SNMP-GSH2402 - kamery airlive airlivecam

More documents

Recommendations

Info

Function name:802.1X State SettingFunction description:This function is used to configure the global parameters for RADIUSauthentication in 802.1X port security application.Parameter description:Radius Server:RADIUS server IP address for authentication.Default: 192.168.1.1Port Number:The port number to communicate with RADIUS server for theauthentication service. The valid value ranges 1-65535.Default port number is 1812.Secret Key:The secret key between authentication server and authenticator. It is astring with the length 1 – 31 characters. The character string may containupper case, lower case and 0-9. It is character sense. It is not allowed forputting a blank between any two characters.Default: RadiusFig. 3-56124
Function name:802.1X Mode SettingFunction description:Set the operation mode of 802.1X for each port. In this device, it supports onlyMulti-host operation mode.Parameter description:Port Number:Indicate which port is selected to configure the 802.1X operation mode.802.1X Mode:802.1X operation mode. There are two options, including Disable andMulti-host mode. Default is Disable.• DisableIt will have the chosen port acting as a plain port, that is no 802.1Xport access control works on the port.• 802.1X with Multi-hostIn Multi-host mode, for the devices connected to this port, once asupplicant is authorized, the devices connected to this port can accessthe network resource through this port.Fig. 3-57125
Page 3 and 4:
3-10. VLAN-------------------------
Page 5 and 6:
About this user’s manualIn this u
Page 7:
• Key Features in the DeviceQoS:S
Page 10 and 11:
1-4. View of 24 Gigabit L2 Managed
Page 12 and 13:
1-5. View of the Optional ModulesIn
Page 14 and 15:
• TP Port and Cable Installation
Page 16 and 17:
2-1-3-1. Cabling Requirements for T
Page 18 and 19:
Case1: All switch ports are in the
Page 20 and 21:
2-1-4. Configuring the Management A
Page 22 and 23:
• Set IP Address, Subnet Mask and
Page 24 and 25:
Fig. 2-10 the Login Screen for Web2
Page 26 and 27:
Class D and E:Class D is a class wi
Page 28 and 29:
For different network applications,
Page 30 and 31:
Fig. 2-14 Peer-to-peer Network Conn
Page 32 and 33:
In the switch, it supports a simple
Page 34 and 35:
• The Information of Page Layout
Page 36 and 37:
3-1-1. System InformationFunction n
Page 38 and 39:
3-1-2. IP ConfigurationIP configura
Page 40 and 41:
IP address:Users can configure the
Page 42 and 43:
3-1-3. Time ConfigurationThe switch
Page 44 and 45:
Day Light Saving End :This is used
Page 46 and 47:
3-1-5. Management PolicyThrough the
Page 48 and 49:
IP Range:The switch supports two ki
Page 50 and 51:
Parameter description:Fig. 3-8State
Page 52 and 53:
3-2. Port ConfigurationFour functio
Page 54 and 55:
Speed / Duplex Mode:Display the spe
Page 56 and 57:
Vendor SN (Serial Number):Show the
Page 58 and 59:
Mode:Set the speed and duplex of th
Page 61 and 62:
Rx Packet:The counting number of th
Page 63 and 64:
Rx Low Priority Packets:Number of R
Page 65 and 66:
3-3. MirrorFunction name:Mirror Con
Page 67 and 68:
Broadcast & Multicasat for Ingress
Page 69 and 70:
Function name:Per Port PriorityFunc
Page 71 and 72:
Bit 0, Bit 1, Bit 2:According to th
Page 73 and 74:
Bit 0, Bit 1, Bit 2:According to th
Page 75 and 76:
Prioritize Streaming Audio/Video:Be
Page 77 and 78: Function name:IP Diffserv Classific
Page 79 and 80: Default SNMP function : EnableDefau
Page 81 and 82: Parameter description:IGMP snooping
Page 83 and 84: Add:A new entry of allowed group co
Page 85 and 86: 3-9. DHCP BootThe DHCP Boot functio
Page 87 and 88: Metro Mode:The Metro Mode is a quic
Page 89 and 90: 3-10-2. Tag-based GroupFunction nam
Page 91 and 92: 3-10-3. Port-based GroupFunction na
Page 93 and 94: modify a group‘s description and
Page 95 and 96: Role:This is an egress rule of the
Page 97 and 98: Port:The port that exists in the se
Page 99 and 100: Function Name:Static ForwardFunctio
Page 101 and 102: Function name:MAC AliasFunction des
Page 103 and 104: 3-12. GVRP ConfigurationGVRP is an
Page 105 and 106: Normal:It is Normal Registration. T
Page 107 and 108: LeaveEmpty Message Packets:Number o
Page 109 and 110: 3-13. STP ConfigurationThe Spanning
Page 111 and 112: 3-13-2. STP ConfigurationThe STP, S
Page 113 and 114: 3-13-3. STP Port ConfigurationFunct
Page 115 and 116: M Check:Migration Check. It forces
Page 117 and 118: Per Trunking Group supports a maxim
Page 119 and 120: Aggtr:Status:Aggtr is an abbreviati
Page 121 and 122: Function name:LACP Detail (LACP Agg
Page 123 and 124: 3-15. 802.1X Configuration802.1X po
Page 125 and 126: Authentication serverFig. 3-54CBAut
Page 127: Only MultiHost 802.1X is the type o
Page 131 and 132: Function name:Param. SettingFunctio
Page 133 and 134: 3-16. Alarm ConfigurationAlarm Conf
Page 135 and 136: Parameter description:Email:Mail Se
Page 137 and 138: 3-17-1. Save/RestoreFunction name:S
Page 139 and 140: Function name:Restore User Configur
Page 141 and 142: 3-18. DiagnosticsThree functions, i
Page 143 and 144: Function name:Ping TestFunction des
Page 145 and 146: 3-20. LogThis function shows the lo
Page 147 and 148: 3-21. Firmware UpgradeSoftware upgr
Page 149 and 150: 3-23. LogoutYou can manually logout
Page 151 and 152: 4. Operation of CLIManagement4-1. C
Page 153 and 154: 4-2. Commands of CLITo see the comm
Page 155 and 156: helpSyntax:helpDescription:To show
Page 157 and 158: logoutSyntax:logoutDescription:When
Page 159 and 160: save userSyntax:save userDescriptio
Page 161 and 162: set port-controlSyntax:set port-con
Page 163 and 164: set state Description:To configur
Page 165 and 166: port 2) port control : AutoreAuthMa
Page 167 and 168: modifySyntax:modify Description:To
Page 169 and 170: set serverSyntax:set server Descrip
Page 171 and 172: del trapSyntax:del trap Description
Page 173 and 174: Example:SNMP-GSH2402(alarm-events)#
Page 175 and 176: set phone-numberSyntax:set phone-nu
Page 177 and 178: • bandwidthdisable egress-rateSyn
Page 179 and 180:
showSyntax:showDescription:To displ
Page 181 and 182:
import user-confSyntax:import user-
Page 183 and 184:
• dhcp-bootset dhcp-bootSyntax:se
Page 185 and 186:
• firmwareset upgrade-pathSyntax:
Page 187 and 188:
SNMP-GSH2402(gvrp)# group 2SNMP-GSH
Page 189 and 190:
set restrictedSyntax:set restricted
Page 191 and 192:
show counterSyntax:show counter Des
Page 193 and 194:
set modeSyntax:set mode Description
Page 195 and 196:
set ipSyntax:set ip Description:T
Page 197 and 198:
showSyntax:showDescription:To show
Page 199 and 200:
searchSyntax:search Description:T
Page 201 and 202:
addSyntax:add [alias]Description
Page 203 and 204:
• managementaddSyntax:Usage:set [
Page 205 and 206:
edit [#]: the specific management p
Page 207 and 208:
• max-pkt-lenset lenSyntax:set le
Page 209 and 210:
showSyntax:showDescription:To displ
Page 211 and 212:
enable flow-controlSyntax:enable fl
Page 213 and 214:
Port 23 SFP information------------
Page 215 and 216:
set diffservSyntax:set diffserv De
Page 217 and 218:
set tosSyntax:set tos Description
Page 219 and 220:
setSyntax:set get-community set set
Page 221 and 222:
set configSyntax:set config Desc
Page 223 and 224:
show portSyntax:show portDescriptio
Page 225 and 226:
• systemset contactSyntax:set con
Page 227 and 228:
• tftpset serverSyntax:set server
Page 229 and 230:
set ntpSyntax:set ntp Description:
Page 231 and 232:
show aggtr-viewSyntax:show aggtr-vi
Page 233 and 234:
• vlandel port-groupSyntax:del po
Page 235 and 236:
set modeSyntax:set mode [up-link]D
Page 237 and 238:
set tag-groupSyntax:set tag-group
Page 239 and 240:
• vsdisableSyntax:disableDescript
Page 241 and 242:
5. Maintenance5-1. Resolving No Lin
Page 243 and 244:
Hardware Specifications• Standard
Page 245 and 246:
Management Software SpecificationsA
show all

SNMP-GSH2402 - kamery airlive airlivecam

Create successful ePaper yourself

Delete template?

Save as template?