SNMP-GSH2402 - kamery airlive airlivecam
SNMP-GSH2402 - kamery airlive airlivecam SNMP-GSH2402 - kamery airlive airlivecam
estore userSyntax:restore userDescription:To restore the startup configuration as user defined configuration. If restoring defaultsuccessfully, the CLI would prompt if reboot immediately or not. If you press Y or y,the system would reboot immediately; others would back to the CLI system. Afterrestoring user-defined configuration, all the changes in the startup configurationwould be lost. After rebooting, the entire startup configuration would replace as userdefined one.Argument:None.Possible value:None.Example:SNMP-GSH2402# restore userRestoring ...Restore User Configuration SuccessfullyPress any key to reboot system.save startSyntax:save startDescription:To save the current configuration as the start one. When you enter this command,the CLI would save your current configuration into the non-volatile FLASH. If youwant the configuration still works after rebooting, save the configuration using thecommand ‘save stat’.Argument:None.Possible value:None.Example:SNMP-GSH2402# save startSaving start...Save SuccessfullySNMP-GSH2402#154
save userSyntax:save userDescription:To save the current configuration as the user-defined configuration. When you enterthis command, the CLI would save your current configuration into the non-volatileFLASH as user-defined configuration.Argument:None.Possible value:None.Example:SNMP-GSH2402# save userSaving user...Save SuccessfullySNMP-GSH2402#155
- Page 107 and 108: LeaveEmpty Message Packets:Number o
- Page 109 and 110: 3-13. STP ConfigurationThe Spanning
- Page 111 and 112: 3-13-2. STP ConfigurationThe STP, S
- Page 113 and 114: 3-13-3. STP Port ConfigurationFunct
- Page 115 and 116: M Check:Migration Check. It forces
- Page 117 and 118: Per Trunking Group supports a maxim
- Page 119 and 120: Aggtr:Status:Aggtr is an abbreviati
- Page 121 and 122: Function name:LACP Detail (LACP Agg
- Page 123 and 124: 3-15. 802.1X Configuration802.1X po
- Page 125 and 126: Authentication serverFig. 3-54CBAut
- Page 127 and 128: Only MultiHost 802.1X is the type o
- Page 129 and 130: Function name:802.1X Mode SettingFu
- Page 131 and 132: Function name:Param. SettingFunctio
- Page 133 and 134: 3-16. Alarm ConfigurationAlarm Conf
- Page 135 and 136: Parameter description:Email:Mail Se
- Page 137 and 138: 3-17-1. Save/RestoreFunction name:S
- Page 139 and 140: Function name:Restore User Configur
- Page 141 and 142: 3-18. DiagnosticsThree functions, i
- Page 143 and 144: Function name:Ping TestFunction des
- Page 145 and 146: 3-20. LogThis function shows the lo
- Page 147 and 148: 3-21. Firmware UpgradeSoftware upgr
- Page 149 and 150: 3-23. LogoutYou can manually logout
- Page 151 and 152: 4. Operation of CLIManagement4-1. C
- Page 153 and 154: 4-2. Commands of CLITo see the comm
- Page 155 and 156: helpSyntax:helpDescription:To show
- Page 157: logoutSyntax:logoutDescription:When
- Page 161 and 162: set port-controlSyntax:set port-con
- Page 163 and 164: set state Description:To configur
- Page 165 and 166: port 2) port control : AutoreAuthMa
- Page 167 and 168: modifySyntax:modify Description:To
- Page 169 and 170: set serverSyntax:set server Descrip
- Page 171 and 172: del trapSyntax:del trap Description
- Page 173 and 174: Example:SNMP-GSH2402(alarm-events)#
- Page 175 and 176: set phone-numberSyntax:set phone-nu
- Page 177 and 178: • bandwidthdisable egress-rateSyn
- Page 179 and 180: showSyntax:showDescription:To displ
- Page 181 and 182: import user-confSyntax:import user-
- Page 183 and 184: • dhcp-bootset dhcp-bootSyntax:se
- Page 185 and 186: • firmwareset upgrade-pathSyntax:
- Page 187 and 188: SNMP-GSH2402(gvrp)# group 2SNMP-GSH
- Page 189 and 190: set restrictedSyntax:set restricted
- Page 191 and 192: show counterSyntax:show counter Des
- Page 193 and 194: set modeSyntax:set mode Description
- Page 195 and 196: set ipSyntax:set ip Description:T
- Page 197 and 198: showSyntax:showDescription:To show
- Page 199 and 200: searchSyntax:search Description:T
- Page 201 and 202: addSyntax:add [alias]Description
- Page 203 and 204: • managementaddSyntax:Usage:set [
- Page 205 and 206: edit [#]: the specific management p
- Page 207 and 208: • max-pkt-lenset lenSyntax:set le
save userSyntax:save userDescription:To save the current configuration as the user-defined configuration. When you enterthis command, the CLI would save your current configuration into the non-volatileFLASH as user-defined configuration.Argument:None.Possible value:None.Example:<strong>SNMP</strong>-<strong>GSH2402</strong># save userSaving user...Save Successfully<strong>SNMP</strong>-<strong>GSH2402</strong>#155