Manitowoc
Manitowoc Manitowoc
I. Remove the Bin Door• Grasp the rear of the bin door and pull bin doorforward approximately 5".• Slide bin door to the rear while applying upwardpressure (The rear door pins will ride up into the trackslot and slide backward to the stop tab).• While applying pressure against the bin door pulldown on the rear of each bin door track until the doorpins clear the stop tabs.• Slide the rear door pins off the end and then belowthe door track. Slide bin door forward allowing theback of the door to lower into the bin. Continueforward with the bin door until the front pins bottomout in the track.• Lift right side of door until the front pins clear thetrack, then remove door from bin.• Remove rollers (4) from all door pins.STOP TABTRACK SLOTSLIDE DOORFORWARDSV174856 Part Number 80-01111-9 7/10
Step 7 Mix a solution of cleaner and warm water.Depending on the amount of mineral buildup, a largerquantity of solution may be required. Use the ratio inthe table below to mix enough solution to thoroughlyclean all parts.SolutionWaterMixed withTypeCleaner 1 gal. (4 l) 16 oz (500 ml) cleanerStep 8 Use ½ of the cleaner/water solution to cleanall components. The cleaner solution will foam when itcontacts lime scale and mineral deposits; once thefoaming stops use a soft bristle brush, sponge or cloth(not a wire brush) to carefully clean the parts. Soak theparts for 5 minutes (15 – 20 minutes for heavily scaledparts). Rinse all components with clean water.Step 9 While components are soaking, use ½ of thecleaner/water solution to clean all foodzone surfacesof the ice machine and bin. Use a nylon brush or clothto thoroughly clean the following ice machine areas:• Evaporator plastic parts – including top, bottomand sides• Bin bottom, sides and topRinse all areas thoroughly with clean water.Step 10 Mix a solution of sanitizer and warm water.SolutionTypeWaterMixed WithSanitizer 6 gal. (23 l) 4 oz (120 ml) sanitizerStep 11 Use 1/2 of the sanitizer/water solution tosanitize all removed components. Use a cloth orsponge to liberally apply the solution to all surfaces ofthe removed parts or soak the removed parts in thesanitizer/water solution. Do not rinse parts aftersanitizing.Part Number 80-01111-9 7/10 57
- Page 6 and 7: Cleaning the Condenser . . . . . .
- Page 8 and 9: Freeze Cycle Is Long, Low Ice Produ
- Page 10 and 11: CHARTSCycle Times, 24 Hr. Ice Produ
- Page 12 and 13: How to Read a Model NumberCube Size
- Page 14 and 15: Model/Serial Number LocationThe mod
- Page 16 and 17: SM50MODEL/SERIALNUMBER PLATE16 Part
- Page 18 and 19: LaborQ130/Q170/Q210/Q2701. Labor re
- Page 20 and 21: RESIDENTIAL WARRANTY COVERAGEWhat D
- Page 22 and 23: How State Law AppliesThis limited w
- Page 24 and 25: Ice Machine Clearance RequirementsS
- Page 26 and 27: SM50/QM20/QM30After moving the ice
- Page 28 and 29: Electrical SpecificationsQ130/Q170/
- Page 30 and 31: QM20/QM30/QM45 Air-cooled Ice Machi
- Page 32 and 33: COOLING TOWER APPLICATIONSWater Coo
- Page 34 and 35: QM20/QM30LocationIce MakingWater In
- Page 36 and 37: This Page Intentionally Left Blank3
- Page 38 and 39: ON/OFF/WASHTOGGLESWITCHCONDENSER AI
- Page 40 and 41: ON/OFF/WASHTOGGLESWITCHQM20 Ice Mac
- Page 42 and 43: WATERPUMPEVAPORATORWATERSHUTTERASSE
- Page 44 and 45: AIR-COOLED CONDENSERA dirty condens
- Page 46 and 47: Step 1 Set the toggle switch to the
- Page 48 and 49: D. Remove the Ice Thickness Probe
- Page 50 and 51: Disassembly• Twist both of the in
- Page 52 and 53: F. Remove the Float Valve• Turn t
- Page 54 and 55: H. Remove the ice damper.Q130• Gr
- Page 58 and 59: Step 12 Use 1/2 of the sanitizer/wa
- Page 60 and 61: QM20/QM30CLEANING AND SANITIZING PR
- Page 62 and 63: Step 6 Remove parts for cleaning.A.
- Page 64 and 65: Step 7 Mix a solution of cleaner an
- Page 66 and 67: Step 20 Use half of the sanitizer/w
- Page 68 and 69: 4. Wait until the Clean light flash
- Page 70 and 71: WATER SHUTTERSThe water shutter is
- Page 72 and 73: SUMP DRAIN OVERFLOW TUBE1. Remove c
- Page 74 and 75: SPRAY BAR, WATER PUMP AND HOSE! War
- Page 76 and 77: ! WarningWear ru bber gloves an d s
- Page 78 and 79: WATER-COOLED ICE MACHINES1. Perform
- Page 80 and 81: HARVEST SEQUENCE5. HarvestThe water
- Page 82 and 83: ICE MAKINGSEQUENCE OFOPERATIONHarve
- Page 84 and 85: HARVEST SEQUENCE4. Harvest CycleThe
- Page 86 and 87: SM50INITIAL START-UP OR START-UP AF
- Page 88 and 89: ENERGIZED PARTS CHARTSM50Self-conta
- Page 90 and 91: Water Level CheckThe float valve is
- Page 92 and 93: QM20/QM30Routine adjustments and ma
- Page 94 and 95: 5. Remove the two screws holding th
- Page 96 and 97: Clean (Green)Pressing the “Clean
- Page 98 and 99: This Page Intentionally Left Blank9
- Page 100 and 101: DIAGNOSING ICE THICKNESS CONTROLCIR
- Page 102 and 103: Ice Machine Cycles Into Harvest Bef
- Page 104 and 105: INSTALLATION AND VISUAL INSPECTIONC
Step 7 Mix a solution of cleaner and warm water.Depending on the amount of mineral buildup, a largerquantity of solution may be required. Use the ratio inthe table below to mix enough solution to thoroughlyclean all parts.SolutionWaterMixed withTypeCleaner 1 gal. (4 l) 16 oz (500 ml) cleanerStep 8 Use ½ of the cleaner/water solution to cleanall components. The cleaner solution will foam when itcontacts lime scale and mineral deposits; once thefoaming stops use a soft bristle brush, sponge or cloth(not a wire brush) to carefully clean the parts. Soak theparts for 5 minutes (15 – 20 minutes for heavily scaledparts). Rinse all components with clean water.Step 9 While components are soaking, use ½ of thecleaner/water solution to clean all foodzone surfacesof the ice machine and bin. Use a nylon brush or clothto thoroughly clean the following ice machine areas:• Evaporator plastic parts – including top, bottomand sides• Bin bottom, sides and topRinse all areas thoroughly with clean water.Step 10 Mix a solution of sanitizer and warm water.SolutionTypeWaterMixed WithSanitizer 6 gal. (23 l) 4 oz (120 ml) sanitizerStep 11 Use 1/2 of the sanitizer/water solution tosanitize all removed components. Use a cloth orsponge to liberally apply the solution to all surfaces ofthe removed parts or soak the removed parts in thesanitizer/water solution. Do not rinse parts aftersanitizing.Part Number 80-01111-9 7/10 57