to download - Electric Motor Service

FORD PMGR (cont'd.)WAI No. Description62-2402-2 BUSHING - D.E., C.E. (2X-Undersize,11.91mm ID x 15.13mm OD x 10.2mm L)62-2402-3 BUSHING - D.E., C.E. (3X-Undersize,11.79mm ID x 15.13mm OD x 10.2mm L)62-2403 BUSHING - D.E., Replaces Needle Brg.(12.00mm ID x 16.04mm OD x 10.2mm L)62-2403-1 BUSHING - D.E. (1X-Undersize,11.94mm ID x 16.04mm OD x 10.2mm L)62-2403-2 BUSHING - D.E. (2X-Undersize,11.86mm ID x 16.04mm OD x 10.2mm L)62-2500 BUSHING - Reduction Gear, PMOSGR Strs.(14.33mm ID x 17.26mm OD x 12.5mm L)62-2700 BUSHING - Stationary Gear(19.06mm ID x 22.28mm OD x 6.04mm L)66-205-2 SOLENOID (Spade S-Term., LH, Zinc-Yellow Case)66-207-2 SOLENOID (M6 x 1.0 S-Term., RH)66-208-2 SOLENOID (M6 x 1.0 S-Term., LH)66-209-2 SOLENOID (M6 x 1.0 S-Term., LH, w/ Plunger Boot)66-2201 SOLENOID CAP ASSY. (Spade S-Term., LH,w/ Suppression Diode)66-2202 SOLENOID REPAIR KIT (w/ 66-2201 Cap Assy.)66-2203 SOLENOID CAP ASSY. (M6 x 1.0 S-Term., RH)66-2204 SOLENOID CAP ASSY. (M6 x 1.0 S-Term., LH)66-2401 GASKET - Solenoid Cap66-2402 GASKET - Solenoid Mtg.66-2755 MOVABLE CONTACT - Solenoid66-2757 INSULATOR - Solenoid Movable Contact68-217 BRUSH - Field, Early Style Strs. w/ Spade S-Term.68-217-3 BRUSH - Field, Early Style Strs. w/ Spade S-Term.68-218 BRUSH - Field (wo/ Grommet & Terminal)68-218-3 BRUSH - Field (wo/ Grommet & Terminal)68-219 BRUSH - Grd.68-219-1 BRUSH - Grd.68-219-3 BRUSH - Grd.68-220 BRUSH - Field, Late Style Strs. w/ M6 x 1.0 S-Term.68-220-1 BRUSH - Field, Late Style Strs. w/ M6 x 1.0 S-Term.68-220-3 BRUSH - Field, Late Style Strs. w/ M6 x 1.0 S-Term.69-201 BRUSH HOLDER ASSY.69-201-2 BRUSH HOLDER ASSY.69-2206 BRUSH HOLDER69-2206-1 BRUSH HOLDER69-2704 BRUSH SPRING71-2103 SEAL - 51-249 D.E. Hsg.71-2309 PLUG - Shift Lever Support (incl. Pivot Pad)71-2310 DRAIN TUBE - 51-249 D.E. Hsg.71-2313 DRAIN TUBE - 51-249 D.E. Hsg.71-2317 DRAIN TUBE - 51-259 D.E. Hsg.72-2115 INSULATOR - Brush Holder (For 69-201 Brush Holder Assy.)76-2114 COVER - Solenoid Terms.76-2302 COVER - Planetary Shaft Assy.76-2562 STATIONARY CONTACT - Soln. Batt., Motor Terms.(M8 x 1.25 x 22mm L)76-2602 TERMINAL LEAD - Motor(for units w/ threaded post S-Term.)76-2603 REPAIR LEAD - Solenoid S-Terminal76-2800 STOP RING - Str. DriveWAI No. Description76-2801 STOP COLLAR76-2801-1 STOP COLLAR (Stamped & Heat Treated)76-2801-2 STOP COLLAR (Machined & Heat Treated)76-2808 RETAINER - Planetary Shaft (1st prod.w/ 16mm Dia. Ring Groove)76-2809 PLANETARY SHAFT - 1st Prod. (18mm Cavity,w/ 10mm L Bushing)76-2810 PLANETARY GEAR (13-Teeth, 19mm Gear OD,w/ 62-2200 Bushing)76-2811 STATIONARY GEAR (37-Teeth)76-2812 BALL - Shaft Assy. (.250 Dia. Std. Size)76-2814 RETAINER - Magnet76-2816 PLANETARY GEAR (13-Teeth, 19mm Gear OD,w/ 8-203 Bearing)76-2818 LOCATING DOWEL PIN - Converts 51-239 to replace51-238 D.E. Hsg. w/ Locating Dowel. (M10 x 1.5 Dowel)76-2819 RETAINER - Reduction Gear, Planetary Shaft (2nd prod.w/ 17mm Dia. Ring Groove)76-2820 SHAFT - Reduction Gear, PMOSGR Strs.76-2822 PLANETARY SHAFT - 2nd Prod. (16mm Cavity,w/ 10mm L Bushing)76-2825 BALL - Shaft Assy. (.297 Dia Oversize)76-2826 BALL - Shaft Assy. (.234 Dia. Undersize)76-2827 REDUCTION GEAR - PMOSGR Strs (22-T,51.7mm Gear OD, 41.8mm Collar OD)76-7553 TERMINAL - Used to convert S-Term from post tomale spade (90° male spade w/ hole to fit 6mm post)79-2114 STARTER HARNESS KIT - For replacing Early Field CoilStrs. w/ PMGR (Spade S-Term.)79-2114-1 STARTER HARNESS KIT - For replacing Early Field CoilStrs. w/ PMGR (Threaded Post S-Term.)79-2503 TERMINAL KIT - Soln. S-Term.79-2825 BALL KIT - Shaft Assy. (.297 Dia. Oversize, w/ Gauge)79-2826 BALL KIT - Shaft Assy. (.234 Dia. Undersize, w/ Gauge)84-4102 FLAT WASHER - Solenoid Movable Contact (5/32 ID)84-4402 LOCK WASHER - Soln. Batt., Motor Terms. (5/16 ID, Split)84-4712 FLAT WASHER - Planetary Shaft (3/4 ID)84-5910 LOCATING DOWEL PIN - D.E. (3/8 Dia. x 1 L)84-5914 SPLIT ROLL PIN - Reduction Gear Shaft, PMOSGR Strs.(5/32 Dia. x 7/8 L)85-1317 THRU BOLT (M5 x 0.8 x 126mm L)85-1318 THRU BOLT (M5 x 0.8 x 125mm Lw/ M5 x 0.8 x 13mm L Ext.)85-1319 SCREW - Soln. Mtg. (M6 x 1.0 x 36mm L, T25 Torx)85-1320-1 SCREW - Brush Holder Assy. (M5 x 0.8 x 10mm L, Hex)85-1344 THRU BOLT (M5 x 0.8 x 125mm Lw/ M6 x 1.0 x 13mm L Ext.)85-2301 HEX NUT - Solenoid Switch Term.(M6 x 1.0 x 10mm F x 5mm T, w/ Att. Washer)85-2401 HEX NUT - Soln. Batt., Motor Terms.(M8 x 1.25 x 13mm F x 5mm T)85-2404 HEX NUT - Soln. Battery, Motor Terms.(M8 x 1.25 x 13mm F x 3.2mm T)85-9401 LOCK WASHER - Soln. Batt., Motor Terms. (8mm ID,Conical)88-734 GAUGE - Determines Ball Size for Armature & ShaftFORD PMGR95