SNMP-GSH2402 - kamery airlive airlivecam
SNMP-GSH2402 - kamery airlive airlivecam SNMP-GSH2402 - kamery airlive airlivecam
• TP Port and Cable Installation⇒ In the switch, TP port supports MDI/MDI-X auto-crossover, so both types ofcable, straight-through (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 1, 2, 3, 6 in10/100M TP; 1, 2, 3, 4, 5, 6, 7, 8 to 1, 2, 3, 4, 5, 6, 7, 8 in Gigabit TP) andcrossed-over (Cable pin-outs for RJ-45 jack 1, 2, 3, 6 to 3, 6, 1, 2) can be used.It means you do not have to tell from them, just plug it.⇒ Use Cat. 5 grade RJ-45 TP cable to connect to a TP port of the switch and theother end is connected to a network-aware device such as a workstation or aserver.⇒ Repeat the above steps, as needed, for each RJ-45 port to be connected to aGigabit 10/100/1000 TP device.Now, you can start having the switch in operation.• Power OnThe switch supports 100-240 VAC, 50-60 Hz power supply. The powersupply will automatically convert the local AC power source to DC power. It does notmatter whether any connection plugged into the switch or not when power on, evenmodules as well. After the power is on, all LED indicators will light up immediatelyand then all off except the power LED still keeps on. This represents a reset of thesystem.• Firmware LoadingAfter resetting, the bootloader will load the firmware into the memory. It willtake about 30 seconds, after that, the switch will flash all the LED once andautomatically performs self-test and is in ready state.10
2-1-2. Installing Chassis to a 19-Inch Wiring Closet RailFig. 2-2Caution: Allow a proper spacing and proper air ventilation for the cooling fanat both sides of the chassis.⇒ Wear a grounding device for electrostatic discharge.⇒ Screw the mounting accessory to the front side of the switch (See Fig. 2-2).⇒ Place the Chassis into the 19-inch wiring closet rail and locate it at the properposition. Then, fix the Chassis by screwing it.2-1-3. Cabling RequirementsTo help ensure a successful installation and keep the network performancegood, please take a care on the cabling requirement. Cables with worsespecification will render the LAN to work poorly.11
- Page 3 and 4: 3-10. VLAN-------------------------
- Page 5 and 6: About this user’s manualIn this u
- Page 7: • Key Features in the DeviceQoS:S
- Page 10 and 11: 1-4. View of 24 Gigabit L2 Managed
- Page 12 and 13: 1-5. View of the Optional ModulesIn
- Page 16 and 17: 2-1-3-1. Cabling Requirements for T
- Page 18 and 19: Case1: All switch ports are in the
- Page 20 and 21: 2-1-4. Configuring the Management A
- Page 22 and 23: • Set IP Address, Subnet Mask and
- Page 24 and 25: Fig. 2-10 the Login Screen for Web2
- Page 26 and 27: Class D and E:Class D is a class wi
- Page 28 and 29: For different network applications,
- Page 30 and 31: Fig. 2-14 Peer-to-peer Network Conn
- Page 32 and 33: In the switch, it supports a simple
- Page 34 and 35: • The Information of Page Layout
- Page 36 and 37: 3-1-1. System InformationFunction n
- Page 38 and 39: 3-1-2. IP ConfigurationIP configura
- Page 40 and 41: IP address:Users can configure the
- Page 42 and 43: 3-1-3. Time ConfigurationThe switch
- Page 44 and 45: Day Light Saving End :This is used
- Page 46 and 47: 3-1-5. Management PolicyThrough the
- Page 48 and 49: IP Range:The switch supports two ki
- Page 50 and 51: Parameter description:Fig. 3-8State
- Page 52 and 53: 3-2. Port ConfigurationFour functio
- Page 54 and 55: Speed / Duplex Mode:Display the spe
- Page 56 and 57: Vendor SN (Serial Number):Show the
- Page 58 and 59: Mode:Set the speed and duplex of th
- Page 61 and 62: Rx Packet:The counting number of th
- Page 63 and 64: Rx Low Priority Packets:Number of R
2-1-2. Installing Chassis to a 19-Inch Wiring Closet RailFig. 2-2Caution: Allow a proper spacing and proper air ventilation for the cooling fanat both sides of the chassis.⇒ Wear a grounding device for electrostatic discharge.⇒ Screw the mounting accessory to the front side of the switch (See Fig. 2-2).⇒ Place the Chassis into the 19-inch wiring closet rail and locate it at the properposition. Then, fix the Chassis by screwing it.2-1-3. Cabling RequirementsTo help ensure a successful installation and keep the network performancegood, please take a care on the cabling requirement. Cables with worsespecification will render the LAN to work poorly.11