OAKTON pH 10 manual 8/00 rev - Oakton Instruments

More documents

Recommendations

Info

Table of Contents1. Introduction ..............................................................................Page 4Getting started • Maintenance, troubleshooting2. Display and keypad functions.................................................Page 53. Preparation...............................................................................Page 6• Inserting the batteries • Connecting the electrode andtemperature probe • Attaching the electrode holder to themeter • Inserting the electrode into the electrode holder• Connecting the AC adapter4. pH calibration ...........................................................................Page 8• 1-point pH calibration • 2- or 3-point pH calibration5. pH measurement....................................................................Page 10• Measurement with Automatic Temperature Compensation• Measurement with Manual Temperature Compensation6. mV measurement...................................................................Page 127. HOLD feature .........................................................................Page 138. Temperature calibration........................................................Page 14• 1-point temperature calibration • Two point temperaturecalibration9. Electrode care and maintenance .........................................Page 17• Storage • After measuring • To reuse the electrodeElectrode cleaning • Reactivating the electrode10. Error messages.....................................................................Page 1911. Troubleshooting....................................................................Page 2012. Specifications........................................................................Page 2013. Accessories ...........................................................................Page 2114. Warranty ................................................................................Page 2215. Return of items......................................................................Page 22Page 2Page 3
1. IntroductionThank you for selecting an OAKTON ® meter. The OAKTON ® pH 10 seriesmeters are economical, microprocessor-based meters that deliver high ±0.01 pHaccuracy. They also read millivolts for taking ORP measurements. The pH 10 hasmany user-friendly features that are completely accessible through the waterresistantmembrane keypad.Getting started (sections 1 to 8)To perform the basic functions of this meter, read sections 1 through 8 of thismanual. These sections include basic instructions (about keypad functions,connecting the electrodes, calibration, taking readings, etc.) that will get you upand running quickly.Maintenance, troubleshooting, etc (sections 9 to 15)The remaining sections of the manual deal with electrode maintenance, errormessages, and troubleshooting. This part of the manual also includes theSpecifications, Accessories, Warranty, and Return of Items sections.2. Display and Keypad functionsThe water-resistant membranekeypad makes the instrument easyMEAS CAL CONto use. Each button, whenpHpressed, has a correspondingREADYHOLDmVgraphic indicator on the large liquidcrystal display. The LCD has apHprimary and secondary display.ERR°CATCThe primary display shows thereadings for pH and mV. Thesecondary display shows thetemperature readingspH Temp mVsimultaneously with the primary display. Both the primary and secondarydisplays show special indicators such as error messages, measurement units,and modes of operation.Keypad functions (see Figure A).ON/OFF Powers the unit on and shuts the unit off.Meter directly enters measurement mode when youONOFFturn it on.HOLD Freezes the measured readings. To activate,press HOLD while in pH or mV mode. To release,press HOLD again.HOLD MODEMODE Selects the parameter of measurement. pH isCALMEASthe default mode. Pressing MODE lets you scroll first toCONtemperature mode, then to mV mode, then back to pHmode again.NOTE: Temperature mode is used for temperaturecalibration; temperature readings are alwaysdisplayed on the secondary display.ACAL/MEAS Enters CAL mode for the calibrationfunction. You can access CAL only in the pH or temperature modes. pH buffervalues are 4.01, 7.00, and 10.01. To end calibration and return to measurementmode, press CAL/MEAS again. Press OFF to end all functions. To confirmcalibration, press the CON key.▲ Use to scroll up the buffer calibration values provided by the calibrationprogram. It will scroll one value up from the present calibration value displayedon the LCD with each key press. When the highest calibration value is reached,it will scroll around to the lowest value.▼ Similar to ▲, except with each key press, the value scrolls one step down.CONPress CON to confirm the calibration point. “CON” will flash on the screen.Page 4Page 5
Page 1: Operating InstructionsOAKTON ® pH
Page 5 and 6: 4. pH CalibrationThis instrument is
Page 7: 6. mV measurement7. HOLD featureThe
Page 11 and 12: 11. TroubleshootingProblem Cause So
Page 13: DISTRIBUTED BY:

OAKTON pH 10 manual 8/00 rev - Oakton Instruments

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?