Manitowoc
Manitowoc Manitowoc
How State Law AppliesThis limited warranty gives you specific legal rights,and you may also have rights that vary from state tostate or from one jurisdiction to another.Registration CardTo secure prompt and continuing warranty service, thiswarranty registration card must be completed and sentto Manitowoc within thirty (30) days from the sale date.Complete the following registration card and send it toManitowoc at the address shown above. Retain a copyfor your records.HOW TO OBTAIN WARRANTY SERVICETo obtain warranty service or information regardingyour Product, please contact us at:MANITOWOC ICE2110 S. 26 th St.,P.O. Box 1720Manitowoc, WI 54221-1720Telephone: 920-682-0161 Fax: 920-683-7585www.manitowocice.com22 Part Number 80-01111-9 7/10
InstallationLocation of Ice MachineThe location selected for the ice machine must meetthe following criteria. If any of these criteria are notmet, select another location.• The location must be indoors.• The location must be free of airborne and othercontaminants.• Air temperature:• Q130/Q170/Q210/Q270/QM45 must be atleast 40°F (4°C) but must not exceed 110°F(43.4°C).• QM20/QM30 must be at least 50°F (10°C) butmust not exceed 113°F (45°C).• SM50 must be at least 50°F (10°C) but mustnot exceed 110°F (43°C).• The location must not be near heat-generatingequipment or in direct sunlight.• The location must be capable of supporting theweight of the ice machine and a full bin of ice.• The location must allow enough clearance forwater, drain, and electrical connections in the rearof the ice machine.• The location must not obstruct airflow through oraround the ice machine (condenser airflow is inand out the front). Refer to the chart below forclearance requirements.• The ice machine must be protected if it will besubjected to temperatures below 32°F (0°C).Failure caused by exposure to freezingtemperatures is not covered by the warranty.Part Number 80-01111-9 7/10 23
- Page 1: ManitowocQM20/QM30/QM45SM50Q130/Q17
- Page 4 and 5: Read These Before Proceeding:! Caut
- Page 6 and 7: Cleaning the Condenser . . . . . .
- Page 8 and 9: Freeze Cycle Is Long, Low Ice Produ
- Page 10 and 11: CHARTSCycle Times, 24 Hr. Ice Produ
- Page 12 and 13: How to Read a Model NumberCube Size
- Page 14 and 15: Model/Serial Number LocationThe mod
- Page 16 and 17: SM50MODEL/SERIALNUMBER PLATE16 Part
- Page 18 and 19: LaborQ130/Q170/Q210/Q2701. Labor re
- Page 20 and 21: RESIDENTIAL WARRANTY COVERAGEWhat D
- Page 24 and 25: Ice Machine Clearance RequirementsS
- Page 26 and 27: SM50/QM20/QM30After moving the ice
- Page 28 and 29: Electrical SpecificationsQ130/Q170/
- Page 30 and 31: QM20/QM30/QM45 Air-cooled Ice Machi
- Page 32 and 33: COOLING TOWER APPLICATIONSWater Coo
- Page 34 and 35: QM20/QM30LocationIce MakingWater In
- Page 36 and 37: This Page Intentionally Left Blank3
- Page 38 and 39: ON/OFF/WASHTOGGLESWITCHCONDENSER AI
- Page 40 and 41: ON/OFF/WASHTOGGLESWITCHQM20 Ice Mac
- Page 42 and 43: WATERPUMPEVAPORATORWATERSHUTTERASSE
- Page 44 and 45: AIR-COOLED CONDENSERA dirty condens
- Page 46 and 47: Step 1 Set the toggle switch to the
- Page 48 and 49: D. Remove the Ice Thickness Probe
- Page 50 and 51: Disassembly• Twist both of the in
- Page 52 and 53: F. Remove the Float Valve• Turn t
- Page 54 and 55: H. Remove the ice damper.Q130• Gr
- Page 56 and 57: I. Remove the Bin Door• Grasp the
- Page 58 and 59: Step 12 Use 1/2 of the sanitizer/wa
- Page 60 and 61: QM20/QM30CLEANING AND SANITIZING PR
- Page 62 and 63: Step 6 Remove parts for cleaning.A.
- Page 64 and 65: Step 7 Mix a solution of cleaner an
- Page 66 and 67: Step 20 Use half of the sanitizer/w
- Page 68 and 69: 4. Wait until the Clean light flash
- Page 70 and 71: WATER SHUTTERSThe water shutter is
InstallationLocation of Ice MachineThe location selected for the ice machine must meetthe following criteria. If any of these criteria are notmet, select another location.• The location must be indoors.• The location must be free of airborne and othercontaminants.• Air temperature:• Q130/Q170/Q210/Q270/QM45 must be atleast 40°F (4°C) but must not exceed 110°F(43.4°C).• QM20/QM30 must be at least 50°F (10°C) butmust not exceed 113°F (45°C).• SM50 must be at least 50°F (10°C) but mustnot exceed 110°F (43°C).• The location must not be near heat-generatingequipment or in direct sunlight.• The location must be capable of supporting theweight of the ice machine and a full bin of ice.• The location must allow enough clearance forwater, drain, and electrical connections in the rearof the ice machine.• The location must not obstruct airflow through oraround the ice machine (condenser airflow is inand out the front). Refer to the chart below forclearance requirements.• The ice machine must be protected if it will besubjected to temperatures below 32°F (0°C).Failure caused by exposure to freezingtemperatures is not covered by the warranty.Part Number 80-01111-9 7/10 23
Change language