Standard Technical Features of BTG System for Supercritical 660 ...

More documents

Recommendations

Info

Standard Technical Features of BTG System for Supercritical 660/800 MW Thermal Unitsextraction from CRH line, the maximum expected HPT exhaust pressureshall also be taken into account.14.5 Flash Tanks14.5.1 The flash tanks shall be provided receive the drains and safety valveconnections from various equipments and systems. These, as a minimum,shall include Unit flash tank, turbine drain flash tanks (left & right), HP drainflash tank and LP drain flash tank.14.5.2 The drains shall be connected to the flash tanks via headers which shall begraded according to the pressure, the farthest from the tank being the drainconnection with highest pressure. The arrangement for connection of variousdrains to the flash tanks shall be as under:i) The drains from MS piping and HP bypass piping including warm upline shall be connected to unit flash tank.ii)iii)The turbine integral and power cycle drains shall be connected toturbine flash tanks with left side drains connected to left side flash tankand right side drains to the right side flash tank.The drains from CRH, HRH, LP bypass piping including warm-up line,extractions to HP heaters, CRH and auxiliary steam to BFP turbine anddeaerator (high pressure side) and drain, vent and safety valveconnections on HP heaters shall be led to the HP flash tank. The drainsof extractions to LP heaters, IP extractions to BFP turbine, BFP turbineintegral system, CRH to BFP turbine and deaerator (low pressure side),auxiliary steam header, drain, vent and safety valve connections of LPheaters and drain coolers, deaerator overflow and CEP discharge ventshall be led to the LP flash tank.The alternative scheme/ arrangement for connection of drains to differentflash tanks as per standard proven practice of OEM shall be acceptable.14.5.3 Flash tanks shall be designed as per the requirement of ASME boiler andpressure vessels (B&PV) codes, and ANSI standard. The design pressure andtemperature for the pressure vessels (except bellows) to be designed shall be3.5 kg/cm2 and 215 0 C respectively. Flash tanks shall also be designed forfull vacuum condition.14.5.4 Corrosion allowance of 3 mm shall be added to the design thickness of theshell and head of the vessels. The minimum thickness of the vesselsincluding corrosion allowance shall not be less than 8 mm.14.5.5 The Shell, head, wear plate/ baffles shall be made of ASTM 285 Gr. C orequivalent material. The material of nozzle neck shall be ASTM A 106 Gr. Bor equivalent.111
Standard Technical Features of BTG System for Supercritical 660/800 MW Thermal Units14.5.6 The temperature in the flash tanks shall be maintained by using condensatespray or service water spray (for flash tanks open to atmosphere). The sprayshall be automatically controlled. However, for flash tanks open toatmosphere continuous spray through an orifice shall also be acceptable.14.5.7 Facility shall be provided for remote manual operation of the drain valvesfrom the control room. Motor operated drain valves shall be interlocked toopen/ close as per the process requirements. Position indication of drainvalves shall be provided in the control room.112
Page 1 and 2:
STANDARD TECHNICAL FEATURESOFBTG SY
Page 5 and 6:
Standard Technical Features of BTG
Page 7 and 8:
Page 9 and 10:
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74: Standard Technical Features of BTG
Page 123: Standard Technical Features of BTG
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
show all

Standard Technical Features of BTG System for Supercritical 660 ...

Create successful ePaper yourself

Delete template?

Save as template?