Tsubaki Guide to Forestry Products

More documents

Recommendations

Info

CROSS CUT SLASHERDEBARKER INFEEDCONVEYOR/DEBARKERWhen strength really mattersSplitSprocketChallenge – Debarker Infeed conveyorStart/stop operation is required by the operator. This places demanding and varying loads on the drive chain.LambdaChainSolutionDrive chain: HT chain provides up to 30% greaterultimate tensile strength over standard roller chain.Mill chainSprockets: Forward/backward operation can resultin keyway backlash. The use of Powerlock sprocketseliminates the need for a keyway.Typical size range for this applicationRS80HT to RS160HT single and multi strand.WD(H)104, 110, 120. WH124(XHD) with C cradleattachment.Challenge – DebarkerFor ring debarkers there is shock load from crooked logs. Also high speed operation limits the effectiveness of lubricationdue to centrifugal force. Knife jam-up can require forward / backward operation. For drum debarkers, general operationoverload and/or high impact.ChallengeSolutionTypical size range for this applicationSolutionDrive chain: Lambda chain offersmaintenance-free operation.Mill chainSprockets: Remote access and the need for quickchangeout can be solved by split design sprockets.Remote access.Typical size range for this applicationRSD100Lambda to RSD140LambdaWR124(XHD), WR132(XHD)Drive chain: SpeedMaster designed for speeds greater than 400feet per minute. Special material, surface treatment and conn link.HT chain for higher tensile strength to resist shock load.Drag chainSprockets: Forward/backward operation can resultin keyway backlash. The use of Powerlock sprockets eliminatesthe need for a keyway.For ring debarker RS80SM or HT to RS160SM or HT single andmulti strand. For drum debarker Super 120 to Super 160-3.WD(RS)480(XHD), also sizes 104, 110, 120 and 132.With or without wing attachments.94 95
LOG DECK BIN AND INFEEDMAINSAW LINEApplication: Canter in/out feeds Savings: $29,400.00Tsubaki solution: Previous chain brand suffered cracked sideplatesand severe elongation after 6 months. Tsubakifeatures and quality lasted 30 months.It really mattered to this Tsubaki customerCOST SAVINGS!SplitSprocketChallengeDrive: High speeds can limit the effectiveness of lubrication due to centrifugal force.Sharp top conveyor: Tips can wear prematurely compared to normal wear of the load bearing chain components.SolutionDrive chain: Lambda chain offersmaintenance-free operation.ChallengeAccess to the drive can be confi ned.LambdaChainTypical size range for this applicationRSD100Lambda to RSD140LambdaSolutionDrive chain: SpeedMaster designed for speeds greaterthan 400 feet per minute. Special material, surfacetreatment and conn link.Sharp top conveyor: NEW Tsubaki spec sharp top chainincreases tip area hardness by 20%.This increases overall chain life.Drag chainSprockets: Premium Tsubaki sprockets with high carbon 1030or 1045 material allow for a consistent hardened tooth that is anecessity for the demands of this application.Sharp Top ChainRF32BTypical size range for this applicationRS80SM to RS100SMRF32B SharptopWD(H)(RS)110, 480(XHD).Can be suppliedwith wing attachments.Mill chainLog deck infeed: WHC 124 , 132 (IBR)Log deck: H78B camelback, WH 78 ,82. WDH110, 111.WH(C) 124, 132. WH124XHD. CC5riv.Sprockets: Remote access and the need for quick changeoutcan be solved by split design sprockets.SpeedMasterChain96 97
Page 1: Tsubaki of Canada Limited1630 Drew
Page 6 and 7: SPEEDMASTER DRIVE CHAINApplication:
Page 8 and 9: TrCURVED LAMBDASELF-LUBRICATING DRI
Page 10 and 11: HT SERIES CHAINSUPER-HSERIES CHAINW
Page 12 and 13: SHARP TOP CHAINWhen grip really mat
Page 14 and 15: INTRODUCTION TOCONVEYOR CHAIN & ATT
Page 16 and 17: STANDARD ATTACHMENT CHAINWhen exped
Page 18 and 19: STANDARD ATTACHMENT CHAINORDERING A
Page 20 and 21: INTRODUCTION TOMILL & DRAG CHAINApp
Page 22: 1630 Drew Road, Mississauga, ON L5S
Page 26 and 27: SPROCKETSWhen quality really matter
Page 28 and 29: NO. 80 “QD” STYLE 1" PITCHNO. 8
Page 30 and 31: NO. 100 FINISHED BORE 1 1/4" PITCHN
Page 32 and 33: NO. 100 DOUBLE SPLITTAPER 1 1/4" PI
Page 34 and 35: NO. 140 “QD” STYLE 1 3/4" PITCH
Page 36 and 37: MILL CHAIN SPROCKETSWhen toughness
Page 42 and 43: SPLIT TAPER BUSHINGSWhen compatibil
Page 44 and 45: “XT” STYLE BUSHINGS“XT” STY
Page 46 and 47: SHOCK RELAYSWhen control really mat
Page 48 and 49: When innovation really mattersDrive
Page 52 and 53: EDGERApplication: Bull Edger DriveS
Page 54 and 55: DROPSORTERApplication: Drop Sorter
Page 56 and 57: OTHER SIGNIFICANTFORESTRY APPLICATI

Tsubaki Guide to Forestry Products

Create successful ePaper yourself

Delete template?

Save as template?