AMITY (VENT-FREE) NATURAL GAS STOVE HEATER - Desa
AMITY (VENT-FREE) NATURAL GAS STOVE HEATER - Desa AMITY (VENT-FREE) NATURAL GAS STOVE HEATER - Desa
OPERATINGHEATERContinuedTO TURN OFF GAS TO APPLIANCEShutting Off Heater1. Press in and turn control knob clockwise Clockwise to the HIGH position.2. Turn the control knob clockwise Clockwise to the PILOT position.3. Press in control knob and turn clockwise Clockwise to the OFF Position.Shutting Off Burners Only (pilot stays lit)1. Turn the control knob clockwise Clockwise to the HIGH position.2. Press in and turn control knob clockwise Clockwise to the PILOT position.MANUAL LIGHTING PROCEDURE1. Follow steps 1 through 5 under Lighting Instructions, pages 18 and 19.2. Pilot is located inside stove cavity attached to burner. Lift off top grate to allowaccess to pilot.3. Depress control knob and light pilot with match.4. Keep control knob pressed in for 30 seconds after lighting pilot. After 30seconds, release control knob.5. Place top grate back into position. Now follow step 8, page 19.INSPECTINGBURNERSCheck pilot flame pattern and burner flame patterns often.PILOT FLAME PATTERNFigure 23 shows a correct pilot flame pattern. Figure 24 shows an incorrect pilot flamepattern. The incorrect pilot flame is not touching the thermocouple. This will cause thethermocouple to cool. When the thermocouple cools, the heater will shut down.Thermocouple Pilot Burner Pilot BurnerThermocoupleFigure 23 - Correct PilotFlame PatternFigure 24 - Incorrect PilotFlame PatternIf pilot flame pattern is incorrect, as shown in Figure 24• turn heater off (see To Turn Off Gas to Appliance, above)• see Troubleshooting, pages 21 through 2420104024
CLEANINGANDMAINTENANCEWARNING ICON G 001WARNINGTurn off heater and let cool before cleaning.WARNING ICON G 001CAUTIONYou must keep control areas, burner, and circulating air passagewaysof heater clean. Inspect these areas of heater before eachuse. Have heater inspected yearly by a qualified service person.Heater may need more frequent cleaning due to excessive lint fromcarpeting, bedding material, etc.ODS/PILOT AND BURNER• Use a vacuum cleaner or small, soft bristled brush to clean.LOGS• Replace log(s) if broken or chipped (dime-sized or larger).TROUBLE-SHOOTINGNote: All troubleshootingitems are listed in order ofoperation.WARNING ICON G 001WARNINGTurn off heater and let cool before servicing. Only a qualifiedservice person should service and repair heater.WARNING ICON G 001CAUTIONNever use a wire, needle, or similar object to clean ODS/pilot. Thiscan damage ODS/pilot unit.OBSERVEDPROBLEMWhen ignitor buttonis pressed, there is nospark at ODS/pilotPOSSIBLECAUSE1. Ignitor electrode not connectedto ignitor cable2. Ignitor cable pinched orwet3. Piezo ignitor nut is loose4. Broken ignitor cable5. Bad piezo ignitor6. Ignitor electrode positionedwrong7. Ignitor electrode brokenREMEDY1. Reconnect ignitor cable2. Free ignitor cable ifpinched by any metal ortubing. Keep ignitorcable dry3. Tighten nut holdingpiezo ignitor to basepanel of log set. Nut islocated behind basepanel.4. Replace ignitor cable5. Replace piezo ignitor6. Replace ignitor7. Replace ignitor104024Continued21
- Page 5 and 6: 104024AIR FORCOMBUSTIONANDVENTILATI
- Page 7 and 8: AIR FORCOMBUSTIONANDVENTILATIONCont
- Page 9 and 10: INSTALLINGContinuedFront ViewCeilin
- Page 11 and 12: INSTALLINGContinued8. Fasten each l
- Page 13 and 14: INSTALLINGContinuedINSTALLING GAS L
- Page 15 and 16: INSTALLINGContinued* An A.G.A. desi
- Page 17 and 18: INSTALLINGContinuedTest Pressures E
- Page 19: OPERATINGHEATERContinued4. Wait fiv
- Page 23 and 24: TROUBLE-SHOOTINGContinuedOBSERVEDPR
- Page 25 and 26: 104024TECHNICALSERVICESPECIFICATION
- Page 27 and 28: PARTS LISTSVYD18NThis list contains
- Page 29 and 30: PARTS LISTSCIVFC, SCIVFB,SCIVFG, SC
- Page 31 and 32: NOTES______________________________
OPERATING<strong>HEATER</strong>ContinuedTO TURN OFF <strong>GAS</strong> TO APPLIANCEShutting Off Heater1. Press in and turn control knob clockwise Clockwise to the HIGH position.2. Turn the control knob clockwise Clockwise to the PILOT position.3. Press in control knob and turn clockwise Clockwise to the OFF Position.Shutting Off Burners Only (pilot stays lit)1. Turn the control knob clockwise Clockwise to the HIGH position.2. Press in and turn control knob clockwise Clockwise to the PILOT position.MANUAL LIGHTING PROCEDURE1. Follow steps 1 through 5 under Lighting Instructions, pages 18 and 19.2. Pilot is located inside stove cavity attached to burner. Lift off top grate to allowaccess to pilot.3. Depress control knob and light pilot with match.4. Keep control knob pressed in for 30 seconds after lighting pilot. After 30seconds, release control knob.5. Place top grate back into position. Now follow step 8, page 19.INSPECTINGBURNERSCheck pilot flame pattern and burner flame patterns often.PILOT FLAME PATTERNFigure 23 shows a correct pilot flame pattern. Figure 24 shows an incorrect pilot flamepattern. The incorrect pilot flame is not touching the thermocouple. This will cause thethermocouple to cool. When the thermocouple cools, the heater will shut down.Thermocouple Pilot Burner Pilot BurnerThermocoupleFigure 23 - Correct PilotFlame PatternFigure 24 - Incorrect PilotFlame PatternIf pilot flame pattern is incorrect, as shown in Figure 24• turn heater off (see To Turn Off Gas to Appliance, above)• see Troubleshooting, pages 21 through 2420104024
Change language