SNMP-GSH2402 - kamery airlive airlivecam
SNMP-GSH2402 - kamery airlive airlivecam SNMP-GSH2402 - kamery airlive airlivecam
Fig. 3-60Function name:Email/SMS ConfigurationFunction description:Alarm configuration is used to configure the persons who should receive thealarm message via either email or SMS, or both. It depends on your settings.An email address or a mobile phone number has to be set in the web page ofalarm configuration (See Fig. 3-61). Then, user can read the trap informationfrom the email or the mobile phone. This function provides 6 email addressesand 6 mobile phone numbers at most. The 24 different trap events will be sentout to SNMP Manager when trap event occurs. After ticking trap events, youcan fill in your desired email addresses and mobile phone numbers. Then,please click button to complete the alarm configuration. It will takeeffect in a few seconds.Note: SMS may not work in your mobile phone system. It is customized for differentsystems.130
Parameter description:Email:Mail Server: the IP address of the server transferring your email.Username: your username on the mail server.Password: your password on the mail server.Email Address 1 – 6: email address that would like to receive thealarm message.SMS:SMS Server: the IP address of the server transferring your SMS.Username: your username in ISP.Password: your username in ISP.Mobile Phone 1-6: the mobile phone number that would like toreceive the alarm message.Fig. 3-61131
- Page 83 and 84: Add:A new entry of allowed group co
- Page 85 and 86: 3-9. DHCP BootThe DHCP Boot functio
- Page 87 and 88: Metro Mode:The Metro Mode is a quic
- Page 89 and 90: 3-10-2. Tag-based GroupFunction nam
- Page 91 and 92: 3-10-3. Port-based GroupFunction na
- Page 93 and 94: modify a group‘s description and
- Page 95 and 96: Role:This is an egress rule of the
- Page 97 and 98: Port:The port that exists in the se
- Page 99 and 100: Function Name:Static ForwardFunctio
- Page 101 and 102: Function name:MAC AliasFunction des
- Page 103 and 104: 3-12. GVRP ConfigurationGVRP is an
- Page 105 and 106: Normal:It is Normal Registration. T
- Page 107 and 108: LeaveEmpty Message Packets:Number o
- Page 109 and 110: 3-13. STP ConfigurationThe Spanning
- Page 111 and 112: 3-13-2. STP ConfigurationThe STP, S
- Page 113 and 114: 3-13-3. STP Port ConfigurationFunct
- Page 115 and 116: M Check:Migration Check. It forces
- Page 117 and 118: Per Trunking Group supports a maxim
- Page 119 and 120: Aggtr:Status:Aggtr is an abbreviati
- Page 121 and 122: Function name:LACP Detail (LACP Agg
- Page 123 and 124: 3-15. 802.1X Configuration802.1X po
- Page 125 and 126: Authentication serverFig. 3-54CBAut
- Page 127 and 128: Only MultiHost 802.1X is the type o
- Page 129 and 130: Function name:802.1X Mode SettingFu
- Page 131 and 132: Function name:Param. SettingFunctio
- Page 133: 3-16. Alarm ConfigurationAlarm Conf
- Page 137 and 138: 3-17-1. Save/RestoreFunction name:S
- Page 139 and 140: Function name:Restore User Configur
- Page 141 and 142: 3-18. DiagnosticsThree functions, i
- Page 143 and 144: Function name:Ping TestFunction des
- Page 145 and 146: 3-20. LogThis function shows the lo
- Page 147 and 148: 3-21. Firmware UpgradeSoftware upgr
- Page 149 and 150: 3-23. LogoutYou can manually logout
- Page 151 and 152: 4. Operation of CLIManagement4-1. C
- Page 153 and 154: 4-2. Commands of CLITo see the comm
- Page 155 and 156: helpSyntax:helpDescription:To show
- Page 157 and 158: logoutSyntax:logoutDescription:When
- Page 159 and 160: save userSyntax:save userDescriptio
- Page 161 and 162: set port-controlSyntax:set port-con
- Page 163 and 164: set state Description:To configur
- Page 165 and 166: port 2) port control : AutoreAuthMa
- Page 167 and 168: modifySyntax:modify Description:To
- Page 169 and 170: set serverSyntax:set server Descrip
- Page 171 and 172: del trapSyntax:del trap Description
- Page 173 and 174: Example:SNMP-GSH2402(alarm-events)#
- Page 175 and 176: set phone-numberSyntax:set phone-nu
- Page 177 and 178: • bandwidthdisable egress-rateSyn
- Page 179 and 180: showSyntax:showDescription:To displ
- Page 181 and 182: import user-confSyntax:import user-
- Page 183 and 184: • dhcp-bootset dhcp-bootSyntax:se
Parameter description:Email:Mail Server: the IP address of the server transferring your email.Username: your username on the mail server.Password: your password on the mail server.Email Address 1 – 6: email address that would like to receive thealarm message.SMS:SMS Server: the IP address of the server transferring your SMS.Username: your username in ISP.Password: your username in ISP.Mobile Phone 1-6: the mobile phone number that would like toreceive the alarm message.Fig. 3-61131