AIR CONDITIONER - Heronhill Air Conditioning Ltd
AIR CONDITIONER - Heronhill Air Conditioning Ltd AIR CONDITIONER - Heronhill Air Conditioning Ltd
10. PART REPLACEMENTFILE NO. SVM-0502010-1. Indoor UnitNo. Part name Procedures Remarks1 Front panelHow to remove the front panel1) Stop the operation of the air conditioner andturn off its main power supply.2) Pull the air inlet grille toward you to open itand remove the air inlet grille.Then remove the 4 screws fixing the frontpanel.3) First open the horizontal louver, and thenremove the front panel from the back bodyby pulling it toward you.222 4-Screws32How to mount the front panelPush the front panel back in and make sureall hooks are locked.2 Electrical partHow to remove the electrical part.1) Remove the front panel with procedure 1 .2) Remove the screw holding the electrical partcover.3) Disconnect the 2 connectors (3P) for the fanmotor and the connector (5P) for the louvermotor from the P.C. board assembly.4) Pull out the TC sensor from the sensorholder.5) Remove the screw for the ground connection,remove the 2 screws for the electrical partbox and remove the screw from the LED unit.Then remove the LED unit and the electricalpart box from the main unit.2 Screws4 TC SensorHow to mount the electrical part.1) To put back the electrical part box, lock it tothe upper hook of the back body.2) Tighten the screws on the electrical part box.3) Connect the 3 connectors and arrange thewiring same as original condition and thentighten the screw from the LED unit to theback body.4) Attach the TC sensor to the holder.5) Tighten the screw for the ground connection.6) Assemble the drain guide (the TC sensor wireshould be covered by the drain guide).7) Tighten the screw on the electrical part cover.5 Screw33-Connectors6 Screw3 Horizontallouver1) Remove the front panel and the electricalpart following procedure 2.2) Remove the center shaft of the horizontallouver from the back body.3) Remove the left shaft from the back body.4) Remove the horizontal louver from the backbody.3 Left shaft2 Center shaft− 71 −
FILE NO. SVM-05020No. Part name Procedures Remarks4 Heat exchanger1) Remove the front panel, electrical part andthe horizontal louver following procedure 3.2) Remove the pipe holder at the rear side ofmain unit.3) Remove the 2 screws on the heat exchangerat the base bearing.4) Remove the 2 screws on the heat exchangerat the 2 fixed plates (upper and lower) fromthe back body, and then pull out the upperside of the heat exchanger slowly.2 Pipe holder32-Screws42-Screws5 Cross flow fan1) Remove the front panel, electrical part,horizontal louver and the heat exchangerfollowing procedure 4.2) Remove the 2 screws on the band motor (L)and remove the 2 screws on the band motor(R) and then remove the cross flow fan.3) Loosen the set screw of the cross flow fanthen separate the fan and the fan motor.NoticeTo assemble cross flow fan and fan motor to theunit, please turn the fan motor unit the center ofits terminal meets the lowest point of band motor(R) (point A).Fix the cross flow fan with the set screw at theposition where the gap between the back bodyand the right surface of the cross flow fan is6 mm.2 2-Screws (L)6 mm6 Set screwMiddle of the fan motor terminal22-Screws(R)6 Base bearing1) Remove the front panel, electrical part,horizontal louver, heat exchanger and thecross flow fan following procedure 5.2) Remove the 2 screws fixing the base bearing.3) Remove the bearing from the base bearing. Ifthe housing protrudes from the base bearing,put the housing in position and attach thebearing to the base bearing.22-Screws− 72 −
- Page 21 and 22: 5-2. RAS-10UKHP-ES4 / RAS-10UAH-ES4
- Page 23 and 24: FILE NO. SVM-050205-4. RAS-10UKP-ES
- Page 25 and 26: 6. CONTROL BLOCK DIAGRAMFILE NO. SV
- Page 27 and 28: 7. OPERATION DESCRIPTIONFILE NO. SV
- Page 29 and 30: 7-2-3. Dry operation([MODE] button
- Page 31 and 32: 7-3. Hi POWER Mode([Hi POWER] butto
- Page 33 and 34: 7-7. Current Limit Control *Heat pu
- Page 35 and 36: 7-8-2. How to cancel auto restart f
- Page 37 and 38: FILE NO. SVM-050207-11. QUIET ModeQ
- Page 39 and 40: DANGER− 38 −FILE NO. SVM-05020
- Page 41 and 42: 8-3. Installation8-3-1. Optional in
- Page 43 and 44: 8-3-3. Installation/Servicing tools
- Page 45 and 46: FILE NO. SVM-050201. Securely fit t
- Page 47 and 48: FILE NO. SVM-050208-4-4. Piping and
- Page 49 and 50: FILE NO. SVM-050208-4-6. Drainage1.
- Page 51 and 52: 8-5-3. EvacuatingAfter the piping h
- Page 53 and 54: FILE NO. SVM-050202. Set the remote
- Page 55 and 56: 9-3. Primary Judgement9-3-1. Role o
- Page 57 and 58: Table 9-4-1FILE NO. SVM-05020Checkc
- Page 59 and 60: FILE NO. SVM-05020Cooling ModelOper
- Page 61 and 62: FILE NO. SVM-05020RAS-13UKP-ES4, RA
- Page 63 and 64: 9-5-5. Only outdoor fan does not op
- Page 65 and 66: FILE NO. SVM-050209-5-7. Only the i
- Page 67 and 68: 9-6. Troubleshooting for Remote Con
- Page 69 and 70: (3) Checking procedureHeat Pump Mod
- Page 71: Table 9-6-3 Approximate resistance
- Page 75 and 76: FILE NO. SVM-05020No. Part name Pro
- Page 77 and 78: FILE NO. SVM-0502011. EXPLODED VIEW
- Page 79 and 80: FILE NO. SVM-0502011-4. Outdoor Uni
- Page 81 and 82: 11-6. Outdoor Unit (RAS-13UA-ES4)FI
- Page 83 and 84: FILE NO. SVM-0502011-8. Outdoor Uni
10. PART REPLACEMENTFILE NO. SVM-0502010-1. Indoor UnitNo. Part name Procedures Remarks1 Front panelHow to remove the front panel1) Stop the operation of the air conditioner andturn off its main power supply.2) Pull the air inlet grille toward you to open itand remove the air inlet grille.Then remove the 4 screws fixing the frontpanel.3) First open the horizontal louver, and thenremove the front panel from the back bodyby pulling it toward you.222 4-Screws32How to mount the front panelPush the front panel back in and make sureall hooks are locked.2 Electrical partHow to remove the electrical part.1) Remove the front panel with procedure 1 .2) Remove the screw holding the electrical partcover.3) Disconnect the 2 connectors (3P) for the fanmotor and the connector (5P) for the louvermotor from the P.C. board assembly.4) Pull out the TC sensor from the sensorholder.5) Remove the screw for the ground connection,remove the 2 screws for the electrical partbox and remove the screw from the LED unit.Then remove the LED unit and the electricalpart box from the main unit.2 Screws4 TC SensorHow to mount the electrical part.1) To put back the electrical part box, lock it tothe upper hook of the back body.2) Tighten the screws on the electrical part box.3) Connect the 3 connectors and arrange thewiring same as original condition and thentighten the screw from the LED unit to theback body.4) Attach the TC sensor to the holder.5) Tighten the screw for the ground connection.6) Assemble the drain guide (the TC sensor wireshould be covered by the drain guide).7) Tighten the screw on the electrical part cover.5 Screw33-Connectors6 Screw3 Horizontallouver1) Remove the front panel and the electricalpart following procedure 2.2) Remove the center shaft of the horizontallouver from the back body.3) Remove the left shaft from the back body.4) Remove the horizontal louver from the backbody.3 Left shaft2 Center shaft− 71 −
Change language