SNMP-GSH2402 - kamery airlive airlivecam

More documents

Recommendations

Info

3-1-2. IP ConfigurationIP configuration is one of the most important configurations in the switch.Without the proper setting, network manager will not be able to manage or view thedevice. The switch supports both manual IP address setting and automatic IPaddress setting via DHCP server. When IP address is changed, you must reboot theswitch to have the setting taken effect and use the new IP to browse for webmanagement and CLI management.Function name:IP ConfigurationFunction description:Fig. 3-4 IP Address ConfigurationSet IP address, subnet mask, default gateway and DNS for the switch.Parameter description:DHCP Setting:DHCP is the abbreviation of Dynamic Host Configuration Protocol. HereDHCP means a switch to turn ON or OFF the function.The switch supports DHCP client used to get an IP address automaticallyif you set this function “Enable”. When enabled, the switch will issue therequest to the DHCP server resided in the network to get an IP address.If DHCP server is down or does not exist, the switch will issue therequest and show IP address is under requesting, until the DHCP serveris up. Before getting an IP address from DHCP server, the device will not34
continue booting procedures. If set this field “Disable”, you’ll have toinput IP address manually. For more details about IP address and DHCP,please see the Section 2-1-5 “IP Address Assignment” in this manual.Default: Disable35
Page 3 and 4: 3-10. VLAN-------------------------
Page 5 and 6: About this user’s manualIn this u
Page 7: • Key Features in the DeviceQoS:S
Page 10 and 11: 1-4. View of 24 Gigabit L2 Managed
Page 12 and 13: 1-5. View of the Optional ModulesIn
Page 14 and 15: • TP Port and Cable Installation
Page 16 and 17: 2-1-3-1. Cabling Requirements for T
Page 18 and 19: Case1: All switch ports are in the
Page 20 and 21: 2-1-4. Configuring the Management A
Page 22 and 23: • Set IP Address, Subnet Mask and
Page 24 and 25: Fig. 2-10 the Login Screen for Web2
Page 26 and 27: Class D and E:Class D is a class wi
Page 28 and 29: For different network applications,
Page 30 and 31: Fig. 2-14 Peer-to-peer Network Conn
Page 32 and 33: In the switch, it supports a simple
Page 34 and 35: • The Information of Page Layout
Page 36 and 37: 3-1-1. System InformationFunction n
Page 40 and 41: IP address:Users can configure the
Page 42 and 43: 3-1-3. Time ConfigurationThe switch
Page 44 and 45: Day Light Saving End :This is used
Page 46 and 47: 3-1-5. Management PolicyThrough the
Page 48 and 49: IP Range:The switch supports two ki
Page 50 and 51: Parameter description:Fig. 3-8State
Page 52 and 53: 3-2. Port ConfigurationFour functio
Page 54 and 55: Speed / Duplex Mode:Display the spe
Page 56 and 57: Vendor SN (Serial Number):Show the
Page 58 and 59: Mode:Set the speed and duplex of th
Page 61 and 62: Rx Packet:The counting number of th
Page 63 and 64: Rx Low Priority Packets:Number of R
Page 65 and 66: 3-3. MirrorFunction name:Mirror Con
Page 67 and 68: Broadcast & Multicasat for Ingress
Page 69 and 70: Function name:Per Port PriorityFunc
Page 71 and 72: Bit 0, Bit 1, Bit 2:According to th
Page 73 and 74: Bit 0, Bit 1, Bit 2:According to th
Page 75 and 76: Prioritize Streaming Audio/Video:Be
Page 77 and 78: Function name:IP Diffserv Classific
Page 79 and 80: Default SNMP function : EnableDefau
Page 81 and 82: Parameter description:IGMP snooping
Page 83 and 84: Add:A new entry of allowed group co
Page 85 and 86: 3-9. DHCP BootThe DHCP Boot functio
Page 87 and 88: Metro Mode:The Metro Mode is a quic
Page 89 and 90:
3-10-2. Tag-based GroupFunction nam
Page 91 and 92:
3-10-3. Port-based GroupFunction na
Page 93 and 94:
modify a group‘s description and
Page 95 and 96:
Role:This is an egress rule of the
Page 97 and 98:
Port:The port that exists in the se
Page 99 and 100:
Function Name:Static ForwardFunctio
Page 101 and 102:
Function name:MAC AliasFunction des
Page 103 and 104:
3-12. GVRP ConfigurationGVRP is an
Page 105 and 106:
Normal:It is Normal Registration. T
Page 107 and 108:
LeaveEmpty Message Packets:Number o
Page 109 and 110:
3-13. STP ConfigurationThe Spanning
Page 111 and 112:
3-13-2. STP ConfigurationThe STP, S
Page 113 and 114:
3-13-3. STP Port ConfigurationFunct
Page 115 and 116:
M Check:Migration Check. It forces
Page 117 and 118:
Per Trunking Group supports a maxim
Page 119 and 120:
Aggtr:Status:Aggtr is an abbreviati
Page 121 and 122:
Function name:LACP Detail (LACP Agg
Page 123 and 124:
3-15. 802.1X Configuration802.1X po
Page 125 and 126:
Authentication serverFig. 3-54CBAut
Page 127 and 128:
Only MultiHost 802.1X is the type o
Page 129 and 130:
Function name:802.1X Mode SettingFu
Page 131 and 132:
Function name:Param. SettingFunctio
Page 133 and 134:
3-16. Alarm ConfigurationAlarm Conf
Page 135 and 136:
Parameter description:Email:Mail Se
Page 137 and 138:
3-17-1. Save/RestoreFunction name:S
Page 139 and 140:
Function name:Restore User Configur
Page 141 and 142:
3-18. DiagnosticsThree functions, i
Page 143 and 144:
Function name:Ping TestFunction des
Page 145 and 146:
3-20. LogThis function shows the lo
Page 147 and 148:
3-21. Firmware UpgradeSoftware upgr
Page 149 and 150:
3-23. LogoutYou can manually logout
Page 151 and 152:
4. Operation of CLIManagement4-1. C
Page 153 and 154:
4-2. Commands of CLITo see the comm
Page 155 and 156:
helpSyntax:helpDescription:To show
Page 157 and 158:
logoutSyntax:logoutDescription:When
Page 159 and 160:
save userSyntax:save userDescriptio
Page 161 and 162:
set port-controlSyntax:set port-con
Page 163 and 164:
set state Description:To configur
Page 165 and 166:
port 2) port control : AutoreAuthMa
Page 167 and 168:
modifySyntax:modify Description:To
Page 169 and 170:
set serverSyntax:set server Descrip
Page 171 and 172:
del trapSyntax:del trap Description
Page 173 and 174:
Example:SNMP-GSH2402(alarm-events)#
Page 175 and 176:
set phone-numberSyntax:set phone-nu
Page 177 and 178:
• bandwidthdisable egress-rateSyn
Page 179 and 180:
showSyntax:showDescription:To displ
Page 181 and 182:
import user-confSyntax:import user-
Page 183 and 184:
• dhcp-bootset dhcp-bootSyntax:se
Page 185 and 186:
• firmwareset upgrade-pathSyntax:
Page 187 and 188:
SNMP-GSH2402(gvrp)# group 2SNMP-GSH
Page 189 and 190:
set restrictedSyntax:set restricted
Page 191 and 192:
show counterSyntax:show counter Des
Page 193 and 194:
set modeSyntax:set mode Description
Page 195 and 196:
set ipSyntax:set ip Description:T
Page 197 and 198:
showSyntax:showDescription:To show
Page 199 and 200:
searchSyntax:search Description:T
Page 201 and 202:
addSyntax:add [alias]Description
Page 203 and 204:
• managementaddSyntax:Usage:set [
Page 205 and 206:
edit [#]: the specific management p
Page 207 and 208:
• max-pkt-lenset lenSyntax:set le
Page 209 and 210:
showSyntax:showDescription:To displ
Page 211 and 212:
enable flow-controlSyntax:enable fl
Page 213 and 214:
Port 23 SFP information------------
Page 215 and 216:
set diffservSyntax:set diffserv De
Page 217 and 218:
set tosSyntax:set tos Description
Page 219 and 220:
setSyntax:set get-community set set
Page 221 and 222:
set configSyntax:set config Desc
Page 223 and 224:
show portSyntax:show portDescriptio
Page 225 and 226:
• systemset contactSyntax:set con
Page 227 and 228:
• tftpset serverSyntax:set server
Page 229 and 230:
set ntpSyntax:set ntp Description:
Page 231 and 232:
show aggtr-viewSyntax:show aggtr-vi
Page 233 and 234:
• vlandel port-groupSyntax:del po
Page 235 and 236:
set modeSyntax:set mode [up-link]D
Page 237 and 238:
set tag-groupSyntax:set tag-group
Page 239 and 240:
• vsdisableSyntax:disableDescript
Page 241 and 242:
5. Maintenance5-1. Resolving No Lin
Page 243 and 244:
Hardware Specifications• Standard
Page 245 and 246:
Management Software SpecificationsA
show all

SNMP-GSH2402 - kamery airlive airlivecam

Create successful ePaper yourself

Delete template?

Save as template?