Platinum Spot 5R User Manual v1.2 (pdf) - Elation Professional

More documents

Recommendations

Info

Platinum Spot 5R14. ERROR CODES:When power is applied, the unit will automatically enter a “reset/test” mode. This modebrings all the internal motors to a home position. If there is an internal problem with one ormore of the motors an error code will flash in the display in the form of “XXer” were as XX willrepresent a motor function. For example, when the display shows “Pan-ER,” it means thereis some type of error with the pan motor. If there are multiple errors during the start-upprocess they will all flash in the display. For example: if the fixtures has errors on channel 1,channel 3, and channel 5 all at the same time, you will see the error message “Pan-Er”,“Tilt-Er,” and ”Color-Er” flash repeated 5 times.If an error does occur during the initial start-up procedure the fixture will self-generate asecond reset signal and try to realign all the motors and correct the error, if the error persistafter a second attempt a third attempt will be made.If after a third attempt all the errors have not been corrected the fixture will make thefollowing determinations: 1) 3 or more errors - The fixture cannot function properly with threeor more errors therefore the fixture will place itself in a stand-by mode until subsequentrepairs can be made. 2) Less than 3 errors - The fixture has less than 3 errors, thereforemost other functions will work properly. The fixture will attempt to operate normally until theerrors can be correct by a technician. The errors in question will remain flashing in thedisplay as a reminder of internal errors.Pan Movement error:The yoke is not located in the default position after start-up or after a reset command. Thismessage will appear after a fixture reset if the pan-yoke’s magnetic-indexing circuitmalfunctions (sensor failed or magnet is missing) or there is a stepper motor failure(defective motor or a defective motor IC drive on the main PCB).Tilt Movement error:The head is not located in the default tilt position after start-up or after a reset command.This message will appear after a fixture reset if the tilt magnetic-indexing circuit malfunctions(sensor failed or magnet is missing) or there is a stepper motor failure (defective motor or a©Elation Professional, Los Angeles Ca. 48 www.ElationLighting.com
Platinum Spot 5Rdefective motor IC drive on the main PCB).Color-wheel error:The color wheel is not located in the default position after start-up or after a reset command.This message will appear after a fixture reset if the color wheel’s magnetic-indexing circuitmalfunctions (sensor failed or magnet is missing) or there is a stepper motor failure(defective motor or a defective motor IC drive on the main PCB).Rotating gobo-wheel error:The gobo-wheel is not located in the default position after start-up or after a reset command.This message will appear after a fixture reset if the gobo wheel’s magnetic-indexing circuitmalfunctions (sensor failed or magnet is missing) or there is a stepper motor failure(defective motor or a defective motor IC drive on the main PCB).Rotating gobo indexing error:The gobo is not located in the default position after start-up or after a reset command. Thismessage will appear after a fixture reset if the gobo positioning magnetic-indexing circuitmalfunctions (sensor failed or magnet is missing) or there is a stepper motor failure(defective motor or a defective motor IC drive on the main PCB).Fix Gobo-wheel error:This message will appear after the reset of the fixture if the magnetic-indexing circuitmalfunctions (sensor failed or magnet missing) or the stepping-motor is defective (or its drivecircuit on the main PCB). The fix gobo wheel is not located in the default position after thereset.Prism Rotation error:This message will appear after the reset of the fixture and if the magnetic-indexing circuitmalfunctions (sensor failed or magnet missing) or the stepping-motor is defective (or itsdriver circuit on the main PCB). The Prism wheel is not located in the default position afterthe reset.Iris error:This message will appear after the reset of the fixture and if the magnetic-indexing circuit©Elation Professional, Los Angeles Ca. 49 www.ElationLighting.com
Page 1: Platinum Spot 5RElation Professiona
Page 5 and 6: Platinum Spot 5RPlease do not disca
Page 7 and 8: Platinum Spot 5R2. SAFETY INSTRUCTI
Page 9 and 10: Platinum Spot 5R3. FEATURES• Pan
Page 11 and 12: Platinum Spot 5R5. FIXTURE OVERVIEW
Page 13 and 14: Platinum Spot 5R13. 3-PIN DMX Input
Page 15 and 16: Platinum Spot 5Rthe replacement lam
Page 17 and 18: Platinum Spot 5R7. MOUNTING AND INS
Page 19 and 20: Platinum Spot 5RClamp MountingThe P
Page 21 and 22: Platinum Spot 5RBe sure to follow t
Page 23 and 24: Platinum Spot 5Rchannel number from
Page 25 and 26: Platinum Spot 5RDefault settings sh
Page 27 and 28: Platinum Spot 5RRec. Controller XX~
Page 29 and 30: Platinum Spot 5RClear Last RunThis
Page 31 and 32: Platinum Spot 5Ris turned off or be
Page 33 and 34: Platinum Spot 5RLOCK - This functio
Page 35 and 36: Platinum Spot 5RPrograms can be cre
Page 37 and 38: Platinum Spot 5RController Settings
Page 39 and 40: Platinum Spot 5RControl” submenu.
Page 41 and 42: Platinum Spot 5R- “PAN-Fine” -
Page 43 and 44: Platinum Spot 5R13. DMX CHANNEL TRA
Page 45 and 46: Platinum Spot 5R 119 7 1232-39 Gob
Page 47: Platinum Spot 5R16 14 2317 15 24224
Page 51 and 52: Platinum Spot 5R15. CLEANING AND MA
Page 53 and 54: Platinum Spot 5R17. GOBOS:©Elation
Page 55 and 56: Platinum Spot 5R19. CIRCUIT SCHEMAT
Page 57 and 58: Platinum Spot 5Reffect.E. Elation P
Page 59 and 60: Platinum Spot 5RTilt - movementWeig

Platinum Spot 5R User Manual v1.2 (pdf) - Elation Professional

Create successful ePaper yourself

Delete template?

Save as template?