XR1045 Operation Manual - Xtreme Manufacturing

More documents

Recommendations

Info

OperationXR1045Operator MaintenanceFigure 7-1. Check Hydraulic Oil Sight Gauge.Figure 7-4. Check Engine Oil Level. Add Engine Oil, If Necessary.Figure 7-2. Add Hydraulic Oil, If Necessary.Figure 7-5. Check Battery Case and Terminals.Figure 7-3. Check Coolant Reservoir Level. Add Coolant, IfNecessary.Figure 7-6. Store Operation and Safety Manual In Protective Case.Page 50Xtreme Manufacturing, LLC
XR1045OperationBefore Starting Forklift Warninginjury.Failure to use proper safety procedureswhen mounting and dismounting theforklift could result in death or serious• Keep steps clear of dirt, mud, snow, ice, debris, andother hazards.• Face the forklift for mounting or dismounting. Usehand holds and steps to maintain three (3) points ofcontact at all times, either both hands and one footor both feet and one hand.• DO NOT use the controls, steering wheel, or footpedals as hand holds or steps. Avoid accidentallyengaging or disengaging a control.DO NOT jump from the forklift.Clothing can get caught on pedals, levers,or other protruding parts. Landing onuneven surfaces could result in death orserious injury.1. Master battery disconnect on.2. Use safe mounting/dismounting procedures to enterthe operator cab.3. Adjust the operator seat for position and comfort.(Refer to Seat Adjustment section in this manual)4. Adjust mirrors (this may require assistance).5. Adjust the side console control panel.6. Fasten seat belt.7. Make sure the travel select lever is set to NEUTRAL (N)and the Parking Brake is ON (engaged).Figure 7-8. Parking Brake Switch (A) Must Be ON (Engaged) To StartThe Reach Forklift.Starting ForkliftNormal Starting WarningTo prevent death, serious injury, orproperty damage, the operator must beseated with seat belt fastened, arms, legs,and head completely inside the RolloverProtection Structure/Falling Object ProtectionStructure (ROPS/FOPS), the travel select lever inNEUTRAL, and the Parking Brake switch ON (engaged)BEFORE starting the forklift.1. Place key in Ignition switch. (Continue with step 3)NOTE: The engine will only start when the travel selectlever is in NEUTRAL (N) and the Parking Brake switch is ON(engaged).Figure 7-9. Key and Ignition Switch.CautionRelease the key immediately once the motor starts.If the motor does not start, DO NOT crank the startermotor continuously for more than 15 seconds. Failureto release the key after the motor has started orcontinuous cranking may damage the starter motor.Figure 7-7. Travel Select Lever Must Be In NEUTRAL (N) To Start TheReach Forklift.For information call (800) 497-1704 Page 51
Page 5 and 6: XR1045IntroductionIntroductionGener
Page 8: SafetyXR1045DO NOTJump WhileDismoun
Page 11 and 12: XR1045Safety WarningWear appropriat
Page 13 and 14: XR1045Safety WarningNEVER allow pas
Page 15 and 16: XR1045SafetyLoad SafetyAttachments
Page 17 and 18: XR1045Safety WarningLead-acid batte
Page 19 and 20: XR1045SafetyRe-activating Parking B
Page 21 and 22: XR1045LabelsFront ViewRear ViewFigu
Page 23 and 24: Front & RearWheels MustBe CenteredB
Page 25 and 26: XR1045Labels13) 18020-001 14) 18021
Page 31 and 32: XR1045LabelsCARRIAGE DAMAGEDAMAGE m
Page 33 and 34: XR1045LabelsLOAD RATINGSSHOWN ARE F
Page 35 and 36: XR1045SpecificationsXR1045 Specific
Page 37 and 38: XR1045Operator CabService Brake Ped
Page 39 and 40: XR1045Operator Cab WarningDO NOT ad
Page 41 and 42: XR1045Operator CabLow Brake Pressur
Page 43 and 44: XR1045Operator CabRear Axle Centeri
Page 45 and 46: XR1045Operator CabATable 7. Boom Co
Page 47 and 48: XR1045Operator CabOptional Controls
Page 49 and 50: XR1045Operation Warning WarningLead
Page 51: XR1045OperationFunctional Tests War
Page 55 and 56: XR1045Operation WarningWear eye pro
Page 57 and 58: XR1045Shifting Gears WarningDO NOT
Page 59 and 60: XR1045OperationRefuelingAttachments
Page 61 and 62: XR1045Operation WarningHydraulic at
Page 63 and 64: XR10457. With lock lever raised, in
Page 65 and 66: XR1045Operation9. Lower the attachm
Page 67 and 68: XR10454. Use the frame sway control
Page 69 and 70: XR1045The frame sway control handle
Page 71 and 72: XR1045OperationStandard Carriage Lo
Page 73 and 74: XR1045After Every 500 Hours of Oper
Page 75 and 76: XR1045Preventive MaintenanceTHIS PA
Page 77 and 78: XR1045Lockout / TagoutDo Not Operat
Page 79 and 80: XR1045Lockout / TagoutFor informati

XR1045 Operation Manual - Xtreme Manufacturing

Create successful ePaper yourself

Delete template?

Save as template?