Owner's Manual 2010 TE/TC/TXC 310/450/510 - Husqvarna
Owner's Manual 2010 TE/TC/TXC 310/450/510 - Husqvarna Owner's Manual 2010 TE/TC/TXC 310/450/510 - Husqvarna
REMOVING THE REAR WHEELUnscrew the nut (1) of the wheel pin (3) and extract it. It is notnecessary to unloose the chain adjusters (2); in this way, thechain tension will remain unchanged after the reassembly.Extract the complete rear wheel, by taking care of the spacerslocated at the hub sides.To reassemble, reverse the above procedure remembering toinsert the disc into the caliper.NOTESDo not operate the rear brake pedal when the wheel has beenremoved; this causes the caliper piston to move outwards.After removal, lay down the wheel with brake disc on top.After reassembly, pump the brake control pedal until the padsare against the brake disc.1254
TIRESCare should be taken to keep the tires properly inflated. Seetire data for correct tire inflation pressure (page 11). Replacethe tire if its wear exceeds what is shown on the table below.FRONTMINIMUM HEIGHT OFTHE TREAD3 mm (TC,TE,TXC); 2 mm (SMR)BRAKESThe mayor components are brake master cylinder with its lever(front) or pedal (rear), brakeline, caliper assembly and disc.LEGEND1. Front brake control lever2. Front brake pump with oil reservoir (TE, TC,TXC)2. Front brake pump (SMR)2A. Oil reservoir (SMR)3. Front brake hose4. Front brake caliper5. Front brake disc6. Rear brake oil tank7. Rear brake hose8. Rear brake caliper9. Rear brake disc10. Rear brake pump11. Rear brake control pedalENREAR3 mm (TC,TE,TXC); 2 mm (SMR)6112A1055
- Page 3 and 4: IMPORTANTThe reference for recognit
- Page 5 and 6: VEHICLE IDENTIFICATION NUMBER (V.I.
- Page 7 and 8: Control location1. Front brake leve
- Page 9 and 10: FINAL RATIOS1st gear (TE 310) . . .
- Page 11 and 12: CONTROLSFUEL COCK (TC-TXC)The left-
- Page 13 and 14: CARBURETOR CHOKE (TC-TXC)The starte
- Page 15 and 16: 2- SPEED / CLOCK (figure 2)- SPEED:
- Page 17 and 18: THROTTLE CONTROLThe throttle knob (
- Page 19 and 20: REAR BRAKE CONTROLThe rear brake co
- Page 21 and 22: ENGINE START (TE-SMR)With cold engi
- Page 23 and 24: ENGINE START (TC-TXC)Proceed as fol
- Page 25 and 26: 8) COMPLETELY lower the pedal (4) u
- Page 27 and 28: STOPPING THE MOTORCYCLE AND THE ENG
- Page 29 and 30: COOLANT LEVEL CHECKCheck level (1)
- Page 31 and 32: THROTTLE CABLE ADJUSTMENTTo check t
- Page 33 and 34: SPARK PLUG CHECKUse NGK CR8EB spark
- Page 35 and 36: AIR FILTER CHECK (TE-SMR)Turn rear
- Page 37 and 38: ADJUSTMENT OF THE CONTROL LEVER AND
- Page 39 and 40: CHECKING THE FLUID LEVELThe level (
- Page 41 and 42: ADJUSTING THE SUSPENSIONS ACCORDING
- Page 43 and 44: OIL FORK LEVELFor the regular fork
- Page 45 and 46: OIL FORK LEVELFor the regular fork
- Page 47 and 48: ADJUSTING THE SHOCK ABSORBERThe rea
- Page 49 and 50: CHAIN ADJUSTMENT (Fig. A)Chain shou
- Page 51 and 52: 2 - Check that the chain is neither
- Page 53: REASSEMBLING THE FRONT WHEELFit the
- Page 57 and 58: PADS CLEANINGBe careful that no dis
- Page 59 and 60: DISC CLEANINGPoor braking can also
- Page 61 and 62: - Pump with brake lever (3) or brak
- Page 63 and 64: - Remove fluid reservoir cap (2), t
- Page 65 and 66: - Restore the brake fluid level (A)
- Page 67 and 68: EXHAUST MUFFLER (TC-TE-TXC)The muff
- Page 69 and 70: OVERHAULING THE WHEELSDEFORMATION R
- Page 71 and 72: - Two fuses (9) 15A and one (13) 20
- Page 73 and 74: - Spark plug (5) on the R.H. side o
- Page 75 and 76: TE-SMR713SMR TE30 28 28 10 31 26 29
- Page 77: 43219TC-TXCEN561413121073*: KIT AVV
- Page 80 and 81: HEADLAMP BULBS REPLACEMENT(TE-SMR)T
- Page 82 and 83: ADJUSTMENT OF HEADLIGHT (TE- SMR)Wh
- Page 84 and 85: 84EQUIPMENTPos. Code Nr. NAME MODEL
- Page 86 and 87: OPTIONAL PARTS LIST (TE)Pos. Code N
- Page 88 and 89: APPENDIXAFTER-RACE CHECK POINTSAfte
- Page 90 and 91: it is necessary ABSOLUTELY TO AVOID
- Page 92 and 93: NOTES FOR USA/CDN MODELDISCLAIMER O
- Page 94 and 95: SPARK ARRESTERThe TE (USA), TXC TC
- Page 96 and 97: ALPHABETIC INDEXPageAAdjusting the
- Page 98 and 99: TE-TC-TXC 310, 450, 510 - 2010MOTOC
- Page 100 and 101: TE-TC-TXC 310, 450, 510 - 2010MOTOC
- Page 102 and 103: TE-TC-TXC 310, 450, 510 - 2010MOTOC
TIRESCare should be taken to keep the tires properly inflated. Seetire data for correct tire inflation pressure (page 11). Replacethe tire if its wear exceeds what is shown on the table below.FRONTMINIMUM HEIGHT OFTHE TREAD3 mm (<strong>TC</strong>,<strong>TE</strong>,<strong>TXC</strong>); 2 mm (SMR)BRAKESThe mayor components are brake master cylinder with its lever(front) or pedal (rear), brakeline, caliper assembly and disc.LEGEND1. Front brake control lever2. Front brake pump with oil reservoir (<strong>TE</strong>, <strong>TC</strong>,<strong>TXC</strong>)2. Front brake pump (SMR)2A. Oil reservoir (SMR)3. Front brake hose4. Front brake caliper5. Front brake disc6. Rear brake oil tank7. Rear brake hose8. Rear brake caliper9. Rear brake disc10. Rear brake pump11. Rear brake control pedalENREAR3 mm (<strong>TC</strong>,<strong>TE</strong>,<strong>TXC</strong>); 2 mm (SMR)6112A1055