SNMP-GSH2402 - kamery airlive airlivecam
SNMP-GSH2402 - kamery airlive airlivecam SNMP-GSH2402 - kamery airlive airlivecam
Vendor SN (Serial Number):Show the serial number assigned by the manufacturer.Date Code:Show the date this SFP module was made.Temperature:Show the current temperature of SFP module.Vcc:Show the working DC voltage of SFP module.Mon1(Bias) mA:Show the Bias current of SFP module.Mon2(TX PWR):Show the transmit power of SFP module.Mon3(RX PWR):Show the receiver power of SFP module.52
3-2-2. Port ConfigurationPort Configuration is applied to change the setting of each port. In thisconfiguration function, you can set/reset the following functions. All of them aredescribed in detail below.Function name:Port ConfigurationFunction description:Fig. 3-12It is used to set each port’s operation mode. The switch supports 3 parametersfor each port. They are state, mode and flow control.Parameter description:State:Set the communication capability of the port is Enabled or Disabled.When enabled, traffic can be transmitted and received via this port.When disabled, the port is blocked and no traffic can be transferredthrough this port. Port State is configurable by the user. There are onlytwo states “Enable” and “Disable” able to choose. If you set a port’s state“Disable”, then that port is prohibited to pass any traffic, even it looksLink up.Default: Enable.53
- Page 5 and 6: About this user’s manualIn this u
- Page 7: • Key Features in the DeviceQoS:S
- Page 10 and 11: 1-4. View of 24 Gigabit L2 Managed
- Page 12 and 13: 1-5. View of the Optional ModulesIn
- Page 14 and 15: • TP Port and Cable Installation
- Page 16 and 17: 2-1-3-1. Cabling Requirements for T
- Page 18 and 19: Case1: All switch ports are in the
- Page 20 and 21: 2-1-4. Configuring the Management A
- Page 22 and 23: • Set IP Address, Subnet Mask and
- Page 24 and 25: Fig. 2-10 the Login Screen for Web2
- Page 26 and 27: Class D and E:Class D is a class wi
- Page 28 and 29: For different network applications,
- Page 30 and 31: Fig. 2-14 Peer-to-peer Network Conn
- Page 32 and 33: In the switch, it supports a simple
- Page 34 and 35: • The Information of Page Layout
- Page 36 and 37: 3-1-1. System InformationFunction n
- Page 38 and 39: 3-1-2. IP ConfigurationIP configura
- Page 40 and 41: IP address:Users can configure the
- Page 42 and 43: 3-1-3. Time ConfigurationThe switch
- Page 44 and 45: Day Light Saving End :This is used
- Page 46 and 47: 3-1-5. Management PolicyThrough the
- Page 48 and 49: IP Range:The switch supports two ki
- Page 50 and 51: Parameter description:Fig. 3-8State
- Page 52 and 53: 3-2. Port ConfigurationFour functio
- Page 54 and 55: Speed / Duplex Mode:Display the spe
- Page 58 and 59: Mode:Set the speed and duplex of th
- Page 61 and 62: Rx Packet:The counting number of th
- Page 63 and 64: Rx Low Priority Packets:Number of R
- Page 65 and 66: 3-3. MirrorFunction name:Mirror Con
- Page 67 and 68: Broadcast & Multicasat for Ingress
- Page 69 and 70: Function name:Per Port PriorityFunc
- Page 71 and 72: Bit 0, Bit 1, Bit 2:According to th
- Page 73 and 74: Bit 0, Bit 1, Bit 2:According to th
- Page 75 and 76: Prioritize Streaming Audio/Video:Be
- Page 77 and 78: Function name:IP Diffserv Classific
- Page 79 and 80: Default SNMP function : EnableDefau
- Page 81 and 82: Parameter description:IGMP snooping
- Page 83 and 84: Add:A new entry of allowed group co
- Page 85 and 86: 3-9. DHCP BootThe DHCP Boot functio
- Page 87 and 88: Metro Mode:The Metro Mode is a quic
- Page 89 and 90: 3-10-2. Tag-based GroupFunction nam
- Page 91 and 92: 3-10-3. Port-based GroupFunction na
- Page 93 and 94: modify a group‘s description and
- Page 95 and 96: Role:This is an egress rule of the
- Page 97 and 98: Port:The port that exists in the se
- Page 99 and 100: Function Name:Static ForwardFunctio
- Page 101 and 102: Function name:MAC AliasFunction des
- Page 103 and 104: 3-12. GVRP ConfigurationGVRP is an
- Page 105 and 106: Normal:It is Normal Registration. T
3-2-2. Port ConfigurationPort Configuration is applied to change the setting of each port. In thisconfiguration function, you can set/reset the following functions. All of them aredescribed in detail below.Function name:Port ConfigurationFunction description:Fig. 3-12It is used to set each port’s operation mode. The switch supports 3 parametersfor each port. They are state, mode and flow control.Parameter description:State:Set the communication capability of the port is Enabled or Disabled.When enabled, traffic can be transmitted and received via this port.When disabled, the port is blocked and no traffic can be transferredthrough this port. Port State is configurable by the user. There are onlytwo states “Enable” and “Disable” able to choose. If you set a port’s state“Disable”, then that port is prohibited to pass any traffic, even it looksLink up.Default: Enable.53