Manitowoc
Manitowoc Manitowoc
SM50/QM20/QM30After moving the ice machine into the installationlocation, it must be leveled for proper operation.Follow these steps to level the ice machine:1. Use a level to check the levelness of the icemachine from front to back and from side to side.2. If the ice machine is not level, adjust the levelingglides or legs on each corner of the base of theice machine as necessary.3. Check the levelness of the ice machine after eachadjustment.4. Repeat steps 2 and 3 until the ice machine is levelfrom front to back and from side to side.LevelersSV1705SV1679BLegsSV160626 Part Number 80-01111-9 7/10
Electrical RequirementsVOLTAGEThe maximum allowable voltage variation is ±10% ofthe rated voltage on the ice machine model/serialnumber plate at start-up (when the electrical load ishighest).The 115/1/60 ice machines are factory pre-wired witha 6' (1.8 m) power cord, and NEMA 5-15P-plugconfiguration.The 208-230/1/60 and 230/1/50 ice machines arefactory pre-wired with a power cord only, no plug issupplied.FUSE/CIRCUIT BREAKERA separate fuse/circuit breaker must be provided foreach ice machine. Circuit breakers must be H.A.C.R.rated (does not apply in Canada).TOTAL CIRCUIT AMPACITYThe total circuit ampacity is used to help select thewire size of the electrical supply.The wire size (or gauge) is also dependent uponlocation, materials used, length of run, etc., so it mustbe determined by a qualified electrician.Part Number 80-01111-9 7/10 27
- Page 1: ManitowocQM20/QM30/QM45SM50Q130/Q17
- Page 4 and 5: Read These Before Proceeding:! Caut
- Page 6 and 7: Cleaning the Condenser . . . . . .
- Page 8 and 9: Freeze Cycle Is Long, Low Ice Produ
- Page 10 and 11: CHARTSCycle Times, 24 Hr. Ice Produ
- Page 12 and 13: How to Read a Model NumberCube Size
- Page 14 and 15: Model/Serial Number LocationThe mod
- Page 16 and 17: SM50MODEL/SERIALNUMBER PLATE16 Part
- Page 18 and 19: LaborQ130/Q170/Q210/Q2701. Labor re
- Page 20 and 21: RESIDENTIAL WARRANTY COVERAGEWhat D
- Page 22 and 23: How State Law AppliesThis limited w
- Page 24 and 25: Ice Machine Clearance RequirementsS
- Page 28 and 29: Electrical SpecificationsQ130/Q170/
- Page 30 and 31: QM20/QM30/QM45 Air-cooled Ice Machi
- Page 32 and 33: COOLING TOWER APPLICATIONSWater Coo
- Page 34 and 35: QM20/QM30LocationIce MakingWater In
- Page 36 and 37: This Page Intentionally Left Blank3
- Page 38 and 39: ON/OFF/WASHTOGGLESWITCHCONDENSER AI
- Page 40 and 41: ON/OFF/WASHTOGGLESWITCHQM20 Ice Mac
- Page 42 and 43: WATERPUMPEVAPORATORWATERSHUTTERASSE
- Page 44 and 45: AIR-COOLED CONDENSERA dirty condens
- Page 46 and 47: Step 1 Set the toggle switch to the
- Page 48 and 49: D. Remove the Ice Thickness Probe
- Page 50 and 51: Disassembly• Twist both of the in
- Page 52 and 53: F. Remove the Float Valve• Turn t
- Page 54 and 55: H. Remove the ice damper.Q130• Gr
- Page 56 and 57: I. Remove the Bin Door• Grasp the
- Page 58 and 59: Step 12 Use 1/2 of the sanitizer/wa
- Page 60 and 61: QM20/QM30CLEANING AND SANITIZING PR
- Page 62 and 63: Step 6 Remove parts for cleaning.A.
- Page 64 and 65: Step 7 Mix a solution of cleaner an
- Page 66 and 67: Step 20 Use half of the sanitizer/w
- Page 68 and 69: 4. Wait until the Clean light flash
- Page 70 and 71: WATER SHUTTERSThe water shutter is
- Page 72 and 73: SUMP DRAIN OVERFLOW TUBE1. Remove c
- Page 74 and 75: SPRAY BAR, WATER PUMP AND HOSE! War
Electrical RequirementsVOLTAGEThe maximum allowable voltage variation is ±10% ofthe rated voltage on the ice machine model/serialnumber plate at start-up (when the electrical load ishighest).The 115/1/60 ice machines are factory pre-wired witha 6' (1.8 m) power cord, and NEMA 5-15P-plugconfiguration.The 208-230/1/60 and 230/1/50 ice machines arefactory pre-wired with a power cord only, no plug issupplied.FUSE/CIRCUIT BREAKERA separate fuse/circuit breaker must be provided foreach ice machine. Circuit breakers must be H.A.C.R.rated (does not apply in Canada).TOTAL CIRCUIT AMPACITYThe total circuit ampacity is used to help select thewire size of the electrical supply.The wire size (or gauge) is also dependent uponlocation, materials used, length of run, etc., so it mustbe determined by a qualified electrician.Part Number 80-01111-9 7/10 27
Change language