Manitowoc
Manitowoc Manitowoc
from basequipment.com
More from this publisher
12.07.2015
Views
SUMP DRAIN OVERFLOW TUBE1. Remove clamp.2. Pull down to remove overflow tube and tubing asan assembly. The sump trough water will draininto the bin.3. Remove overflow tube from vinyl tubing bypulling.REMOVE CLAMPANDPULL DOWN72 Part Number 80-01111-9 7/10
WATER TROUGH1. Depress tabs on right and left side of the watertrough.2. Allow front of water trough to drop as you pullforward to disengage the rear pins.Part Number 80-01111-9 7/10 73
- Page 22 and 23: How State Law AppliesThis limited w
- Page 24 and 25: Ice Machine Clearance RequirementsS
- Page 26 and 27: SM50/QM20/QM30After moving the ice
- Page 28 and 29: Electrical SpecificationsQ130/Q170/
- Page 30 and 31: QM20/QM30/QM45 Air-cooled Ice Machi
- Page 32 and 33: COOLING TOWER APPLICATIONSWater Coo
- Page 34 and 35: QM20/QM30LocationIce MakingWater In
- Page 36 and 37: This Page Intentionally Left Blank3
- Page 38 and 39: ON/OFF/WASHTOGGLESWITCHCONDENSER AI
- Page 40 and 41: ON/OFF/WASHTOGGLESWITCHQM20 Ice Mac
- Page 42 and 43: WATERPUMPEVAPORATORWATERSHUTTERASSE
- Page 44 and 45: AIR-COOLED CONDENSERA dirty condens
- Page 46 and 47: Step 1 Set the toggle switch to the
- Page 48 and 49: D. Remove the Ice Thickness Probe
- Page 50 and 51: Disassembly• Twist both of the in
- Page 52 and 53: F. Remove the Float Valve• Turn t
- Page 54 and 55: H. Remove the ice damper.Q130• Gr
- Page 56 and 57: I. Remove the Bin Door• Grasp the
- Page 58 and 59: Step 12 Use 1/2 of the sanitizer/wa
- Page 60 and 61: QM20/QM30CLEANING AND SANITIZING PR
- Page 62 and 63: Step 6 Remove parts for cleaning.A.
- Page 64 and 65: Step 7 Mix a solution of cleaner an
- Page 66 and 67: Step 20 Use half of the sanitizer/w
- Page 68 and 69: 4. Wait until the Clean light flash
- Page 70 and 71: WATER SHUTTERSThe water shutter is
- Page 74 and 75: SPRAY BAR, WATER PUMP AND HOSE! War
- Page 76 and 77: ! WarningWear ru bber gloves an d s
- Page 78 and 79: WATER-COOLED ICE MACHINES1. Perform
- Page 80 and 81: HARVEST SEQUENCE5. HarvestThe water
- Page 82 and 83: ICE MAKINGSEQUENCE OFOPERATIONHarve
- Page 84 and 85: HARVEST SEQUENCE4. Harvest CycleThe
- Page 86 and 87: SM50INITIAL START-UP OR START-UP AF
- Page 88 and 89: ENERGIZED PARTS CHARTSM50Self-conta
- Page 90 and 91: Water Level CheckThe float valve is
- Page 92 and 93: QM20/QM30Routine adjustments and ma
- Page 94 and 95: 5. Remove the two screws holding th
- Page 96 and 97: Clean (Green)Pressing the “Clean
- Page 98 and 99: This Page Intentionally Left Blank9
- Page 100 and 101: DIAGNOSING ICE THICKNESS CONTROLCIR
- Page 102 and 103: Ice Machine Cycles Into Harvest Bef
- Page 104 and 105: INSTALLATION AND VISUAL INSPECTIONC
- Page 106 and 107: ICE FORMATION PATTERNEvaporator ice
- Page 108 and 109: SAFETY LIMIT FEATUREIn addition to
- Page 110 and 111: Safety Limit Notes• A safety limi
- Page 112 and 113: Safety Limit ChecklistThe following
- Page 114 and 115: Safety Limit #2Harvest time exceeds
- Page 116 and 117: Discharge Pressure High ChecklistIm
- Page 118 and 119: ProcedureStep1. Determine the ice m
- Page 120 and 121: Suction Pressure Low ChecklistImpro
WATER TROUGH1. Depress tabs on right and left side of the watertrough.2. Allow front of water trough to drop as you pullforward to disengage the rear pins.Part Number 80-01111-9 7/10 73
Change language