SNMP-GSH2402 - kamery airlive airlivecam
SNMP-GSH2402 - kamery airlive airlivecam SNMP-GSH2402 - kamery airlive airlivecam
3-11. MAC TableMAC Table Configuration gathers many functions, including MAC TableInformation, MAC Table Maintenance, Static Forward, Static Filter and MAC Alias,which cannot be categorized to some function type. They are described below.Function name:MAC Table InformationFunction Description:Display the static or dynamic learning MAC entry and the state for the selectedport.Parameter description:Port:Select the port you would like to inquire.Search:Set up the MAC entry you would like to inquire.The default is ??-??-??-??-??-??MAC:Display the MAC address of one entry you selected from the searchedMAC entries table.Alias:Set Alias:Search:Set up the Alias for the selected MAC entry.Save the Alias of MAC entry you set up.Find the entry that meets your setup.Previous Page:Move to the previous page.Next Page:Alias:Move to the next page.The Alias of the searched entry.MAC Address:The MAC address of the searched entry.92
Port:The port that exists in the searched MAC Entry.VID:VLAN Group that MAC Entry exists.State:Display the method that this MAC Entry is built. It may show “DynamicMAC” or “Static MAC”.Fig. 3-3893
- Page 46 and 47: 3-1-5. Management PolicyThrough the
- Page 48 and 49: IP Range:The switch supports two ki
- Page 50 and 51: Parameter description:Fig. 3-8State
- Page 52 and 53: 3-2. Port ConfigurationFour functio
- Page 54 and 55: Speed / Duplex Mode:Display the spe
- Page 56 and 57: Vendor SN (Serial Number):Show the
- Page 58 and 59: Mode:Set the speed and duplex of th
- Page 61 and 62: Rx Packet:The counting number of th
- Page 63 and 64: Rx Low Priority Packets:Number of R
- Page 65 and 66: 3-3. MirrorFunction name:Mirror Con
- Page 67 and 68: Broadcast & Multicasat for Ingress
- Page 69 and 70: Function name:Per Port PriorityFunc
- Page 71 and 72: Bit 0, Bit 1, Bit 2:According to th
- Page 73 and 74: Bit 0, Bit 1, Bit 2:According to th
- Page 75 and 76: Prioritize Streaming Audio/Video:Be
- Page 77 and 78: Function name:IP Diffserv Classific
- Page 79 and 80: Default SNMP function : EnableDefau
- Page 81 and 82: Parameter description:IGMP snooping
- Page 83 and 84: Add:A new entry of allowed group co
- Page 85 and 86: 3-9. DHCP BootThe DHCP Boot functio
- Page 87 and 88: Metro Mode:The Metro Mode is a quic
- Page 89 and 90: 3-10-2. Tag-based GroupFunction nam
- Page 91 and 92: 3-10-3. Port-based GroupFunction na
- Page 93 and 94: modify a group‘s description and
- Page 95: Role:This is an egress rule of the
- Page 99 and 100: Function Name:Static ForwardFunctio
- Page 101 and 102: Function name:MAC AliasFunction des
- Page 103 and 104: 3-12. GVRP ConfigurationGVRP is an
- Page 105 and 106: Normal:It is Normal Registration. T
- Page 107 and 108: LeaveEmpty Message Packets:Number o
- Page 109 and 110: 3-13. STP ConfigurationThe Spanning
- Page 111 and 112: 3-13-2. STP ConfigurationThe STP, S
- Page 113 and 114: 3-13-3. STP Port ConfigurationFunct
- Page 115 and 116: M Check:Migration Check. It forces
- Page 117 and 118: Per Trunking Group supports a maxim
- Page 119 and 120: Aggtr:Status:Aggtr is an abbreviati
- Page 121 and 122: Function name:LACP Detail (LACP Agg
- Page 123 and 124: 3-15. 802.1X Configuration802.1X po
- Page 125 and 126: Authentication serverFig. 3-54CBAut
- Page 127 and 128: Only MultiHost 802.1X is the type o
- Page 129 and 130: Function name:802.1X Mode SettingFu
- Page 131 and 132: Function name:Param. SettingFunctio
- Page 133 and 134: 3-16. Alarm ConfigurationAlarm Conf
- Page 135 and 136: Parameter description:Email:Mail Se
- Page 137 and 138: 3-17-1. Save/RestoreFunction name:S
- Page 139 and 140: Function name:Restore User Configur
- Page 141 and 142: 3-18. DiagnosticsThree functions, i
- Page 143 and 144: Function name:Ping TestFunction des
- Page 145 and 146: 3-20. LogThis function shows the lo
3-11. MAC TableMAC Table Configuration gathers many functions, including MAC TableInformation, MAC Table Maintenance, Static Forward, Static Filter and MAC Alias,which cannot be categorized to some function type. They are described below.Function name:MAC Table InformationFunction Description:Display the static or dynamic learning MAC entry and the state for the selectedport.Parameter description:Port:Select the port you would like to inquire.Search:Set up the MAC entry you would like to inquire.The default is ??-??-??-??-??-??MAC:Display the MAC address of one entry you selected from the searchedMAC entries table.Alias:Set Alias:Search:Set up the Alias for the selected MAC entry.Save the Alias of MAC entry you set up.Find the entry that meets your setup.Previous Page:Move to the previous page.Next Page:Alias:Move to the next page.The Alias of the searched entry.MAC Address:The MAC address of the searched entry.92
Change language