Owner's Manual 2010 TE/TC/TXC 310/450/510 - Husqvarna

More documents

Recommendations

Info

HEADLAMP BULBS REPLACEMENT(TE-SMR)To gain access to the healamp bulbs, proceede as follows:- remove the upper fastening screw of the the headlamp carrierto the instrument panuel support (A);- push forward the headlamp carrier (B) and pull it towards thehigh (C) in order to uncouple from the two lower supports.- remove the headlamp carrier;- remove the two filaments bulb (7) connector (2) and theboot (3);- remove the screw (6);- release the bulb holding spring (4) and then the bulb itself.To replace the parking light bulb (5) extract it from the insidecover.After replacement, reverse operations for reassembly.TAIL LIGHT (excluded TE 310/Europe)The back light is a LED light.C543AB675 42380
REAR TAIL LIGHT BULB REPLACEMENT(TE- SMR)Remove the two fastening screws (1) in the inner side of therear fender and the lens (2).Pull the lamp (3) inside, turn it counterclockwise then removeit from the lamp holder.After replacement, reverse operations for reassembly.NOTES: make sure not to tighten the screwsexcessively.REPLACING THE NUMBER PLATE LAMP(TE- SMR)Pull out the number plate lampholder (4) from the back of thevehicle. Pull out the lampholder and the bulb. Rotate the bulb(5) to remove from the lampholder.Once the bulb has been replaced, reverse the above procedure.EN4581
Page 1 and 2:
ENGLISH1
Page 3 and 4:
IMPORTANTThe reference for recognit
Page 5 and 6:
VEHICLE IDENTIFICATION NUMBER (V.I.
Page 7 and 8:
Control location1. Front brake leve
Page 9 and 10:
FINAL RATIOS1st gear (TE 310) . . .
Page 11 and 12:
CONTROLSFUEL COCK (TC-TXC)The left-
Page 13 and 14:
CARBURETOR CHOKE (TC-TXC)The starte
Page 15 and 16:
2- SPEED / CLOCK (figure 2)- SPEED:
Page 17 and 18:
THROTTLE CONTROLThe throttle knob (
Page 19 and 20:
REAR BRAKE CONTROLThe rear brake co
Page 21 and 22:
ENGINE START (TE-SMR)With cold engi
Page 23 and 24:
ENGINE START (TC-TXC)Proceed as fol
Page 25 and 26:
8) COMPLETELY lower the pedal (4) u
Page 27 and 28:
STOPPING THE MOTORCYCLE AND THE ENG
Page 29 and 30: COOLANT LEVEL CHECKCheck level (1)
Page 31 and 32: THROTTLE CABLE ADJUSTMENTTo check t
Page 33 and 34: SPARK PLUG CHECKUse NGK CR8EB spark
Page 35 and 36: AIR FILTER CHECK (TE-SMR)Turn rear
Page 37 and 38: ADJUSTMENT OF THE CONTROL LEVER AND
Page 39 and 40: CHECKING THE FLUID LEVELThe level (
Page 41 and 42: ADJUSTING THE SUSPENSIONS ACCORDING
Page 43 and 44: OIL FORK LEVELFor the regular fork
Page 45 and 46: OIL FORK LEVELFor the regular fork
Page 47 and 48: ADJUSTING THE SHOCK ABSORBERThe rea
Page 49 and 50: CHAIN ADJUSTMENT (Fig. A)Chain shou
Page 51 and 52: 2 - Check that the chain is neither
Page 53 and 54: REASSEMBLING THE FRONT WHEELFit the
Page 55 and 56: TIRESCare should be taken to keep t
Page 57 and 58: PADS CLEANINGBe careful that no dis
Page 59 and 60: DISC CLEANINGPoor braking can also
Page 61 and 62: - Pump with brake lever (3) or brak
Page 63 and 64: - Remove fluid reservoir cap (2), t
Page 65 and 66: - Restore the brake fluid level (A)
Page 67 and 68: EXHAUST MUFFLER (TC-TE-TXC)The muff
Page 69 and 70: OVERHAULING THE WHEELSDEFORMATION R
Page 71 and 72: - Two fuses (9) 15A and one (13) 20
Page 73 and 74: - Spark plug (5) on the R.H. side o
Page 75 and 76: TE-SMR713SMR TE30 28 28 10 31 26 29
Page 77: 43219TC-TXCEN561413121073*: KIT AVV
Page 82 and 83: ADJUSTMENT OF HEADLIGHT (TE- SMR)Wh
Page 84 and 85: 84EQUIPMENTPos. Code Nr. NAME MODEL
Page 86 and 87: OPTIONAL PARTS LIST (TE)Pos. Code N
Page 88 and 89: APPENDIXAFTER-RACE CHECK POINTSAfte
Page 90 and 91: it is necessary ABSOLUTELY TO AVOID
Page 92 and 93: NOTES FOR USA/CDN MODELDISCLAIMER O
Page 94 and 95: SPARK ARRESTERThe TE (USA), TXC TC
Page 96 and 97: ALPHABETIC INDEXPageAAdjusting the
Page 98 and 99: TE-TC-TXC 310, 450, 510 - 2010MOTOC
Page 104 and 105: SMR 450, 510- 2010 - TE 310, 450, 5
Page 106 and 107: SMR 450, 510- 2010 - TE 310, 450, 5
Page 108 and 109: SMR 450, 510- 2010 - TE 310, 450, 5
show all

Owner's Manual 2010 TE/TC/TXC 310/450/510 - Husqvarna

Create successful ePaper yourself

Delete template?

Save as template?