SNMP-GSH2402 - kamery airlive airlivecam
SNMP-GSH2402 - kamery airlive airlivecam SNMP-GSH2402 - kamery airlive airlivecam
Function name:Aggregator ViewFunction description:To display the current port trunking information from the aggregator point ofview.Parameter description:Aggregator:Method:It shows the aggregator ID (from 1 to 24) of every port. In fact, every portis also an aggregator, and its own aggregator ID is the same as its ownPort No..Show the method a port uses to aggregate with other ports.Member Ports:Show all member ports of an aggregator (port).Ready Ports:Show only the ready member ports within an aggregator (port).Fig.3-50116
Function name:LACP Detail (LACP Aggregator Detailed Information)Function description:Show the detailed information of the LACP trunking group.Parameter description:Actor:The switch you are watching on.Partner:The peer system from this aggregator’s view.System Priority:Show the System Priority part of a system ID.MAC Address:Port:Key:Show the MAC Address part of a system ID.Show the port number part of an LACP port ID.Show the key value of the aggregator. The key value is determined bythe LACP protocol entity and can’t be set through management.Trunk Status:Show the trunk status of a single member port.”---“ means “not ready”Fig. 4-51117
- Page 69 and 70: Function name:Per Port PriorityFunc
- Page 71 and 72: Bit 0, Bit 1, Bit 2:According to th
- Page 73 and 74: Bit 0, Bit 1, Bit 2:According to th
- Page 75 and 76: Prioritize Streaming Audio/Video:Be
- Page 77 and 78: Function name:IP Diffserv Classific
- Page 79 and 80: Default SNMP function : EnableDefau
- Page 81 and 82: Parameter description:IGMP snooping
- Page 83 and 84: Add:A new entry of allowed group co
- Page 85 and 86: 3-9. DHCP BootThe DHCP Boot functio
- Page 87 and 88: Metro Mode:The Metro Mode is a quic
- Page 89 and 90: 3-10-2. Tag-based GroupFunction nam
- Page 91 and 92: 3-10-3. Port-based GroupFunction na
- Page 93 and 94: modify a group‘s description and
- Page 95 and 96: Role:This is an egress rule of the
- Page 97 and 98: Port:The port that exists in the se
- Page 99 and 100: Function Name:Static ForwardFunctio
- Page 101 and 102: Function name:MAC AliasFunction des
- Page 103 and 104: 3-12. GVRP ConfigurationGVRP is an
- Page 105 and 106: Normal:It is Normal Registration. T
- Page 107 and 108: LeaveEmpty Message Packets:Number o
- Page 109 and 110: 3-13. STP ConfigurationThe Spanning
- Page 111 and 112: 3-13-2. STP ConfigurationThe STP, S
- Page 113 and 114: 3-13-3. STP Port ConfigurationFunct
- Page 115 and 116: M Check:Migration Check. It forces
- Page 117 and 118: Per Trunking Group supports a maxim
- Page 119: Aggtr:Status:Aggtr is an abbreviati
- Page 123 and 124: 3-15. 802.1X Configuration802.1X po
- Page 125 and 126: Authentication serverFig. 3-54CBAut
- Page 127 and 128: Only MultiHost 802.1X is the type o
- Page 129 and 130: Function name:802.1X Mode SettingFu
- Page 131 and 132: Function name:Param. SettingFunctio
- Page 133 and 134: 3-16. Alarm ConfigurationAlarm Conf
- Page 135 and 136: Parameter description:Email:Mail Se
- Page 137 and 138: 3-17-1. Save/RestoreFunction name:S
- Page 139 and 140: Function name:Restore User Configur
- Page 141 and 142: 3-18. DiagnosticsThree functions, i
- Page 143 and 144: Function name:Ping TestFunction des
- Page 145 and 146: 3-20. LogThis function shows the lo
- Page 147 and 148: 3-21. Firmware UpgradeSoftware upgr
- Page 149 and 150: 3-23. LogoutYou can manually logout
- Page 151 and 152: 4. Operation of CLIManagement4-1. C
- Page 153 and 154: 4-2. Commands of CLITo see the comm
- Page 155 and 156: helpSyntax:helpDescription:To show
- Page 157 and 158: logoutSyntax:logoutDescription:When
- Page 159 and 160: save userSyntax:save userDescriptio
- Page 161 and 162: set port-controlSyntax:set port-con
- Page 163 and 164: set state Description:To configur
- Page 165 and 166: port 2) port control : AutoreAuthMa
- Page 167 and 168: modifySyntax:modify Description:To
- Page 169 and 170: set serverSyntax:set server Descrip
Function name:Aggregator ViewFunction description:To display the current port trunking information from the aggregator point ofview.Parameter description:Aggregator:Method:It shows the aggregator ID (from 1 to 24) of every port. In fact, every portis also an aggregator, and its own aggregator ID is the same as its ownPort No..Show the method a port uses to aggregate with other ports.Member Ports:Show all member ports of an aggregator (port).Ready Ports:Show only the ready member ports within an aggregator (port).Fig.3-50116