HTI Manual - Desert Tactical Arms
HTI Manual - Desert Tactical Arms HTI Manual - Desert Tactical Arms
LOADING AND UNLOADINGINSERTING THE MAGAZINESafety OnSafety Off241. Clear the rifle (see page 26).2. Set the fire selector on “S” (Safe) (fig.19).Figure 193. Push the magazine catch lever fowardwhile firmly incerting the magazine.Release the magazine catch lever tofully lock the magazine into position(fig. 20). Above the magazine wellthere is an indicator window that iffully covered with a metal tab yourmagazine is properly incerted.Figure 20
FIRING THE HTI1. Never chamber a round until you areready to fire.2. Set fire selector to “F” (Fire) (fig. 19).3. Lift bolt handle and slide it all the wayrearward (fig. 21).4. Run bolt forward and lock into place.5. The rifle is now ready to fire with around chambered.Figure 216. Pull the trigger to fire the gun.7. Repeat step 3. The empty case isejected. If there is another cartridgein the magazine, it will be loaded intothe chamber when running the boltforward. The gun is loaded and ready tofire again.CAUTION: After the last shot is fired the bolt must remain open. Ensure the cartridgechamber is empty!25
- Page 3 and 4: For video instructions see our webs
- Page 5 and 6: CARE AND CLEANING..................
- Page 7 and 8: Before shooting the rifle:• Alway
- Page 9 and 10: SIGHTSPicatinny rail (no taper)BARR
- Page 11 and 12: CompactRuggedThe HTI’s bullpup de
- Page 13 and 14: Other Benefits• The full length M
- Page 15 and 16: DISASSEMBLY AND ASSEMBLY1. This cha
- Page 17 and 18: REMOVING BARREL1. Remove buttpad an
- Page 19 and 20: 3. Make sure the barrel is fully se
- Page 22 and 23: 6. Ease the spring and follower out
- Page 24 and 25: REMOVING STOCK PANELS221. Place the
- Page 28 and 29: UNLOADING (CLEARING) THE HTI1. Plac
- Page 30 and 31: ADJUSTING CHEEK PIECE1. With an 5mm
- Page 32 and 33: 6. Install ring tops.7. Finger tigh
- Page 34 and 35: QUICK ZEROING1. Find the center of
- Page 36 and 37: 344. Once on paper, shoot a three s
- Page 38 and 39: It is easier to train yourself to s
- Page 40 and 41: INITIAL CLEANING1. Upon receipt of
- Page 42 and 43: • Allow to sit for 15 minutes.•
- Page 44 and 45: BEFORE AND AFTER FIRINGCLEANING BEF
- Page 46 and 47: ADDITIONAL DISASSEMBLY & AS-SEMBLYB
- Page 48 and 49: BOLT ASSEMBLY1. Insert the firing p
- Page 50 and 51: 5. Hold the bolt with the end cap f
- Page 52 and 53: 2. MAGAZINE NOT EMPTY (Malfunction)
- Page 54 and 55: B. FAILURE TO CHAMBER * Bolt does n
- Page 56 and 57: 4. Fouled Extractor5. Extractor Def
- Page 58 and 59: PARTS EXPLODED VIEWHTI56BarrelBoltR
- Page 60 and 61: MAGAZINE58Floor PlateFollowerMagazi
- Page 62 and 63: PATENTS PENDINGNo part of this docu
LOADING AND UNLOADINGINSERTING THE MAGAZINESafety OnSafety Off241. Clear the rifle (see page 26).2. Set the fire selector on “S” (Safe) (fig.19).Figure 193. Push the magazine catch lever fowardwhile firmly incerting the magazine.Release the magazine catch lever tofully lock the magazine into position(fig. 20). Above the magazine wellthere is an indicator window that iffully covered with a metal tab yourmagazine is properly incerted.Figure 20