipple orgreasing hole12 — φ2.2 drilled hole14 — φ2.2 drilled hole17 5 PB107SHW 21 5.5 PB1021B27 12 B-M6F35 12 B-M6F50 16 B-PT1/85M — φ0.8 drilled hole5WM — φ0.8 drilled hole7M — φ1.2 drilled hole7WM — φ1.2 drilled hole9 M/N — φ1.5 drilled hole9 WM/WN — φ1.6 drilled holeSRS 12 M/N — φ2.0 drilled hole12 WM/WN — φ2.0 drilled hole15 M/N 4.0(5.0) PB10715 WM/WN (5.0) 4.0PB10720M 3.5(5.0) PB10725M 4.0(5.5) PB1021BNote) Figures in the parentheses indicate dimensions withouta seal.<strong>LM</strong> <strong>Guide</strong> (Options)<strong>Industrial</strong> <strong>Technologies</strong>A1-361
Индастриал Технолоджис www.industrial‐technologies.com.ua +38 044 498 21 94Maximum resistance for LiCSUnit: NSSRModel No.Maximum resistance forLiCS15X 120X 1.125X 1.630X 1.635X 2SRG 15 0.7Note) The value indicates the sliding resistance of two LiCSunits per <strong>LM</strong> block and does not include the slidingresistances of the <strong>LM</strong> block and the side seals.<strong>Industrial</strong> <strong>Technologies</strong>A1-360
Индастриал Технолоджис www.industrial‐technologies.com.ua +38 044 498 21 94OptionsGreasing Hole[Grease Nipple and Greasing Hole for Models SHW and SRS]Models SHW and SRS do not have a grease nipple as standard. Installation of a grease nipple andthe drilling of a greasing hole is performed at <strong>THK</strong>. When ordering SHW and SRS, indicate that thedesired model requires a grease nipple or greasing hole. (For greasing hole dimensions and supportedgrease nipple types and dimensions, see Table1.)When using SHW and SRS under harsh conditions, use QZ Lubricator* (optional) or Laminated ContactScraper LaCS* (optional).Note1) Grease nipple is not available for models SHW12, SHW14, SRS5M, SRS5WM, SRS7M, SRS7WM, SRS9M,SRS9WM, SRS12M and SRS12WM. They can have a greasing hole.Note2) Using a greasing hole other than for greasing may cause damage.Note3) For QZ Lubricator*, see A1-345. For Laminated Contact Scraper LaCS*, see A1-335.Note4) When desiring a grease nipple for a model attached with QZ Lubricator, contact <strong>THK</strong>.EEnd sealLEnd sealFig.1 Dimensions of the Grease Nipple for Model SHWEEnd sealLEnd sealFig.2 Dimensions of the Grease Nipple for Model SRSNote) For the L dimension, see the corresponding specificationtable.Table1 Table of Grease Nipple and Greasing Hole DimensionsUnit: mmModel No. EGrease nipple orgreasing hole12 — φ2.2 drilled hole14 — φ2.2 drilled hole17 5 PB107SHW 21 5.5 PB1021B27 12 B-M6F35 12 B-M6F50 16 B-PT1/85M — φ0.8 drilled hole5WM — φ0.8 drilled hole7M — φ1.2 drilled hole7WM — φ1.2 drilled hole9 M/N — φ1.5 drilled hole9 WM/WN — φ1.6 drilled holeSRS 12 M/N — φ2.0 drilled hole12 WM/WN — φ2.0 drilled hole15 M/N 4.0(5.0) PB10715 WM/WN (5.0) 4.0PB10720M 3.5(5.0) PB10725M 4.0(5.5) PB1021BNote) Figures in the parentheses indicate dimensions withouta seal.<strong>LM</strong> <strong>Guide</strong> (Options)<strong>Industrial</strong> <strong>Technologies</strong>A1-361
Change language