Controller HX8258 datasheet - M-COMP

More documents

Recommendations

Info

<strong>HX8258</strong>-A1200CH TFT LCD Source Driver with TCONDATA SHEET V02Pin nameTENI/OSettingDescriptionRPI1/2 I H/L Repair OP input.RPO1/2 O H/L Repair OP output.V1~V10 I H/LUsed as reference voltage input pins.Hold the reference voltage fixed during the period of LCD driveoutput. To ensure the correct analog voltage is output from D/Aconverter, the V1~V10 must be stable before D/A conversion.VDDA>V1>V2>V3>V4>V5>V6>V7>V8>V9>V10>VSS.Work with RESL[2:0], LRRESL[2:0] ID[1:0]Sample cycleLR = H LR = LChannel Number00 1 ~ 400 401 ~ 800 1200CH (S1 ~ S1200)000/00101 401 ~ 800 1 ~ 400 1200CH (S1 ~ S1200)(800X480/10800X600)NA1100 1 ~ 342 683 ~ 10241026CH (S1 ~ S513/S688ID[1:0] I H/LSPCKSDISPENSDOCKVOEVSTVDSTVUHimax ConfidentialIIIOOOOOHLHLHLHLHLHLHLH010/011(1024X600/1024X768)~ S1200)01 343 ~ 684 341 ~ 6821026CH (S1 ~ S513/S688~ S1200)10 685 ~ 1024 1 ~ 3401020CH (S1 ~ S513/S688~ S1194)11 NA00 1 ~ 400 1 ~ 400 1200CH (S1 ~ S1200)01111(400x240) 10NA11Serial port Clock. (Default pull high).Short SPCK to GNDSerial port Data input. (Default pull high).Short SDI to GNDSerial port Data Enable Signal. (Default pull high).Short SPEN to GND3-Wire serial bus data outputFloating SDOGate driver clock.Floating CKVEnable output control of gate driver.Floating OEVStart pulse for gate driver.When UD=L, STVD is output.When UD=H, STVD is Hi-Z.Floating STVDStart pulse for gate driver.When UD=L, STVU is Hi-Z.When UD=H, STVU is output.L Floating STVUH Reverse of UD.UDB OL Floating UDBH Internal link to UD.UDP OL Floating UDPSO1~SO1200 O H/L Output driver signal.TEST[1:0] I H/L Test pins. (Default pull low).TESTG[1:0] I H/L Test pin. (Default pull low).TP[3:0] O H/L Test pins. They must be open.VDDA I H/L Analog power. 6.5V to 13.5V.This information contained herein is the exclusive property of Himax and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Himax.-P.7-January, 2007
<strong>HX8258</strong>-A1200CH TFT LCD Source Driver with TCONDATA SHEET V02TENPin name I/ODescriptionSettingVSS I H/L Analog ground.VCC I H/L Digital power. 2.7V to 3.6V.GND I H/L Digital ground.PASS1- H/L Link together internally. Please use as signal path, not power path.PASS2Note: (1) Please power on following the sequence VCC logic input VDDA and V1 ~ V10. Reverse thesequence to shut down.(2) To stabilize the supply voltages, please be sure to insert a 0.1uF bypass capacitor betweenVCC-GND and VDDA-VSS. Furthermore, for increased precision of the D/A converter, insertion ofa bypass capacitor of about 0.01uF is also advised between the gamma-corrected power supplyterminals (V1, V2, …, V10) and VSS.(3) Please keep V1~V10 not cross to the toggle signals as possible to avoid the AC coupling on theDC V1~V10 voltage. When used as cascade mode, please keep the coupled amount of V1~V10are the same between the two chips.(4) The input wiring resistance values affect power or signal integrity and the display quality. So besure to design using values that do not exceed those recommended as below.Pin NameWiring resistance value(Ω)VCC(3.3V) < 30GND(0V) < 30VDDA(8.4V) < 5VSS(0V) < 5V1 ~ V10 < 100CLK < 100Dx7 ~ Dx0 < 200HS < 200VS < 200DEN < 200POL1 to POL2 < 200STV1 to STV2 < 200DIO1 to DIO2 < 200Others < 1000Himax ConfidentialThis information contained herein is the exclusive property of Himax and shall not be distributed, reproduced, or disclosedin whole or in part without prior written permission of Himax.-P.8-January, 2007
Page 1 and 2: ( DOC No. HX8258-A-DS )HX8258-A1200
Page 3 and 4: HX8258-A1200CH TFT LCD Source Drive
Page 7: HX8258-A1200CH TFT LCD Source Drive
Page 47: HX8258-A1200CH TFT LCD Source Drive
Page 59 and 60:
HX8258-A1200CH TFT LCD Source Drive
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73:
show all

Controller HX8258 datasheet - M-COMP

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?