R&S®SFU Broadcast Test System Specifications

R&S®SFUBroadcast Test SystemSpecificationsTest & MeasurementData Sheet | 07.00

2 R&S ® SFU Broadcast Test System Version 07.00, October 2008

Key featuresGeneral• Analog TV, digital TV and audio broadcast multistandard test platform• Output frequency from 100 kHz to 3 GHz• Generation of internal noise and interferer signals• Fully digital baseband signal processing• Upgradeability to multifunctional broadcast test system• Easy installation of most options at customer siteIntuitive, fast and easy operation• Color display with 1024 × 768 pixels (XVGA format)• Intuitive user interface with Windows XP Embedded• Context-sensitive help system• User-definable favorites for fast accessOutstanding signal quality• I/Q modulator with 180 MHz RF bandwidth• Very low SSB phase noise of typ. –135 dBc at 1 GHz (20 kHz carrier offset, 1 Hz measurement bandwidth)• High optional output power of up to +19 dBm (PEP), overrange +26 dBm• High-stability reference oscillator as standardUnrivaled flexibility for research and development• Multistandard platform that supports expansions• Transmission simulations• TS baseband generator and recorder with universal coder for realtime signal generation• TRP baseband player for realtime signal generation• Video generator for realtime signal generation• Arbitrary waveform generator with 64 Msample, supported by R&S ® WinIQSIM software• Internal hard disk as standard for storing waveforms and modulation data• Wear-free electronic attenuator of up to 3 GHz• Minimum space requirements: signal generator and test transmitter accommodated in one instrument of only four height unitsEasy remote access• Remote control via GPIB and LAN• User-friendly remote access by VNC or Remote Desktop• USB connectors for keyboard, mouse, and external storage media6 R&S ® SFU Broadcast Test System Version 07.00, October 2008

SpecificationsSpecifications apply under the following conditions: 30 minutes warm-up time at ambient temperature, specified environmentalconditions met, calibration cycle adhered to, and all internal automatic adjustments performed."Typical values" are designated with the abbreviation "typ." These values are verified during the final test but are not assured byRohde & Schwarz."Nominal values" are design parameters that are not assured by Rohde & Schwarz.These values are verified during product development but are not specifically tested during production.RF characteristicsFrequencyRangeAccuracyResolution of settingResolution of synthesisFrequency sweepDigital sweep in discrete steps300 kHz to 3 GHzunderrange100 kHz to

LevelRF outputMaximum levelSetting rangeLevel accuracyAdditional uncertainty with ALC OFF,S&H (sample & hold)Output impedanceVSWR in 50 systemUninterrupted level settingBack-feed (from 50 source)connectorN female, frontoutput impedance50 overvoltage protection35 Vwithout option +13 dBm (PEP) 1with R&S ® SFU-B90 option (high power) +19 dBm (PEP)without option–120 dBm to +20 dBmwith R&S ® SFU-B90 option (high power) –120 dBm to +30 dBmresolution0.01 dB"auto" attenuator mode,temperature range +18 °C to +33 °Cf 3 GHz / level 100 dBm

Spectral purityHarmonicslevel 8 dBm, CW

I/Q modulationI/Q modulatorOperating modesexternal wideband I/Qinternal baseband I/QModulation frequency range I/Q wideband 100 MHzI/Q modulation inputsconnectorBNC female, frontinput impedance50 VSWR up to 30 MHz

External wideband I/QI/Q inputs (I/Q EXT)connectorBNC female, front(connector equal to I/Q analog IN) input impedance50 VSWR up to 50 MHz

Extended I/Q (R&S ® SFU-K80 option)The R&S ® SFU-K80 option allows external analog and digital signals to be fed into the baseband signal processing of the R&S ® SFU.Input signals can be faded in and noise signals superimposed if the fading simulator and noise options have been installed. In addition,the digital baseband signals are available externally.Analog I/Q INI/Q analog inputs (I/Q EXT)(connector equal to I/Q wideband IN)Digital I/Q INI/Q digital inputI/Q digital modulation inputsDigital I/Q OUTI/Q digital outputI/Q digital modulation outputsconnectorBNC female, frontinput impedance50 VSWR (up to 25 MHz)

Digital basebandInternal test signalsMPEG-2 TS packetheader + 184 byte payload00 (hex), FF (hex), PRBS (selectable)PIDNULL (1FFF hex)/variableMPEG-specific TS packet sync byte + 187 byte payload 00 (hex), FF (hex), PRBS (selectable)DIRECTV TS packet header + 127 byte payload PRBS (DIRECTV only)DIRECTV-specific TS packet 130 byte payload PRBS (DIRECTV only)PRBS PRBS in line with ITU-T O.151 2 23 –1/2 15 –1 (selectable)MPEG-2 inputsParallel SPI inputconnectorD-Sub female, 25 pins, front and rearinput levelLVDSinput impedance100 , differentialASI/SMPTE 310 serial inputconnectorBNC female, front and rearASI input level200 mV to 880 mVSMPTE 310 input level400 mV to 880 mVinput impedance75 ASI data rate270 Mbit/sSMPTE 310 data rate19.392658 Mbit/sStuffingASI, SMPTE 310, SPION/OFFstuffing packetssee MPEG-2 TS packet at “Internal testsignals”TS EXT CLKconnectorBNC female, rearinput levelTTL, sinewave (0 dBm)input impedance50 Indication measured values packet length, data rate, useful data rateETI input/output (R&S ® SFU-B11 option)The R&S ® SFU-B11 option allows external ETI data streams to be fed into the baseband signal processing of the R&S ® SFU.T-DMB/DAB signals can be faded in and noise signals superimposed if the fading simulator and noise options have been installed.ETI input/outputin line with ETI NI, ETI NA5592,ETI NA5376Serial ETI inputconnectorBNC female, rearETI input level0 V to ±2.37 V (ITU T G.703/G.704)input impedance75 ETI data rate2048 kbit/scodingHDB3Serial ETI output 5 connectorBNC female, rearETI output level0 V to ±2.37 V (ITU-T G.703/G.704)output impedance75 ETI data rate2048 kbit/scoding HDB35 Requires Coder 2110.3306 with C.I. >4.xx and R&S ® SFU-B11 model .03 (2110.3887).Version 07.00, October 2008 R&S ® SFU Broadcast Test System 13

TS generator (R&S ® SFU-K20 option)Serial TS outputmodeconnectoroutput impedanceASIoutput leveldata ratemodeSMPTE 310Moutput leveldata rateTransport streamfilesfile formatlength of transport stream packetssequence lengthdata ratenet data ratedata volumePCR jittershapefrequencyamplitudeSignal setASI, SMPTE 310M (selectable)BNC female, rear75 800 mV270 Mbit/spacket or continuous800 mV19.392658 Mbit/sRohde & Schwarz data streamsgenerated transport streams (GTS) formatATSC: 188/208 bytes (selectable)DVB: 188/204 bytes (selectable)generation of endless and seamlesstransport streams with repetition of video,audio, and data contents100 kbit/s to 214 Mbit/s (including nullpackets)max. 90 Mbit/smax. 80 Mbyte payloadsinewave, rectangle, triangle1 MHz to 100 kHz0 ms to 1 ms, in increments of 0.1 μsmoving picture sequences and testpatterns with test tones, for 625 and 525lines; DVB/ATSC systems, additionalsignals via optionsTS recorder (R&S ® SFU-K21 option) (see ordering information)The TS recorder can be used for recording ETI data streams if the ETI input/output (R&S ® SFU-B11 option) is installed.Parallel inputSerial TS inputmodeconnectorinput impedanceinput levelinput clockmodeconnectorinput impedanceASIinput leveldata ratemodeSMPTE 310Minput leveldata rateSPID-Sub female, 25 pins, front and rear100 , differentialLVDS84.375 kHz to 7.5 MHz (60 Mbit/s NTFS)84.375 kHz to 11.25 MHz (90 Mbit/s CFS)ASI, SMPTE 310M, ETI (selectable)BNC female, front and rear75 200 mV to 880 mV270 Mbit/spacket or continuous400 mV to 880 mV19.392658 Mbit/s14 R&S ® SFU Broadcast Test System Version 07.00, October 2008

RecordingReplaySerial TS outputSerial ETI input/outputmodeTRPT10BINdata ratedata volumerecording timerecording via ASI, SPI, SMPTE 310M, orETI; check of transport stream structureand packet size (188/204/208);SPI 8-bit interface: recording of data as afunction of DVALID signalrecording via SPI or ETI; check oftransport stream structure and packet size(188/204/208); recording of 8-bit data +DVALID + PSYNC or recording of 10-bitraw datarecording via SPI; no checking of transportstream structure; recording of 8-bit data100 kbit/s to 90 Mbit/s (including nullpackets)max. data volume for recording limitedonly by hard disk sizedepends on net data rate of incomingtransport stream and on hard disk sizesee R&S ® SFU-K22 optionsee R&S ® SFU-K22 optionsee R&S ® SFU-B11 optionTRP player (R&S ® SFU-K22 option) (see ordering information)To output ETI data streams to external T-DMB/DAB devices, the R&S ® SFU-B11 ETI input/output option is required.ReplaySerial TS outputSerial ETI outputfile formatlength of transport stream packetsreplay time/sequence lengthdata ratedata volumemodeconnectoroutput impedanceASIoutput leveldata ratemodeSMPTE 310Moutput leveldata rateTRP, T10, BIN, TS, MPG,DAB/DAB_C, DABP_C (ETI format),FLO/FLO_C, ISDBT_Ccorresponding to externallyapplied/recorded transport streamendless (but not seamless) replay with cutat transition from end of file to beginning offilecorresponding to recording data rate andsetting (100 kbit/s to max. 90 Mbit/s) fromhard diskcorresponding to recorded data volume;limited only by hard disk sizeASI, SMPTE 310M (selectable)BNC female, rear75 800 mV270 Mbit/spacket or continuous800 mV19.392658 Mbit/ssee R&S ® SFU-B11 optionVersion 07.00, October 2008 R&S ® SFU Broadcast Test System 15

Analog basebandAnalog video/audio inputIf the external video/audio inputs are used, the analog I and Q inputs can no longer be assigned.Video inputAudio inputInternal audio signal generatorAudio signalsNICAM signalsconnectorinput level CCVSinput impedanceDC restorationconnectorQ inputI inputinput levelinput impedancenumber of signalsfrequencylevelfixed sequencesstereo1stereo2stereo3stereo4dual1dual2dual3dual4mono1mono2mono3mono4included in R&S ® SFU-K190 to -K194BNC female, front panel, I input withR&S ® SFU-Z19 adapterV pp = 1 V75 clamping of back porchBNC female, frontwith R&S ® SFU-K190 to R&S ® SFU-K194,R&S ® SFU-K170with R&S ® SFU-K1700 dBm50 2, can be set separately30 Hz to 15 kHz, in 1 Hz steps–60 dB to +12 dB, in 0.01 dB steps,6 dBu corresponds to standard deviationAF L: 1 kHzAF R: 2 kHzAF L: 1 kHzAF R: 1 kHzAF L: 1 kHzAF R: OFFAF L: OFFAF R: 1 kHzAF L: 2 kHzAF R: 5 kHzAF L: 1 kHzAF R: 1 kHzAF L: 1 kHzAF R: OFFAF L: OFFAF R: 1 kHzAF: 1 kHzAF: 4 kHzAF: 10 kHzAF: 100 Hz16 R&S ® SFU Broadcast Test System Version 07.00, October 2008

Internal video signal generator (R&S ® SFU-K23 option) (see ordering information)Internal video signal generator included in R&S ® SFU-K190 to -K194Video signalsATV video basicCOLORBARS_75 (PAL)COLORBARS_75 (PAL M)COLORBARS_75 (PAL N)COLORBARS_75 (NTSC)COLORBARS_75 (SECAM)FUBK (PAL)Insertion test signal structurein line with country-specific standardsPAL – color bar 75 %first fieldlines 8, 102T pulseline 16 data line 1line 17CCIR17line 18CCIR18/1line 19CCIR18/2lines 20, 21teletext test linesecond fieldline 329 data line 2line 330CCIR330/5line 3312T pulseline 332CCIR331/1line 333sinx/xlines 334, 335teletext test linePAL M – color bar 75 %first fieldline 17NTC7 compositeline 18FCC compositesecond fieldline 17NTC7 combinedline 18sinx/xVersion 07.00, October 2008 R&S ® SFU Broadcast Test System 17

PAL N – color bar 75 %first fieldlines 8, 102T pulseline 16 data line 1line 17CCIR17line 18CCIR18/1line 19CCIR18/2lines 20, 21teletext test linesecond fieldline 329 data line 12line 330CCIR330/5line 3312T pulseline 332CCIR331/1line 333sinx/xlines 334, 335teletext test lineNTSC – color bar 75 %first fieldline 17NTC7 compositeline 18FCC compositesecond fieldline 17NTC7 combinedline 18sinx/xSECAM – color bar 75 %first fieldlines 7 to 15discriminating signalline 16 data line 1line 17CCIR17line 18CCIR18/1line 19CCIR18/2lines 20, 21teletext test linesecond fieldlines 320 to 328discriminating signalline 330CCIR330/5line 3312T pulseline 332CCIR331/1line 333sinx/xline 334, 335teletext test linePAL – FuBKfirst fieldlines 8, 102T pulseline 16 data line 1line 17CCIR17line 18CCIR18/1line 19CCIR18/2lines 20, 21teletext test linesecond fieldline 329 data line 2line 330CCIR330/5line 3312T pulseline 332CCIR331/1line 333sinx/xlines 334, 335teletext test lineAdditional video signals ATV video see R&S ® ATV video option18 R&S ® SFU Broadcast Test System Version 07.00, October 2008

DMB-T (TDS-OFDM, R&S ® SFU-K7 option) (see ordering information)DMB-T (TDS-OFDM) in line with TDS-OFDM field trials in ChinaModulationmodeCOFDMbandwidth6 MHz, 7 MHz, 8 MHz (settable forvariable bandwidth: 5.6 MHz to7.962 MHz)modulation frequency response50 dBCodingconstellationQPSK, 16QAM, 64QAMcode rate 4/9, 2/3, 8/9guard interval 420, 945time interleaver 48, 240, 720FFT mode4k COFDMSpecial functionsbyte interleaver, randomizer, sync wordrandomizer, pilot data, guard interval,power boostcan be switched offrandomizer restartpacket/frameSingle-frequency networknetwork modeMFNcontrolMIP, manualTest signalsTS test packet (see “Internal test signals”)DTMB/DMB-TH (R&S ® SFU-K12 option) (see ordering information)DTMB (TDS-OFDM)in line with GB20600-2006DMB-TH in line with LS specification field trials in ChinaModulationmodeCOFDM/single carrierbandwidth6 MHz, 7 MHz, 8 MHzmodulation frequency response50 dBCodingconstellation4QAM, 4QAM-NR, 16QAM, 32QAM,64QAMcode rate 0.4, 0.6, 0.8guard intervalPN sequences 420, 595, 945PN sequences 420, 945variable/constantPN sequence 595constanttime interleaveroff, 240, 720 symbolsFFT mode4k COFDM/single carrierpilot carriercan be switched off (single carrier)Special functionsGI power boostcan be switched offguard interval PNcan be switched over, variable, constantLDPC outputI first, Q first, can be switched over, plus,minusQAM and QPSK constellationcan be switched overDMB-TH modecan be switched onSingle-frequency networknetwork modeMFN, SFNcontrolMIP, manualTest signalsTS test packet (see "Internal test signals")20 R&S ® SFU Broadcast Test System Version 07.00, October 2008

CMMB (R&S ® SFU-K15 option) (see ordering information) 8CMMB in line with GY/T 220.1-2006ModulationmodulationCOFDMbandwidth2 MHz, 8 MHzmodulation frequency response50 dBCodingFFT mode1K, 4Kscrambling mode 0 to 7number of timeslots 40servicesReed Solomon (240,240)(240,224)(240,192)(240,176)byte interleaver 1 to 3LDPC 1/2, 3/4constellationBPSK, QPSK, 16QAMSpecial functionsReed Solomon, byte interleaver, bitinterleaver, scramblingcan be switched offISDB-T/ ISDB-T B /ISDB-T SB (R&S ® SFU-K6 option)ISDB-T in line with ARIB STD-B31 version 1.7ISDB-T Bin line with Brazilian standardISDB-T SBin line with ARIB STD-B29ModulationmodeOFDMbandwidth6 MHz (variable: ±1000 ppm)number of segmentsARIB STD-B31 13ARIB STD-B29 1, 3MER>40 dBmodulation frequency response48 dBCodingFFT mode2k, 4k, and 8knumber of layers 1 to 3constellationQPSK, DQPSK, 16QAM, 64QAMcode rate 1/2, 2/3, 3/4, 5/6, 7/8guard interval 1/4, 1/8, 1/16, 1/32time interleaverISDB-T 0, 1, 2, 4, 8, 16ISDB-T SB 0, 1, 2, 4, 8, 16, 32Special functionsscrambler, Reed-Solomon, byteinterleaver, bit interleaver, frequencyinterleaver, guard interval, pilots, OFDMsegmentscan be switched offAC information PRBS, all "1"Test signalsTS test packet (see "Internal test signals")MediaFLO (R&S ® SFU-K10 option) (see ordering information)MediaFLOin line with QUALCOMM 80-T0455-1ModulationRev. EmodeCOFDMbandwidth5 MHz, 6 MHz, 7 MHz, 8 MHzmodulation frequency response

ATSC 8VSB (R&S ® SFU-K4 option)ATSC 8VSBin line with ATSC Doc. A/53 (8VSB)Modulationmode8VSBbandwidth6 MHzsymbol rate10.762 Mspsrange±5 % settablepilot1.25 (can be switched off)range settable (from 0 to 5 in steps of 0.001)pulse filtering root raised cosine roll-off, = 0.115MER >40 dB 9modulation frequency response45 dBCoding input data rate 19.392658 Mbit/sSpecial functions randomizer, interleaver can be switched offTest signalsTS test packet (see "Internal test signals")PRBS before convolutional encoderPRBS after convolutional encoderPRBS before mapperATSC-M/H (R&S ® SFU-K18 option) (see ordering information) 10ATSC-M/H in line with ATSC mobile TV USAATSC/A-VSB (R&S ® SFU-K14 option)ATSC/A-VSB in line with ATSC mobile TV USA field trialsModulationmode8VSBbandwidth6 MHzsymbol rate10.762 Mspsrange±5 % settablepilot1.25 (can be switched off)range settable (from 0 to 5 in steps of 0.001)pulse filtering root raised cosine roll-off, = 0.115MER>40 dBmodulation frequency response45 dBCodinginput data rate19.392658 Mbit/srange±5 % (depending on symbol rate)SRS modes 0 to 4turbo stream modes 0 to 8Special functions randomizer, interleaver can be switched offTest signalsTS test packet (see "Internal test signals")PRBS before convolutional encoderPRBS after convolutional encoderPRBS before mapper9 With internal test signals.10 In preparation; data preliminary.22 R&S ® SFU Broadcast Test System Version 07.00, October 2008

Cable standardsDVB-C/ISDB-C (R&S ® SFU-K2 option)DVB-CISDB-CModulationSpecial functionsTest signalsin line with EN 300429 (ITU-T J.83/A)in line with ITU-T J.83/Cmode16QAM, 32QAM, 64QAM,128QAM, 256QAMsymbol rate0.1 Msps to 8 Msps, settablepulse filtering root raised cosine roll-off, = 0.15,variable roll-off (0.1; 0.13; 0.15; 0.18; 0.20)MER>40 dBmodulation frequency response±0.25 dBshoulder attenuation>48 dBenergy dispersal, Reed-Solomon encoder(204, 188, t = 8), convolutional interleaver can be switched offTS test packet (see “Internal test signals”)PRBS before mapperJ.83/B (R&S ® SFU-K5 option)J.83/BModulationCodingSpecial functionsTest signalsin line with ITU-T J.83/Bmode64QAM, 256QAM, 1024QAMbandwidth6 MHzsymbol rate64QAM5.0569 Msps256QAM5.3600 Msps1024QAM5.3600 Mspspulse filteringroot raised cosine roll-off, = 0.18 (64QAM),0.12 (256QAM/1024QAM)MER>40 dBmodulation frequency response±0.25 dBshoulder attenuation64QAM>50 dB256QAM>45 dB1024QAM>45 dBinput data rate64QAM26.97035 Mbit/s256QAM38.81070 Mbit/s1024QAM49.02525 Mbit/sdata interleaver can be switched off, level 1 and level 2randomizer, Reed-Solomon encoder,interleaver, checksumcan be switched offTS test packet (see "Internal test signals")PRBS before Trellis encoderPRBS before mapperVersion 07.00, October 2008 R&S ® SFU Broadcast Test System 23

Satellite standardsDVB-S/DVB-DSNG (R&S ® SFU-K3 option)DVB-S/DVB-DSNG in line with EN 300421/EN 301210ModulationmodeQPSK, 8PSK, 16QAMsymbol rate0.1 Msps to 45 Msps, settableoverrange>45 Msps to 66 Mspspulse filtering root raised cosine roll-off, = 0.35,variable roll-off (0.25; 0.30; 0.35; 0.40;0.45)MER38 dB (27.5 Msps)modulation frequency response±0.25 dBshoulder attenuation>45 dBCodingcode rateQPSK: 1/2, 2/3, 3/4, 5/6, 7/88PSK: 2/3, 5/6, 8/916QAM: 3/4, 7/8Special functionsTest signalsenergy dispersal, Reed-Solomon encoder(204, 188, t = 8), convolutional interleaver can be switched offTS test packet (see “Internal test signals”)PRBS before convolutional encoderDVB-S2 (R&S ® SFU-K8 option) (see ordering information)DVB-S2 in line with EN 302307, broadcast servicesModulationmodeQPSK, 8PSK, 16APSK, 32APSKsymbol rateQPSK, 8PSK1 Msps to 40 Msps (overrange 45 Msps)16APSK2 Msps to 39 Msps32APSK2 Msps to 32 Mspspulse filtering root raised cosine roll-off, = 0.20,variable roll-off (0.15, 0.20, 0.25, 0.35)MER38 dB (20 Msps)modulation frequency response±0.25 dBshoulder attenuation45 dBCodingcode rateQPSK 1/4, 1/3, 2/5, 1/2, 3/5, 2/3, 3/4, 4/5, 5/6,8/9, 9/108PSK 3/5, 2/3, 3/4, 5/6, 8/9, 9/1016APSK 2/3, 3/4, 4/5, 5/6, 8/9, 9/1032APSK 3/4, 4/5, 5/6, 8/9, 9/10FEC framenormal, 64800 bit; short, 16200 bitpilot insertioncan be switched offSpecial function error insertion after CRC-8, BCH or LDPCTest signalsTS test packet (see “Internal test signals”)DIRECTV legacy modulation (R&S ® SFU-K9 option) (see ordering information)DIRECTV legacy modulationin line with DIRECTV transmissionModulationspecificationsmodeQPSKsymbol rate20 Mspsoverrange1 Msps to 30 Mspspulse filtering root raised cosine roll-off, = 0.20,variable roll-off (0.15, 0.20, 0.25, 0.35)MER38 dB (20 Msps)modulation frequency response

AMC (R&S ® SFU-K108 option) (see ordering information)AMC (advanced modulation coding) in line with AMC supports DIRECTV as well as parts ofDVB-S and phase noiseModulationmodeQPSK, H8PSKsymbol rateDVB-S: 1 Msps to 36 Msps (and up to42 Msps depending on code rate)DIRECTV: 20 Mspsoverrange for DIRECTV1 Msps to 30 Mspspulse filtering root raised cosine roll-off, = 0.20,variable roll-off (0.15, 0.20, 0.25, 0.35)MER38 dB (20 Msps)modulation frequency response

Analog modulation systemsAM/FM/RDS (R&S ® SFU-K170 option) (see ordering information)FMFM operating modesaudio signalsstereo, monoFM stereointernal audio signal generatorexternal audio inputAF frequency rangeAF frequency responseattenuation at 19 kHzpreemphasisresidual AMstereo operating modesMPX frequency deviationdeviationresolutionstereo crosstalk attenuationtotal harmonic distortionSNR (stereo/RDS signal) 11ITU-R weighted (quasi-peak)ITU-R unweighted (rms)pilot tonesee audio generatorsee analog audio input30 Hz to 15 kHz70 dBOFF, 50 μs, 75 μs50 dB (at AF = 30 Hz to 15 kHz)64 dB>70 dBfrequency19 kHz ± 1 Hzdeviation0 Hz to ±15 kHzresolution10 Hzphase 0º to ±180ºresolution 0,1ºRDSFM monoAMsubcarrier frequencydeviationresolutionmono frequency deviationdeviationresolutiontotal harmonic distortion 12audio signalsinternal audio signal generatorexternal audio inputAF frequency rangeAF frequency responseattenuation at 3.15 kHzmodulation57 kHz ±3 Hz0 Hz to ±10 kHz10 Hz0 Hz to ±100 kHz10 Hz

Standard B/G (R&S ® SFU-K190 option) (see ordering information)Standard B/Gin line with country-specific standardVision modulationmodulationB/Ggroup delayprecorrectionCCIR – B/G Germany general half (can beswitched off)frequency response60 dB weighted (CCIR)Video signalsinternal video generatorsee R&S ® SFU-K23 optionexternal video inputsee video inputAudio signals internal audio generator see audio generatorexternal audio inputsee audio inputStandard D/K (R&S ® SFU-K191 option) (see ordering information)Standard D/KVision modulationSound modulationVideo signalsAudio signalsin line with country-specific standardmodulationgroup delayprecorrectionfrequency responsevestigial sidebandfilteringamplitude frequency responseS/N ratiovideomodemodulation of sound carrier 1, 2modulation modefrequency deviationpreemphasisvision/sound carrier frequency spacingvision/sound carrier level spacingpilot toneS/N ratiosoundinternal video generatorexternal video inputinternal audio generatorexternal audio inputD/KOIRT – D/K half (can be switched off)60 dB weighted (CCIR)see R&S ® SFU-K23 optionsee video inputsee audio generatorsee audio inputVersion 07.00, October 2008 R&S ® SFU Broadcast Test System 27

Standard I (R&S ® SFU-K192 option) (see ordering information)Standard Iin line with country-specific standardVision modulationmodulationgroup delayprecorrectionfrequency responsevestigial sidebandfilteringamplitude frequency responseS/N ratiovideoSound modulationmodemodulation of sound carrier 1modulation modefrequency deviationpreemphasisvision/sound carrier frequency spacingvision/sound carrier level spacingmodulation of sound carrier 2modulation modevision/sound carrier frequency spacingvision/sound carrier level spacingS/N ratiosoundVideo signalsinternal video generatorexternal video inputAudio signalsinternal audio generatorexternal audio inputStandard M/N (R&S ® SFU-K193 option) (see ordering information)Standard M/Nin line with country-specific standardVision modulationmodulationgroup delayprecorrectionfrequency responsevestigial sidebandfilteringamplitude frequency responseS/N ratiovideoSound modulationmodemodulation of sound carrier 1, 2modulation modefrequency deviationpreemphasisvision/sound carrier frequency spacingvision/sound carrier level spacingpilotS/N ratiosoundVideo signalsinternal video generatorexternal video inputAudio signalsinternal audio generatorexternal audio inputIUK – I (can be switched off)60 dB weighted (CCIR)see R&S ® SFU-K23 optionsee video inputsee audio generatorsee audio inputM/NFCC – M/N (can be switched off)60 dB weighted (CCIR)see R&S ® SFU-K23 optionsee video inputsee audio generatorsee audio input28 R&S ® SFU Broadcast Test System Version 07.00, October 2008

Standard L (R&S ® SFU-K194 option) (see ordering information)Standard Lin line with country-specific standardVision modulationmodulationgroup delayprecorrectionfrequency responsevestigial sidebandfilteringamplitude frequency responseSound modulationmodemodulation of sound carrier 1modulation modevision/sound carrier frequency spacingvision/sound carrier level spacingmodulation of sound carrier 2modulation modefrequency deviationvision/sound carrier frequency spacingvision/sound carrier level spacingVideo signalsinternal video generatorexternal video inputAudio signalsinternal audio generatorexternal audio inputLTDF - L (can be switched off)

Standard PAL I1Standard PAL D/KStandard PAL D1Standard M/NStandard SECAM Limplementationin line with MBRAI PAL-I1video test signal PAL I1 – color bar 75 %insertion test signal structuresee belowsound subcarriersound 1FM 50 kHz deviation /6.0 MHz/13 dBsound 2 NICAM 14roll-off = 100 %/6.552 MHz /20 dBaudio codingmonosound 11 kHzgroup delay precorrectionnoneresidual carrier 20 %video test signalPAL D/K – FuBKinsertion test signal structuresee belowsound subcarriersound 1FM 50 kHz deviation/6.5 MHz/13 dBsound 2FM 50 kHz deviation/6.74 MHz/20 dBaudio codingstereoleft1 kHzright1 kHzgroup delay precorrectionflatresidual carrier 12.5 %implementationin line with MBRAI PAL-D1video test signal PAL D1 – color bar 75 %insertion test signal structuresee belowsound subcarriersound 1FM 50 kHz deviation /6.5 MHz/13 dBsound 2 NICAM 14roll-off = 40 %/5.85 MHz /20 dBaudio codingmonosound 11 kHzgroup delay precorrectionhalf, OIRTresidual carrier 12.5 %video test signalNTSC M – SMPTE color bar with PLUGEinsertion test signal structuresee belowsound subcarrierFM 50 kHz deviation /4.5 MHz/7 dBaudio codingmonosound 1400 Hzgroup delay precorrection5 MHz/FCCresidual carrier 12.5 %implementationin line with MBRAI SECAM Lvideo test signal SECAM L – color bar 75 %insertion test signal structuresee belowsound subcarriersound 1NICAM 14 roll-off = 40 %/5.85 MHz/27 dBsound 2 AM modulation depth =54 %/6.5 MHz/10 dBaudio codingsound 1monosound 21 kHzgroup delay precorrectionfull, TDFresidual carrier 3 %14 Simulation of NICAM spectrum by means of PN sequence and appropriate pulse shaping.30 R&S ® SFU Broadcast Test System Version 07.00, October 2008

Insertion test signal structure in line with country-specific standardsStandards B/G,B/G N, I, I1 , D/K, D1 andstandard IEC 62002 withfirst fieldlines 8, 102T pulse2 CH. PAL B (MBRAI)line 16 data line 12 CH. PAL G (MBRAI)lines 17, 18CCIR172 CH. PAL B N (MBRAI)line 19CCIR18/22 CH. PAL G N (MBRAI)lines 20, 21teletext test line2 CH. PAL I1 (MBRAI)2 CH. PAL D1 (MBRAI)second fieldline 323teletext test lineDVB-T + PAL B (MBRAI)line 329 data line 2DVB-T + PAL G (MBRAI)lines 330, 331CCIR330/5DVB-T + PAL B N (MBRAI)line 332CCIR331/1DVB-T + PAL G N (MBRAI)line 333sinx/xDVB-T + PAL I1 (MBRAI)lines 334, 335teletext test lineDVB-T + PAL D1 (MBRAI)Standard M/Nfirst fieldline 17NTC7 compositeline 18FCC compositesecond fieldline 17NTC7 combinedline 18sinx/xStandard L andstandard IEC 62002 withfirst fieldlines 7 to 14discriminating signalDVB-T + SECAM L (MBRAI),line 15teletext test line2 CH. SECAM L (MBRAI)line 17CCIR17line 18CCIR18, 6 multiburst packetssecond fieldlines 320 to 328discriminating signalline 330CCIR330lines 331, 332CCIR331line 333CCIR331/1MBRAI signal combinationsSignal combinationsin line with IEC 62002 (MBRAI)Digital/analog multi-interfererpattern L1digital N+2/analog N+4 signalDVB-T + PAL B (MBRAI)DVB-T + PAL G (MBRAI)DVB-T + PAL B N (MBRAI)DVB-T + PAL G N (MBRAI)DVB-T + PAL I1 (MBRAI)DVB-T + PAL D1 (MBRAI)DVB-T + SECAM L (MBRAI)Analog multi-interfererpattern L22 analog N+2/N+4 signals2 CH. PAL B (MBRAI)2 CH. PAL G (MBRAI)2 CH. PAL B N (MBRAI)2 CH. PAL G N (MBRAI)2 CH. PAL I1 (MBRAI)2 CH. PAL D1 (MBRAI)2 CH. SECAM L (MBRAI)Version 07.00, October 2008 R&S ® SFU Broadcast Test System 31

SimulationArbitrary waveform generator (R&S ® SFU-K35 option) (see ordering information)Waveform memorylength512 sample to 128 Msamplein one-sample stepsresolution16 bitloading time for 10 Msample3 snonvolatile memoryhard diskClock generationclock rate400 Hz to 100 MHzaccuracy0.001 Hzoperating modeinternalfrequency accuracy (internal)accuracy of reference frequencyInterpolationbandwidthwith clock rate = 100 MHz(no interpolation), bandwidth 0.1 dB 40 MHzwith clock rate

T-DMB/DAB waveforms (R&S ® SFU-K351 option)T-DMB/DAB waveformsI/Q sequences with audio and videocontentsfor details see description of optionTransmission modulation I, IISignal setvideoresolution CIF (352 × 288), QCIF (176 × 144),QVGA (320 × 240)sequencesdiver, fishesaudiobackground musicaudio program servicesignal1 kHz sinewavelevel0 dBFSsampling rate48 kHzmodestereodata rate192 kbit/sSpecial function Gaussian fading profiles included, can be used with R&S ® SFU-B30optionDVB-H waveforms (R&S ® SFU-K352 option)DVB-H waveformsI/Q sequences with audio and videocontentsfor details see description of optionTransmission mode different DVB-H modesSignal set video/audio different resolutions and sequencesDRM waveforms (R&S ® SFU-K353 option)DRM waveforms I/Q sequences with audio contents for details see description of optionTransmissionmodeA, B, C, and Dconstellation4QAM, 16QAM, and 64QAM (OFDM)bandwidth4.5 kHz, 5 kHz, 9 kHz, 10 kHz, 18 kHz,20 kHzsampling rate12 kHz, 48 kHzSignal setaudiosignaldifferent sequenceslevel–10 dBFS, –12 dBFSmodemonocodingMPEG-4 AAC, MPEG-4 CELPdata rate4.8 kbit/s to 30.6 kbit/sDTV interferers (R&S ® SFU-K354 option)DTV interferersI/Q sequences in line with country-specificstandards,IEC 62002 MBRAI, NORDIG, Dbook, A.74 for details see description of optionWaveformslength512 sample to 128 Msampleresolution16 bitloading time for 64 Msample20 snonvolatile memoryhard diskSignal set standards DVB-T, ATSC/8VSB, T-DMB/DAB,MediaFLO, ISDB-T, ISDB-T SB , FMDVB-T standardlengthsuperframesingle-interferer sequencebandwidth5 MHz, 6 MHz, 7 MHz, 8 MHzFFT mode8kconstellation16QAMcode rate 2/3guard interval 1/8multi-interferer sequencepatternpattern L3 (2 DVB-T signals N+2/N+4)bandwidth8 MHzFFT mode8kconstellation16QAMcode rate 2/3guard interval 1/8Version 07.00, October 2008 R&S ® SFU Broadcast Test System 33

ATSC/8VSB standardStandard MediaFLOStandard DTMB (GB20600-2006)T-DMB/DAB standardlengthsequenceslengthbandwidthlengthmodebandwidthconstellationlengthmodebandwidthsingle-interferer sequencemulti-interferer sequencetwo channelsthree channels1 data framecenter frequency, pilot frequency1 s6 MHz1 ssingle carrier/multicarrier8 MHz4QAM, 16QAM, 32QAM, 64QAM/16QAMframemode I8 MHzcenter frequencyA, D, with frequency gap B, CA, C, with frequency gap B, D withfrequency offset 1.712 MHzA, B, with frequency gap C, D, withfrequency offset 3.424 MHzA, B, C, with frequency offset 1.712 MHzA, C, D, with frequency gap BA, B, D, with frequency gap CA, B, C, Dapprox. 231 msStandard ISDB-T SBfour channelsStandard ISDB-Tlengthsingle-interferer sequenceOFDM segments 1, 3lengthapprox. 202 ms, 231 mssingle-interferer sequenceOFDM segments 1, 3Standard FMlengthsingle-interferer sequenceFM jammerfrequencyfrequency deviationframeinfinite seamless1 kHz±50 kHz (in line with GSM900 TX)MediaFLO waveforms (R&S ® SFU-K355 option)MediaFLO waveforms I/Q sequences in line with MediaFLO for details see description of optionTransmissioncontentdatalength6 superframes, 6 secondsbandwidth6 MHzSignal setwide area ID 15local area ID 10 and 15dataseveral MediaFLO IDs with different TXmodes depending on sequence34 R&S ® SFU Broadcast Test System Version 07.00, October 2008

Cable interferers (R&S ® SFU-K356 option)Cable interferersI/Q sequences in line with country-specificstandardsfor details see description of optionSignal setstandardsdigital: J.83/Banalog: M/NStandard J.83/B sequences 64QAM, 256QAM:digital/digitalStandard M/N sequences analog/analogHD Radio waveforms (R&S ® SFU-K357 option) 16HD Radio waveforms I/Q sequences in line with Ibiquity for details see description of optionCMMB waveforms (R&S ® SFU-K358 option) 17CMMB waveforms I/Q sequences in line with CMMB for details see description of optionInterferer management (R&S ® SFU-K37 option)Interferermodebandwidthlevel setting rangefrequency offsetpoints for adding interferer signalsSignal setARB, ATV predefined, analog I/Q,digital I/Q96 MHzNoisedensity distribution functionGaussian, statistical, separate for I and Qcrest factor18 dBC/Nsetting range–30 dB to +60 dBresolution0.1 dBuncertainty for system bandwidth =symbol rate and C/N

Phase noise (R&S ® SFU-K41 option)Phase noisefrequency responseselection from profile filesamplitude at f carrier ±100 Hzsetting range–10.0 dBc/Hz to –110.0 dBc/Hz,depending on selected profileresolution0.1 dBmax. phase angle ±180°density distribution functionGaussianSystem bandwidth sampling rate 10 MHzProfile filesphase noise maskspredefined filesformattext files, editableSpecial functioncustomer-specific files can be usedPLL phase noise masksPLL1simulation of typ. PLL circuitsfrequency max. phase noise100 Hz –18.5 dBc/Hz1 kHz –30.2 dBc/Hz10 kHz –44.5 dBc/Hz100 kHz –56.5 dBc/Hz1 MHz –77.8 dBc/HzPLL2frequency max. phase noise100 Hz –22.4 dBc/Hz1 kHz –32.0 dBc/Hz10 kHz –43.5 dBc/Hz100 kHz –83.5 dBc/Hz1 MHz –99.4 dBc/HzVCXO phase noise masksCyrstall1simulation of typ. oscillator circuitsfrequency max. phase noise100 Hz –12.9 dBc/Hz1 kHz –15.4 dBc/Hz10 kHz –38.6 dBc/Hz100 kHz –59.7 dBc/Hz1 MHz –79.3 dBc/HzCyrstall2frequency max. phase noise100 Hz –13.2 dBc/Hz1 kHz –16.1 dBc/Hz10 kHz –40.3 dBc/Hz100 kHz –61.5 dBc/Hz1 MHz –80.7 dBc/Hz36 R&S ® SFU Broadcast Test System Version 07.00, October 2008

Cyrstall3frequency max. phase noise100 Hz –22.3 dBc/Hz1 kHz –24.9 dBc/Hz10 kHz –50.9 dBc/Hz100 kHz –66.6 dBc/Hz1 MHz –72.6 dBc/HzCyrstall4frequency max. phase noise100 Hz –22.3 dBc/Hz1 kHz –31.1 dBc/Hz10 kHz –61.6 dBc/Hz100 kHz –59.5 dBc/Hz1 MHz –105.8 dBc/HzCyrstall5frequency max. phase noise100 Hz –22.5 dBc/Hz1 kHz –23.1 dBc/Hz10 kHz –41.2 dBc/Hz100 kHz –78.8 dBc/Hz1 MHz –98.2 dBc/HzDVB-S2 phase noise masksDVB-S2 P1based on EN 302 307, DIRECTVfrequency max. phase noise100 Hz –20.1 dBc/Hz1 kHz –22.6 dBc/Hz10 kHz –45.6 dBc/Hz100 kHz –66.7 dBc/Hz1 MHz –86.4 dBc/HzDVB-S2 P2frequency max. phase noise100 Hz –20.1 dBc/Hz1 kHz –22.8 dBc/Hz10 kHz –46.9 dBc/Hz100 kHz –68.2 dBc/Hz1 MHz –87.5 dBc/HzVersion 07.00, October 2008 R&S ® SFU Broadcast Test System 37

DVB-S2 D1frequency max. phase noise100 Hz –12.5 dBc/Hz1 kHz –24.0 dBc/Hz10 kHz –48.0 dBc/Hz100 kHz –65.5 dBc/Hz1 MHz –73.8 dBc/HzDVB-S2 A1frequency max. phase noise100 Hz –18.6 dBc/Hz1 kHz –44.2 dBc/Hz10 kHz –66.35 dBc/Hz100 kHz –86.0 dBc/Hz1 MHz –97.5 dBc/HzDVB-S2 A2frequency max. phase noise100 Hz –20.0 dBc/Hz1 kHz –45.4 dBc/Hz10 kHz –67.7 dBc/Hz100 kHz –79.3 dBc/Hz1 MHz –93.8 dBc/HzSpecial functionown files can be used38 R&S ® SFU Broadcast Test System Version 07.00, October 2008

Impulsive noise (R&S ® SFU-K42 option)Pulsed addition of an AWGN signal to the useful signal with settable number of pulses per frame and within settable limits of randomlydistributed pulse intervals.AWGN signal (not pulsed) data see R&S ® SFU-K40 optionPulse generatorFrame duration 10 ms, 100 ms, 1000 msPulse duration 0.25 μs, fixedPulses per frame setting range 1 to 40000Minimum pulse intervalfor number of pulses >1setting range0.25 μs to 16 msresolution0.25 μsMaximum pulse intervalfor number of pulses >1setting range0.25 μs to 16 msresolution0.25 μsDistribution of pulse intervals function PRBSMultinoise use (R&S ® SFU-K43 option) (see ordering information)Selectable noise sources can be combined to form a cumulative noise signal, which is then added to the useful signal. The C/N andlevel can be set for the overall signal. R&S ® SFU broadcast test systems delivered before May 2006 require a hardwareSignal sourcesCumulative signalC/N setting for cumulative signalextension. 19 AWGN noise see R&S ® SFU-K40 optionphase noiseimpulsive noisesignal sources that can be combinedAWGN noisephase noiseimpulsive noisesetting rangeresolutionuncertainty for system bandwidth = symbolrate and C/N

Fading simulator (R&S ® SFU-B30 option)Number of paths20with R&S ® SFU-B31 option 40System bandwidth80 MHzPath lossrange0 dB to 50 dBresolution0.01 dBaccuracy93 hpower density functionS(i,f) = G (A; f: 0.1fd)Lognormal fadingstandard deviation0 dB to 12 dBresolution1 dBlocal constant12 m to 200 m for f RF = 1 GHz20 Ratio of discrete component to distributed component.40 R&S ® SFU Broadcast Test System Version 07.00, October 2008

Enhanced fading (R&S ® SFU-K30 option) (see ordering information)30 MHz fine delay mode50 MHz fine delay modeMoving delay modeBirth-death modeTwo-path dynamic delaynumber of paths12, 24 (with R&S ® SFU-B31 option)system bandwidth30 MHzpath delaysee R&S ® SFU-B30 optionresolution0.01 nsnumber of paths8, 16 (with R&S ® SFU-B31 option)system bandwidth50 MHzpath delaysee R&S ® SFU-B30 optionresolution0.01 nssystem bandwidth50 MHzfadingnumber of fading paths2 per signal pathprofilenonereference pathdelay0 μs to 40 μsresolution10 nsmoving delay pathmean delay150 ns to 39.85 μsdelay variation0.3 μs to 40 μsresolution10 nsvariation period10 s to 500 s in steps of 100 mssystem bandwidth50 MHzfadingnumber of fading paths2 per signal pathprofilepure Dopplerspeed rangesee R&S ® SFU-B30 optionDoppler frequency rangesee R&S ® SFU-B30 optiondelayminimum delay 0 μs to 40 μs 21delay grid 100 ns to 40/3 μs 21resolution1 nsgrid positions 3 to 50 21hopping parametersstart offset0 s to 429 shopping dwell time1 ms to 429 stotal (start offset + hopping dwell time) max. 429 sresolution100 nssystem bandwidth50 MHzfadingnumber of fading paths2 per signal pathmoving modehopping/slidinghopping positions2/alternatingsliding functionsinusoidalprofilestatic, pure Doppler, Rayleighspeed rangesee R&S ® SFU-B30 optionDoppler frequency rangesee R&S ® SFU-B30 optiondelayreference path (statistically in delay) 0 s to 1638.00 μsmoving pathminimum delay0 s to 1000.00 μsmaximum delay0 s to 1000.00 μsresolution10 nshopping dwell time100 ms to 10 ssliding period50 s to 1000 sresolution10 ms21 The maximum delay range of 40 μs may not be exceeded.Version 07.00, October 2008 R&S ® SFU Broadcast Test System 41

Gaussian fading (R&S ® SFU-K32 option) (see ordering information)Gaussian fading profiles in line with EN 50248GAUS1amplitude distributionpseudo noise interval >93 hpower density function S(i,f) = G (A, –0.8fd, 0.05fd) +G (A1, + 0.4fd, 0.1fd), where A1 is 10 dBless than AGAUS2amplitude distributionpseudo noise interval >93 hpower density function S(i,f) = G (B, + 0.7fd, 0.1fd) +G (B1, – 0.4fd, 0.15fd), where B1 is 15 dBless than BGAUSDABamplitude distributionpseudo noise interval >93 hpower density functionS(i,f) = G (A, ±0.7fd, 0.1fd)where +0.7fd is used for paths of evenpath number, and –0.7fd is used for pathsof uneven path number;path 1 is an exception and isparameterized with +0.7fdAnalysisRF power measurement (R&S ® SFU-K55 option)The power measurement requires the use of R&S ® NRP-Zxx power sensors.RF power measurementsPower measurementOperating modeFilterRangePower sensorsfor analog and digital modulation modesdisplayunitsautouserautouseroptimizationlengthfrequency rangelevel rangedynamic rangeconnectorscalibrationsupported power sensorsmeasured powerrelative powerW, dBm, dBμV, selectablemeasurement frequency coupled to RFfrequencymeasurement frequency user-selectableautomatic setting of filter lengthmanual setting of filter lengthauto once0 to 128, settabledepending on the R&S ® NRP-Zxx powersensor being usedUSB, BNC female, frontzeroR&S ® NRP-Z11, R&S ® NRP-Z21,R&S ® NRP-Z22, R&S ® NRP-Z23,R&S ® NRP-Z24, R&S ® NRP-Z51,R&S ® NRP-Z52, R&S ® NRP-Z55,R&S ® NRP-Z9142 R&S ® SFU Broadcast Test System Version 07.00, October 2008

BER measurements (R&S ® SFU-K60 option)For DVB-S2, DIRECTV, DTMB/DMB-TH and MediaFLO, BER measurements cannot be performed at all or only to a limited extent.BER measurementsfor all digital modulation modesDisplaymeasured valueBERerror countmeasurement timeStart/restartmanualPRBS measurementsInputs for BER clock, BER data, BER connectorsBNC female, rearenableinput impedance50 input levelHCTBER datainput data rateup to 90 Mbit/sPRBS2 23 –1/2 15 –1 (in line with ITU-T O.151)BER clock, BER data polarity normal, invertedBER enablealways, active high, active lowOutput for BER errorconnectorBNC female, rearoutput impedance50 output levelHCTMPEG-2 TS measurementsInputinput interfacesASI, SPI (stuffing off), SMPTE 310 (seeMPEG 2 inputs)input signalTS packet (see “Internal test signals”)payload (PRBS in line with ITU-T O.151) 2 23 –1/2 15 –1PIDNULL (1FFF (hex)), variableDATA VALIDapplicable to SPI interfaceactivealwaysTrigger inputs/outputsTriggers and connections reserved for future useTriggers 1 to 10 IN/OUTconnectorinput impedanceload resistorinput/output levelMain trigger INconnectorinput impedanceinput levelMain trigger OUTconnectorload resistoroutput levelD-Sub female, 25 pins, rearhigh impedance>200 HCTBNC female, rear50 HCTBNC female, rear>200 HCTVersion 07.00, October 2008 R&S ® SFU Broadcast Test System 43

General dataSystem dataSystemoperating systemPC platformWindows XP Embeddedinternal hard diskmemories for settings 50Local controldisplay XVGA 1024 × 768controlsrotary knob, hardkeys, and softkeysExternal control controls external mouse and keyboard via USBRemote controlcommand set SCPI 1999.5IEC/IEEE IEC 60625 (IEEE 488)address range 1 to 30IEC/IEEE interface functionsSH1, AH1, T6, L4, SR1, RL1, PP1, DC1,DT1, C0Ethernet10/100BaseTUSB 2.0ConnectorsIEC/IEEEAmphenol, 24 pins, rearEthernetRJ-45, rearUSBUSB, front and rearAC supply inputIEC 60320 C14, rearOperating dataPower supplyinput voltage range100 V to 240 VAC, nominal3.6 A to 1.3 AAC supply frequency47 Hz to 63 Hzpower factor correction in line with EN 61000-3-2EMC in line with EN 55011 class B, EN 61326Immunity to interfering field strengthup to 10 V/mEnvironmental conditionsoperating temperature range +5 °C to +45 °C 22in line with EN 60068-2-1, EN 60068-2-2storage temperature range –20 °C to +60 °Cclimatic resistance, 95 % rel. humidity, in line with EN 60068-2-3, EN 60068-2-30cyclic test at +25 °C/+40 °CMechanical resistancevibration, sinusoidal5 Hz to 150 Hz, max. 2 g at 55 Hz,55 Hz to 150 Hz, 0.5 g const.,in line with EN 60068-2-6vibration, random10 Hz to 300 Hz, acceleration 1.2 g (rms),in line with EN 60068-2-64shock40 g shock spectrum,in line with EN 60068-2-27, MIL-STD-810EElectrical safetyin line with IEC 61010-1, EN 61010-1 andUL 61010B-1, CSA C22.2 Nr. 1010.1Dimensions W × H × D 435 mm × 192 mm × 460 mm (4 HU)17.14 in × 7.56 in × 18.12 in (4 HU)Weight fully equipped 15 kg33.1 lbRecommended calibration interval3 yearsStandard warranty period1 year22 Reduced brightness of LCD at higher operating temperatures.44 R&S ® SFU Broadcast Test System Version 07.00, October 2008

Ordering informationOption identification: R&S ® SFU-Bxy = hardware option, R&S ® SFU-Kxy = software option.Delivery of R&S ® SFU base unit only with at least one coder or with the R&S ® SFU-K81 option installed.If the R&S ® SFU-K81 option is installed, no digital or analog modulation system can be used.Designation Type Order No.Broadcast Test SystemR&S ® SFU 2110.2500.02including power cable, hardcopy of quick start guide,CD-ROM (includes operating manuals and quick start guide)OptionsBasic configurationRealtime DisabledR&S ® SFU-K81 2110.7960.02(option available only at initial delivery)Realtime EnabledR&S ® SFU-K82 2110.7976.02(only if R&S ® SFU-K81 is installed)RF pathHigh Power R&S ® SFU-B90 2110.8008.03Digital modulation systemsDVB-T/H Coder R&S ® SFU-K1 2110.7301.02DVB-C/ISDB-C Coder R&S ® SFU-K2 2110.7324.02DVB-S/DVB-DSNG Coder R&S ® SFU-K3 2110.7330.02DVB-S2 Coder (requires an installed R&S ® SFU-B1 or R&S ® SFU- R&S ® SFU-K8 2110.7399.02B10)ATSC/ 8VSB Coder R&S ® SFU-K4 2110.7353.02ATSC/ A-VSB Coder R&S ® SFU-K14 only on requestATSC M/H 23 Coder R&S ® SFU-K18 only on requestJ.83/B Coder R&S ® SFU-K5 2110.7360.02ISDB-T/ISDB-T B /ISDB-T SB Coder R&S ® SFU-K6 2110.7376.02MediaFLO CoderR&S ® SFU-K10 2110.7524.02(requires an installed R&S ® SFU-B10)T-DMB/DAB Coder R&S ® SFU-K11 2110.7518.02DMB-T (TDS-OFDM) Coder (requires an installed R&S ® SFU-B1 R&S ® SFU-K7only on requestor R&S ® SFU-B10)DTMB/DMB-TH (TDS-OFDM) Coder (requires an installed R&S ® SFU-K12 2110.7760.02R&S ® SFU-B1 or R&S ® SFU-B10)Coder CMMB 23R&S ® SFU-K15 2110.7818.02(requires an installed R&S ® SFU-B1 or R&S ® SFU-B10)DIRECTV Legacy Modulation Coder (requires an installed R&S ® SFU-K9 2110.7401.02R&S ® SFU-B1 or R&S ® SFU-B10)AMC CoderR&S ® SFU-K108only on request(requires an installed R&S ® SFU-K8 (DVB-S2)and an installed R&S ® SFU-B1 or R&S ® SFU-B10)Coder Extension 1 R&S ® SFU-B1 2110.7424.02Coder Extension 10 R&S ® SFU-B10 2110.7747.02Analog modulation systemsCoder AM/FM RDSR&S ® SFU-K170 2110.7830.02(requires an installed R&S ® SFU-B2)ATV Standard B/G CoderR&S ® SFU-K190 2110.8050.02(requires an installed R&S ® SFU-B2)ATV Standard D/K CoderR&S ® SFU-K191 2110.8037.02(requires an installed R&S ® SFU-B2)ATV Standard I CoderR&S ® SFU-K192 2110.8043.02(requires an installed R&S ® SFU-B2)ATV Standard M/N CoderR&S ® SFU-K193 2110.8066.02(requires an installed R&S ® SFU-B2)ATV Standard L CoderR&S ® SFU-K194 2110.8072.02(requires an installed R&S ® SFU-B2)Multi ATV PredefinedR&S ® SFU-K199 2110.8089.02(requires an installed R&S ® SFU-B3)Coder Extension 2preinstalled in R&S ® SFU from serial no. 101000R&S ® SFU-B2 2110.7430.0223 In preparation.Version 07.00, October 2008 R&S ® SFU Broadcast Test System 45

SimulationFading Simulator R&S ® SFU-B30 2110.7530.02Fading Simulator Extension to 40 PathsR&S ® SFU-B31 2110.7547.02(requires an installed R&S ® SFU-B30)Enhanced FadingR&S ® SFU-K30 2110.7560.02(requires an installed R&S ® SFU-B30)Gaussian FadingR&S ® SFU-K32 2110.7630.02(requires an installed R&S ® SFU-B30)(included in R&S ® SFU-B30 option)ARB GeneratorR&S ® SFU-K35 2110.7601.02(requires an installed R&S ® SFU-B3)Memory Extension 1R&S ® SFU-B3 2110.7447.02preinstalled in R&S ® SFU from serial no. 101000T-DMB/DAB WaveformsR&S ® SFU-K351 2110.4277.02(can be used with R&S ® SFU-K35)DVB-H WaveformsR&S ® SFU-K352 2110.4425.02(can be used with R&S ® SFU-K35)DRM WaveformsR&S ® SFU-K353 2110.4554.02(can be used with R&S ® SFU-K35)DTV InterferersR&S ® SFU-K354 2110.4690.02(can be used with R&S ® SFU-K35)MediaFLO WaveformsR&S ® SFU-K355 2110.2974.02(can be used with R&S ® SFU-K35)Cable InterferersR&S ® SFU-K356 2110.3212.02(can be used with R&S ® SFU-K35)HD Radio WaveformsR&S ® SFU-K357only on request(can be used with R&S ® SFU-K35, Ibiquity license required)CMMB Waveforms 24R&S ® SFU-K358only on request(can be used with R&S ® SFU-K35)Interferer Management R&S ® SFU-K37 2110.7647.02AWGN Noise R&S ® SFU-K40 2110.7653.02Phase Noise R&S ® SFU-K41 2110.7660.02Impulsive Noise R&S ® SFU-K42 2110.7676.02Multinoise UseR&S ® SFU-K43 2110.7682.02(requires at least one installed R&S ® SFU-K40, R&S ® SFU-K41, orR&S ® SFU-K42)Custom OFDMR&S ® SMU-K15 1160.6402.02(generates customer-specific OFDM signals)Baseband inputs/outputsExtended I/Q R&S ® SFU-K80 2110.7953.02ETI Input/Output R&S ® SFU-B11 2110.7553.03Digital basebandTS Generator including SDTV streams R&S ® SFU-K20 2110.7476.02DVB-H Stream LibraryR&S ® DV-DVBH 2085.8704.02(requires an installed R&S ® SFU-K20)Test Card M StreamsR&S ® DV-TCM 2085.7708.02(requires an installed R&S ® SFU-K20)HDTV SequencesR&S ® DV-HDTV 2085.7650.02(requires an installed R&S ® SFU-K20)H.264 Stream LibraryR&S ® DV-H264 2085.9052.02(requires an installed R&S ® SFU-K20)ISDB-T Stream LibraryR&S ® DV-ISDBT 2085.9146.02(requires an installed R&S ® SFU-K20)TRP PlayerR&S ® SFU-K22 2110.7499.02(requires an installed R&S ® SFU-B6 and an installed R&S ® SFU-B4)TS/ETI RecorderR&S ® SFU-K21 2110.7482.02(requires an installed R&S ® SFU-K22, R&S ® SFU-B6, andR&S ® SFU-B4)Memory Extension 2 R&S ® SFU-B4 2110.7453.02Additional Hard Diskfor instruments with serial numbers

Additional Hard Diskfor instruments with serial numbers >101000T-DMB/DAB Streams(requires an installed R&S ® SFU-K22)DAB+ Streams(requires an installed R&S ® SFU-K22)MediaFLO Streams(requires an installed R&S ® SFU-K22)ISDB-T Streams(requires an installed R&S ® SFU-K22)R&S ® SFU-B6 2110.7501.03R&S ® SFU-K221 2110.4348.02R&S ® SFU-K223 2110.4760.02R&S ® SFU-K222 2110.2968.02R&S ® SFU-K224 2110.4777.02Analog basebandVideo GeneratorR&S ® SFU-K23 2110.7799.02(included in R&S ® SFU-K190 to -K194)ATV Video Signals (can be used with R&S ® SFU-K190 toR&S ® ATV Video 2110.4831.02R&S ® SFU-K194)Impedance Matching Pad 75/50 Ohms (can be used with R&S ® SFU-Z19 2110.7276.02R&S ® SFU-K190 to R&S ® SFU-K194)Measurement and analysis functionsRF Power MeasurementsR&S ® SFU-K55 2110.7753.02(can be used with R&S ® NRP-Zxx power sensors)BER MeasurementsR&S ® SFU-K60 2110.7782.02(cannot be used at all or only to a limited extent for DVB-S2,DIRECTV, DTMB, DMB-TH, and MediaFLO)Other expansionsUser I/O (additional input/output)R&S ® SFU-B5 2110.7460.02(supported by R&S ® SFU firmware versions

Service you can rely onJ In 70 countriesJ Person-to-personJ J Quality with a warrantyJ No hidden termsAbout Rohde & SchwarzRohde & Schwarz is an independent group of companiesspecializing in electronics. It is a leading supplier of solutionsin the fields of test and measurement, broadcasting,radiomonitoring and radiolocation, as well as secure communications.Established 75 years ago, Rohde &Schwarzhas a global presence and a dedicated service network inover 70 countries. Company headquarters are in Munich,Germany.Regional contactEurope, Africa, Middle East+49 1805 12 42 42* or +49 89 4129 137 74customersupport@rohde-schwarz.comNorth America1-888-TEST-RSA (1-888-837-8772)customer.support@rsa.rohde-schwarz.comLatin America+1-410-910-7988customersupport.la@rohde-schwarz.comAsia/Pacific+65 65 13 04 88customersupport.asia@rohde-schwarz.comISO 14001For product brochure,see PD 0758.1658.12and www.rohde-schwarz.comRohde&Schwarz GmbH&Co. KGMühldorfstraße 15 | 81671 MünchenPhone +4989 41290 | Fax +4989 4129 12164www.rohde-schwarz.comR&S® is a registered trademark of Rohde&Schwarz GmbH&Co. KGTrade names are trademarks of the owners | Printed in Germany (ed)PD 0758.1658.22 | Version 07.00 | Oktober 2008 | R&S®SFUSubject to change*0.14 €/min within German wireline network; rates may vary in othernetworks (wireline and mobile) and countries.