HIMax Safety Manual - Tuv-fs.com

More documents

Recommendations

Info

5 System Bus Module HIMaxWARNINGPhysical injury possible!SILworX must be used to verify the parameterization.Proceed as follows:• In SILworX, log in to the system module located in Base Plate 0, Slot 2.• In SILworX, log in to the system module on Base Plate 1, Slot 2.• Check the Control Panels of both system bus modules to ensure that the"responsible" attribute has only been set for the correct system bus module (seeFigure 1 and Figure 2)!Recommended Configurations:• If processor modules are only contained on Base Plate 0, both system bus modules onBase Plate 0 must be set to 'responsible' (Figure 1).• If processor modules are also contained on Base Plate 1 (Figure 2), the followingsystem bus modules must be set to 'responsible'.- on Base Plate 0, the system bus module in Slot 1.- on Base Plate 1, the system bus module in Slot 2.Base Plate 0: Base Plate 0R System Bus Module set to ResponsibleBase Plate 1: Base Plate 1Figure 1: Recommended Configuration: All Processor Modules on Base Plate 0Page 26 of 70HI 801 003 D Rev.2.0
HIMax5 System Bus ModuleBase Plate 0: Base Plate 0R System Bus Module set to ResponsibleBase Plate 1: Base Plate 1Figure 2: Recommended Configuration: Processor Modules on Base Plate 0 and on BasePlate 1HI 801 003 D Rev.2.0 Page 27 of 70
Page 1: SAFETYHIMax ®Safety Manual
Page 4 and 5: Table of contentsHIMax3.5 Certifica
Page 6 and 7: Table of contentsHIMax10.2.9 Accept
Page 8: 1 Safety Manual HIMax1.5 GlossaryTe
Page 12 and 13: 2 Intended Use HIMaxStandardEC/EN 6
Page 14 and 15: 2 Intended Use HIMax2.3.4 Power Sup
Page 16 and 17: 3 Safety Concept for Using the PES
Page 24 and 25: 4 Processor Modules HIMaxNOTESystem
Page 28 and 29: 6 Communication Module HIMax6 Commu
Page 30 and 31: 7 Input Modules HIMaxNOTICESystem m
Page 32 and 33: 7 Input Modules HIMax7.6 Checklists
Page 34 and 35: 7 Input Modules HIMax7.6.3 Checklis
Page 36 and 37: 7 Input Modules HIMax7.7 Safety-Rel
Page 38 and 39: 7 Input Modules HIMax7.8 Checklist
Page 40 and 41: 8 Output Modules HIMax8 Output Modu
Page 42 and 43: 8 Output Modules HIMaxIn this state
Page 44 and 45: 8 Output Modules HIMax8.7 Checklist
Page 46 and 47: 9 Software HIMax9 SoftwareThe softw
Page 48 and 49: 9 Software HIMax9.4 Resource Parame
Page 50 and 51: 9 Software HIMaxExample: A key swit
Page 52 and 53: 9 Software HIMaxThe user only need
Page 54 and 55: 10 User program HIMaxSensors (digit
Page 56 and 57: 10 User program HIMax10.2.5 Downloa
Page 58 and 59: 10 User program HIMax10.2.10 Checkl
Page 60 and 61: 11 Configuring Communication HIMaxN
Page 62 and 63: 11 Configuring Communication HIMaxF
Page 64 and 65: 11 Configuring Communication HIMaxP
Page 66 and 67: AppendixHIMaxIndex of FiguresFigure
Page 68: AppendixHIMaxIndexanalog inputsuse

HIMax Safety Manual - Tuv-fs.com

Create successful ePaper yourself

Delete template?

Save as template?