Standard Technical Features of BTG System for Supercritical 660 ...
Standard Technical Features of BTG System for Supercritical 660 ... Standard Technical Features of BTG System for Supercritical 660 ...
Standard Technical Features of BTG System for Supercritical 660/800 MW Thermal Units12.1 General12.1.1 TypeCHAPTER - 12STEAM TURBINEThe steam turbine shall be tandem compound, single reheat, regenerative,condensing, multi-cylinder design with separate HP, separate IP and separateLP casing(s) OR combined HP-IP and separate LP casing(s), directly coupledwith generator suitable for indoor installation. HP turbine shall be of doublecasing design. HP inner cylinder, IP cylinder and LP cylinder(s) shall behorizontally split.12.1.2 RatingThe steam turbine generator unit shall conform to the following design andduty conditions:i) Output under turbine maximumcontinuous rating (TMCR) at generatorterminals: 660 or 800 MW,as applicable.ii) Turbine throttle steam pressure (minimum) : 247 kg/cm 2 (abs).iii) Turbine throttle main steam temp. (minimum) : 565 0 C.iv) Reheat steam temp. at turbine inlet(minimum)v) Maximum turbine cycle heat rate at 100%TMCR, 33 0 C, 0% make up with TD-BFPs: 593 0 C.: 1850 kcal/kWh.vi) HPT exhaust pressure : To be selected bythe turbinemanufacturer asper optimisationof turbine cycle.vii) Design & operational requirement including : As per IEC 45variations in rated steam temperature & except as forpressurespecificallyindicated in thedocument.viii) Pressure drop in reheat circuit i.e. between HP : Maximum 10% ofturbine exhaust & IP turbine inletHPT exhaustpressure.87
Standard Technical Features of BTG System for Supercritical 660/800 MW Thermal Unitsix) Cooling water temperature at inlet to : 33 0 C 1condenserx) Maximum design condenser pressure : 77 mm Hg (abs) 2xi) Turbine speed : 3000 rpm.xii)Frequency variation range around ratedfrequency of 50 Hzxiii) DM water make up to thermal cycle underTMCR conditionxiv) Final feed water temp. for Heat Rateguarantee point & TMCR condition: (-) 5% to (+) 3%(47.5 Hz to 51.5Hz).: 1% of throttlesteam flow.: To be selected bythe turbinemanufacturer asper optimisationof turbine cycle.xv) Turbine protection against water induction : As per ASME-TDP-I, Latestedition.The Turbine maximum continuous rating (TMCR) output shall be achieved atgenerator terminals after deducting all electrical power used for excitation,turbine generator control, lubrication, generator cooling and sealing, turbinegland steam exhauster, turbine generator main oil tank vapour extractor andany other such integral auxiliary of turbine generator under rated steamconditions with heat cycle makeup of 1% of throttle steam flow, all extractionsin operation and design condenser pressure.Note:a) "Throttle/main steam conditions" means initial/main steam conditions(i.e. pressure, temperature and flow) at inlet to main steam strainer.b) "Reheat steam conditions" means reheat steam conditions (i.e. pressure,temperature and flow) at inlet to reheat steam strainer.12.1.3 Other featuresi) Turbine shall be capable of operating continuously with valves wideopen (V.W.O.) to swallow at least 105% of TMCR steam flow to theturbine at rated main steam and reheat steam parameters and also thecorresponding output shall not be less than 105% of rated load with 0%make up and design condenser pressure.Overload valve (HP stage bypass) to meet the above specified VWOrequirement is also acceptable, if it is a proven practice of the Turbine1 30 0 C for sea water based once through type CW system2 60 mm Hg (abs) for sea water based once through type CW system88
- Page 49 and 50: Standard Technical Features of BTG
- Page 51 and 52: Standard Technical Features of BTG
- Page 53 and 54: Standard Technical Features of BTG
- Page 55 and 56: Standard Technical Features of BTG
- Page 57 and 58: Standard Technical Features of BTG
- Page 59 and 60: Standard Technical Features of BTG
- Page 61 and 62: Standard Technical Features of BTG
- Page 63 and 64: Standard Technical Features of BTG
- Page 65 and 66: Standard Technical Features of BTG
- Page 67 and 68: Standard Technical Features of BTG
- Page 69 and 70: Standard Technical Features of BTG
- Page 71 and 72: Standard Technical Features of BTG
- Page 73 and 74: Standard Technical Features of BTG
- Page 75 and 76: Standard Technical Features of BTG
- Page 77 and 78: Standard Technical Features of BTG
- Page 79 and 80: Standard Technical Features of BTG
- Page 81 and 82: Standard Technical Features of BTG
- Page 83 and 84: Standard Technical Features of BTG
- Page 85 and 86: Standard Technical Features of BTG
- Page 87 and 88: Standard Technical Features of BTG
- Page 89 and 90: Standard Technical Features of BTG
- Page 91 and 92: Standard Technical Features of BTG
- Page 93 and 94: Standard Technical Features of BTG
- Page 95 and 96: Standard Technical Features of BTG
- Page 97 and 98: Standard Technical Features of BTG
- Page 99: Standard Technical Features of BTG
- Page 103 and 104: Standard Technical Features of BTG
- Page 105 and 106: Standard Technical Features of BTG
- Page 107 and 108: Standard Technical Features of BTG
- Page 109 and 110: Standard Technical Features of BTG
- Page 111 and 112: Standard Technical Features of BTG
- Page 113 and 114: Standard Technical Features of BTG
- Page 115 and 116: Standard Technical Features of BTG
- Page 117 and 118: Standard Technical Features of BTG
- Page 119 and 120: Standard Technical Features of BTG
- Page 121 and 122: Standard Technical Features of BTG
- Page 123 and 124: Standard Technical Features of BTG
- Page 125 and 126: Standard Technical Features of BTG
- Page 127 and 128: Standard Technical Features of BTG
- Page 129 and 130: Standard Technical Features of BTG
- Page 131 and 132: Standard Technical Features of BTG
- Page 133 and 134: Standard Technical Features of BTG
- Page 135 and 136: Standard Technical Features of BTG
- Page 137 and 138: Standard Technical Features of BTG
- Page 139 and 140: Standard Technical Features of BTG
- Page 141 and 142: Standard Technical Features of BTG
- Page 143 and 144: Standard Technical Features of BTG
- Page 145 and 146: Standard Technical Features of BTG
- Page 148 and 149: Standard Technical Features of BTG
<strong>Standard</strong> <strong>Technical</strong> <strong>Features</strong> <strong>of</strong> <strong>BTG</strong> <strong>System</strong> <strong>for</strong> <strong>Supercritical</strong> <strong>660</strong>/800 MW Thermal Unitsix) Cooling water temperature at inlet to : 33 0 C 1condenserx) Maximum design condenser pressure : 77 mm Hg (abs) 2xi) Turbine speed : 3000 rpm.xii)Frequency variation range around ratedfrequency <strong>of</strong> 50 Hzxiii) DM water make up to thermal cycle underTMCR conditionxiv) Final feed water temp. <strong>for</strong> Heat Rateguarantee point & TMCR condition: (-) 5% to (+) 3%(47.5 Hz to 51.5Hz).: 1% <strong>of</strong> throttlesteam flow.: To be selected bythe turbinemanufacturer asper optimisation<strong>of</strong> turbine cycle.xv) Turbine protection against water induction : As per ASME-TDP-I, Latestedition.The Turbine maximum continuous rating (TMCR) output shall be achieved atgenerator terminals after deducting all electrical power used <strong>for</strong> excitation,turbine generator control, lubrication, generator cooling and sealing, turbinegland steam exhauster, turbine generator main oil tank vapour extractor andany other such integral auxiliary <strong>of</strong> turbine generator under rated steamconditions with heat cycle makeup <strong>of</strong> 1% <strong>of</strong> throttle steam flow, all extractionsin operation and design condenser pressure.Note:a) "Throttle/main steam conditions" means initial/main steam conditions(i.e. pressure, temperature and flow) at inlet to main steam strainer.b) "Reheat steam conditions" means reheat steam conditions (i.e. pressure,temperature and flow) at inlet to reheat steam strainer.12.1.3 Other featuresi) Turbine shall be capable <strong>of</strong> operating continuously with valves wideopen (V.W.O.) to swallow at least 105% <strong>of</strong> TMCR steam flow to theturbine at rated main steam and reheat steam parameters and also thecorresponding output shall not be less than 105% <strong>of</strong> rated load with 0%make up and design condenser pressure.Overload valve (HP stage bypass) to meet the above specified VWOrequirement is also acceptable, if it is a proven practice <strong>of</strong> the Turbine1 30 0 C <strong>for</strong> sea water based once through type CW system2 60 mm Hg (abs) <strong>for</strong> sea water based once through type CW system88