Windows Setup Guide for ST-B10 - Toshiba Tec
Windows Setup Guide for ST-B10 - Toshiba Tec Windows Setup Guide for ST-B10 - Toshiba Tec
Windows Setup Guide for ST-B10TOSHIBA TEC CORPORATION EAA-03033The following calibration screen appears. Perform a calibration by touching the mark wheneverit appears. (The mark appears three times.)Note:The calibration screen appears one time each a touch panel. The calibration screenappears two times at two touch panels.In the case of Dual Display, please refer to the table as below.Remainder to use two touch panelsDisplay modesRemainder of CalibrationThe calibration screen appears on both panels two times. When youClone calibrate touch panels, sequence of calibration does not make anydifference.ExtendeddesktopThe calibration screen appears Primary display. After that, the screenappears Secondary display.Remainder to use single touch panel and another non-touch displayDisplay modesRemainder of CalibrationCloneExtendeddesktopThe calibration screen appears both monitors. Please calibrate touchpanel.The calibration screen appears Primary display.If Secondary display is touch panel, press “Esc” key from keyboard. Thecalibration screen appears Secondary display.55
Windows Setup Guide for ST-B10TOSHIBA TEC CORPORATION EAA-03033After the mark was touched three times, two buttons appear at the center of the screen. Click onthe check mark button to complete the calibration.If using dual touch panel, the calibration screen re-appears.56
- Page 7 and 8: Windows Setup Guide for ST-B10TOSHI
- Page 9 and 10: Windows Setup Guide for ST-B10TOSHI
- Page 11 and 12: Windows Setup Guide for ST-B10TOSHI
- Page 13 and 14: Windows Setup Guide for ST-B10TOSHI
- Page 15 and 16: Windows Setup Guide for ST-B10TOSHI
- Page 17 and 18: Windows Setup Guide for ST-B10TOSHI
- Page 19 and 20: Windows Setup Guide for ST-B10TOSHI
- Page 21 and 22: Windows Setup Guide for ST-B10TOSHI
- Page 23 and 24: Windows Setup Guide for ST-B10TOSHI
- Page 25 and 26: Windows Setup Guide for ST-B10TOSHI
- Page 27 and 28: Windows Setup Guide for ST-B10TOSHI
- Page 29 and 30: Windows Setup Guide for ST-B10TOSHI
- Page 31 and 32: Windows Setup Guide for ST-B10TOSHI
- Page 33 and 34: Windows Setup Guide for ST-B10TOSHI
- Page 35 and 36: Windows Setup Guide for ST-B10TOSHI
- Page 37 and 38: Windows Setup Guide for ST-B10TOSHI
- Page 39 and 40: Windows Setup Guide for ST-B10TOSHI
- Page 41 and 42: Windows Setup Guide for ST-B10TOSHI
- Page 43 and 44: Windows Setup Guide for ST-B10TOSHI
- Page 45 and 46: Windows Setup Guide for ST-B10TOSHI
- Page 47 and 48: Windows Setup Guide for ST-B10TOSHI
- Page 49 and 50: Windows Setup Guide for ST-B10TOSHI
- Page 51 and 52: Windows Setup Guide for ST-B10TOSHI
- Page 53 and 54: Windows Setup Guide for ST-B10TOSHI
- Page 55 and 56: Windows Setup Guide for ST-B10TOSHI
- Page 57: Windows Setup Guide for ST-B10TOSHI
- Page 61 and 62: Windows Setup Guide for ST-B10TOSHI
- Page 63 and 64: Windows Setup Guide for ST-B10TOSHI
- Page 65 and 66: Windows Setup Guide for ST-B10TOSHI
- Page 67 and 68: Windows Setup Guide for ST-B10TOSHI
- Page 69 and 70: Windows Setup Guide for ST-B10TOSHI
- Page 71 and 72: Windows Setup Guide for ST-B10TOSHI
- Page 73 and 74: Windows Setup Guide for ST-B10TOSHI
- Page 75 and 76: Windows Setup Guide for ST-B10TOSHI
- Page 77 and 78: Windows Setup Guide for ST-B10TOSHI
- Page 79 and 80: Windows Setup Guide for ST-B10TOSHI
<strong>Windows</strong> <strong>Setup</strong> <strong>Guide</strong> <strong>for</strong> <strong>ST</strong>-<strong>B10</strong>TOSHIBA TEC CORPORATION EAA-03033After the mark was touched three times, two buttons appear at the center of the screen. Click onthe check mark button to complete the calibration.If using dual touch panel, the calibration screen re-appears.56