HTI Manual - Desert Tactical Arms
HTI Manual - Desert Tactical Arms HTI Manual - Desert Tactical Arms
• Allow to sit for 15 minutes.• Push patch through wet with Shooter’s Choice.• Patch with 4 dry patches or until patches come out dry and clean.• Run patch through bore wet with Sweet’s 7.62 bore solvent and let sit forNO LONGER than 10 minutes.• Patch with a clean dry patch. If there is blue residue on the patch, repeatthe cleaning process until no blue residue remains on the final stage.• Once the bore is clean, utilize the pull through with patch saturated withShooter’s Choice in a back and forth motion for 10 strokes.• Push through 4 dry patches or until patches come out dry and clean.403. Muzzle Brake: Ensure that the vents are clear of debris and occasionally checkto ensure the brake has not “shot loose”.4. Magazine: It is imperative that the magazine be given the best of care and keptin perfect condition. They should be disassembled, cleaned, and lightly oiled(see pages 19-21). Check magazine lips. They should not be deformed, nicked,or cracked.
5. Receiver Interior: A visual and manual inspection of the inside of the receiverwill reveal what, if any cleaning is necessary. Most debris can be removed witha cloth, cleaning patch, or cleaning brush.6. Bolt Face: Ensure that the bolt face is free from debris that will create headspace,chambering problems, and/or inhibit function of either the extractor orejector. This area can be wiped clean or blown out. This is also a good time toensure that the ejector and the extractor are functioning properly by manuallyactuating them to ensure proper spring function and return. Also, a small amountof Break Free may be applied to the bolt face area at this time.7. Bolt Interior: The operator should occasionally remove the firing pin assemblyfrom the bolt (see pages 44-48). Wipe this area clean prior to applying a smallamount of Break Free.8. General Cleaning: The entire rifle should be wiped off with a clean cloth lightlysaturated with Break Free on occasion. This includes the barreled action, scoperings, and ancillary components.41
- Page 3 and 4: For video instructions see our webs
- Page 5 and 6: CARE AND CLEANING..................
- Page 7 and 8: Before shooting the rifle:• Alway
- Page 9 and 10: SIGHTSPicatinny rail (no taper)BARR
- Page 11 and 12: CompactRuggedThe HTI’s bullpup de
- Page 13 and 14: Other Benefits• The full length M
- Page 15 and 16: DISASSEMBLY AND ASSEMBLY1. This cha
- Page 17 and 18: REMOVING BARREL1. Remove buttpad an
- Page 19 and 20: 3. Make sure the barrel is fully se
- Page 22 and 23: 6. Ease the spring and follower out
- Page 24 and 25: REMOVING STOCK PANELS221. Place the
- Page 26 and 27: LOADING AND UNLOADINGINSERTING THE
- Page 28 and 29: UNLOADING (CLEARING) THE HTI1. Plac
- Page 30 and 31: ADJUSTING CHEEK PIECE1. With an 5mm
- Page 32 and 33: 6. Install ring tops.7. Finger tigh
- Page 34 and 35: QUICK ZEROING1. Find the center of
- Page 36 and 37: 344. Once on paper, shoot a three s
- Page 38 and 39: It is easier to train yourself to s
- Page 40 and 41: INITIAL CLEANING1. Upon receipt of
- Page 44 and 45: BEFORE AND AFTER FIRINGCLEANING BEF
- Page 46 and 47: ADDITIONAL DISASSEMBLY & AS-SEMBLYB
- Page 48 and 49: BOLT ASSEMBLY1. Insert the firing p
- Page 50 and 51: 5. Hold the bolt with the end cap f
- Page 52 and 53: 2. MAGAZINE NOT EMPTY (Malfunction)
- Page 54 and 55: B. FAILURE TO CHAMBER * Bolt does n
- Page 56 and 57: 4. Fouled Extractor5. Extractor Def
- Page 58 and 59: PARTS EXPLODED VIEWHTI56BarrelBoltR
- Page 60 and 61: MAGAZINE58Floor PlateFollowerMagazi
- Page 62 and 63: PATENTS PENDINGNo part of this docu
• Allow to sit for 15 minutes.• Push patch through wet with Shooter’s Choice.• Patch with 4 dry patches or until patches come out dry and clean.• Run patch through bore wet with Sweet’s 7.62 bore solvent and let sit forNO LONGER than 10 minutes.• Patch with a clean dry patch. If there is blue residue on the patch, repeatthe cleaning process until no blue residue remains on the final stage.• Once the bore is clean, utilize the pull through with patch saturated withShooter’s Choice in a back and forth motion for 10 strokes.• Push through 4 dry patches or until patches come out dry and clean.403. Muzzle Brake: Ensure that the vents are clear of debris and occasionally checkto ensure the brake has not “shot loose”.4. Magazine: It is imperative that the magazine be given the best of care and keptin perfect condition. They should be disassembled, cleaned, and lightly oiled(see pages 19-21). Check magazine lips. They should not be deformed, nicked,or cracked.