SNMP-GSH2402 - kamery airlive airlivecam
SNMP-GSH2402 - kamery airlive airlivecam SNMP-GSH2402 - kamery airlive airlivecam
3-22. RebootWe offer you many ways to reboot the switch, including power up, hardwarereset and software reset. You can press the RESET button in the front panel toreset the switch. After upgrading software, changing IP configuration or changingVLAN mode configuration, then you must reboot to have the new configurationtaken effect. Here we are discussing is software reset for the “reboot” in the mainmenu.Function name:RebootFunction description:Reboot the switch. Reboot takes the same effect as the RESET button on thefront panel of the switch. It will take around thirty (30) seconds to complete thesystem boot.Parameter description:Save and Reboot:Reboot:Save the current settings as start configuration before rebooting theswitch.Reboot the system directly.Fig. 3-75144
3-23. LogoutYou can manually logout by performing Logout function. In the switch, itprovides another way to logout. You can configure it to logout automatically.Function name:LogoutFunction description:The switch allows you to logout the system to prevent other users from thesystem without the permission. If you do not logout and exit the browser, theswitch will automatically have you logout. Besides this manually logout andimplicit logout, you can pull down the list at the top-left cornerto explicitly ON/OFF this logout function.Parameter description:Auto Logout:Default is ON. If it is “ON”, and no action and no key is stroke as well inany function screen more than 3 minutes, the switch will have you logoutautomatically.Fig. 3-76145
- Page 97 and 98: Port:The port that exists in the se
- Page 99 and 100: Function Name:Static ForwardFunctio
- Page 101 and 102: Function name:MAC AliasFunction des
- Page 103 and 104: 3-12. GVRP ConfigurationGVRP is an
- Page 105 and 106: Normal:It is Normal Registration. T
- Page 107 and 108: LeaveEmpty Message Packets:Number o
- Page 109 and 110: 3-13. STP ConfigurationThe Spanning
- Page 111 and 112: 3-13-2. STP ConfigurationThe STP, S
- Page 113 and 114: 3-13-3. STP Port ConfigurationFunct
- Page 115 and 116: M Check:Migration Check. It forces
- Page 117 and 118: Per Trunking Group supports a maxim
- Page 119 and 120: Aggtr:Status:Aggtr is an abbreviati
- Page 121 and 122: Function name:LACP Detail (LACP Agg
- Page 123 and 124: 3-15. 802.1X Configuration802.1X po
- Page 125 and 126: Authentication serverFig. 3-54CBAut
- Page 127 and 128: Only MultiHost 802.1X is the type o
- Page 129 and 130: Function name:802.1X Mode SettingFu
- Page 131 and 132: Function name:Param. SettingFunctio
- Page 133 and 134: 3-16. Alarm ConfigurationAlarm Conf
- Page 135 and 136: Parameter description:Email:Mail Se
- Page 137 and 138: 3-17-1. Save/RestoreFunction name:S
- Page 139 and 140: Function name:Restore User Configur
- Page 141 and 142: 3-18. DiagnosticsThree functions, i
- Page 143 and 144: Function name:Ping TestFunction des
- Page 145 and 146: 3-20. LogThis function shows the lo
- Page 147: 3-21. Firmware UpgradeSoftware upgr
- Page 151 and 152: 4. Operation of CLIManagement4-1. C
- Page 153 and 154: 4-2. Commands of CLITo see the comm
- Page 155 and 156: helpSyntax:helpDescription:To show
- Page 157 and 158: logoutSyntax:logoutDescription:When
- Page 159 and 160: save userSyntax:save userDescriptio
- Page 161 and 162: set port-controlSyntax:set port-con
- Page 163 and 164: set state Description:To configur
- Page 165 and 166: port 2) port control : AutoreAuthMa
- Page 167 and 168: modifySyntax:modify Description:To
- Page 169 and 170: set serverSyntax:set server Descrip
- Page 171 and 172: del trapSyntax:del trap Description
- Page 173 and 174: Example:SNMP-GSH2402(alarm-events)#
- Page 175 and 176: set phone-numberSyntax:set phone-nu
- Page 177 and 178: • bandwidthdisable egress-rateSyn
- Page 179 and 180: showSyntax:showDescription:To displ
- Page 181 and 182: import user-confSyntax:import user-
- Page 183 and 184: • dhcp-bootset dhcp-bootSyntax:se
- Page 185 and 186: • firmwareset upgrade-pathSyntax:
- Page 187 and 188: SNMP-GSH2402(gvrp)# group 2SNMP-GSH
- Page 189 and 190: set restrictedSyntax:set restricted
- Page 191 and 192: show counterSyntax:show counter Des
- Page 193 and 194: set modeSyntax:set mode Description
- Page 195 and 196: set ipSyntax:set ip Description:T
- Page 197 and 198: showSyntax:showDescription:To show
3-23. LogoutYou can manually logout by performing Logout function. In the switch, itprovides another way to logout. You can configure it to logout automatically.Function name:LogoutFunction description:The switch allows you to logout the system to prevent other users from thesystem without the permission. If you do not logout and exit the browser, theswitch will automatically have you logout. Besides this manually logout andimplicit logout, you can pull down the list at the top-left cornerto explicitly ON/OFF this logout function.Parameter description:Auto Logout:Default is ON. If it is “ON”, and no action and no key is stroke as well inany function screen more than 3 minutes, the switch will have you logoutautomatically.Fig. 3-76145