Download - Frank's Hospital Workshop

More documents

Recommendations

Info

GUIDO RAYOS X, S.A.161=OXYG, 2=HUMIDNOTE:DUE TO THE WEAR OF THE OXYGEN CELL SENSOR IT ISRECOMMENDED TO PERFORM PERIODICALLY ITS CALIBRATION PROCEDURES.Check the Oxygen Sensor is pluged on the front panel and its housing isnot located inside the Tent Hood, allow to stabilize.Press 1, the LCD will display,AIR=__._ ºCOX: 1=PRG, 2=CALPress 2, the LCD will display ,OX CALIBR (21 %)PRESS ENTERBy pressing ENTER, the Oxygen Sensor is already calibrated with a newreference.New screen displayed ;AIR=__._ ºCOX: 1=PRG, 2=CALII.6. ALARMSThe NESTOMAT 6050 Alarm System informs to the medical attendant of anyincidence may occur. The alarm is visible and audible.NOMENCLATURE OF SYMBOLS IN ALARMMESSAGES+ Excess temperature alarm- Failing temperature alarm= Temperautre O.K.* Desactive sensorA) AIR CONTROL MODEMAN-012Sept.00Ed. 1 / Rev. 3NESTOMAT 6050
GUIDO RAYOS X, S.A.171. SENSOR ALARM:In case of air sensor failure or it gets disconnected or out of range; theSENSOR Alarm will activate the corresponding LED and buzzer, thealarm cannot be silenced. The LCD will inform to the attendantdisplaying ,* ALARM *AIR SENSORThe Radiant warmer is now out of service. Call to any authorized Serviceengineer.2. LOW TEMPERATURE ALARM:Is activated when temperature reaches aproximately 1 ºC below the presettemperature (See paragrap II.10 to change preset temperature alarmrange). "LOW" alarm LED will lit, to silence acoustic alarm pressSILENCE key. The LCD will display* ALARM *AT - RH OXThe alarm can be silenced by pressing the SILENCE key. If SILENCEwas pressed and the alarm conditions remain during a period of tenminutes, the alarm will be activated again.3. HIGH TEMPERATUREIs activated when the temperature reaches aproximately 1 ºC higher thanthe preset temperature (See paragrap II.10 to change preset temperaturealarm range). "HIGH" alarm LED will lit and the LCD will display ,* ALARM *AT + RH OXto silence acoustic alarm press SILENCE key. If SILENCE was pressedand the alarm conditions remain during a period of ten minutes, the alarmwill be activated again.Check if heat sources are close to the Radiant warmer location, if positivekeep them away. If the alarm is still effective unplug the unit from thepower source, remove the patient from the radiant warmer and call to theauthorised service engineer.B) SERVO CONTROL MODE1. SENSOR ALARM:MAN-012Sept.00Ed. 1 / Rev. 3NESTOMAT 6050
Page 1 and 2: GUIDO RAYOS X, S.A.1INDEXDisclaimer
Page 3 and 4: GUIDO RAYOS X, S.A.3DISCLAIMERThe s
Page 5 and 6: GUIDO RAYOS X, S.A.5SPECIFICATIONSD
Page 7 and 8: GUIDO RAYOS X, S.A.7(1) HEAT/CALOR
Page 9 and 10: GUIDO RAYOS X, S.A.91 I/O Start up
Page 11 and 12: GUIDO RAYOS X, S.A.11• Press any
Page 13 and 14: GUIDO RAYOS X, S.A.13AT=__._ ºC (_
Page 15: GUIDO RAYOS X, S.A.15II.5 OXYGEN MO
Page 19 and 20: GUIDO RAYOS X, S.A.19C) POWER FAILU
Page 21 and 22: GUIDO RAYOS X, S.A.211 DISPL 16 CAR
Page 23 and 24: GUIDO RAYOS X, S.A.23IV. OPTIONAL A
Page 25 and 26: GUIDO RAYOS X, S.A.25supply tube.Ch
Page 27 and 28: GUIDO RAYOS X, S.A.27suitable. If i
Page 29 and 30: GUIDO RAYOS X, S.A.29ITEM REF. DESC
Page 31 and 32: GUIDO RAYOS X, S.A.312 2134105 6 7
Page 33 and 34: GUIDO RAYOS X, S.A.33Press Alarm Se
Page 35 and 36: GUIDO RAYOS X, S.A.35Alarms are sti
Page 37 and 38: GUIDO RAYOS X, S.A.37MAN-012Sept.00
Page 39 and 40: GUIDO RAYOS X, S.A.39VI. SERVICE.Se
Page 41 and 42: GUIDO RAYOS X, S.A.41• Set Simula
Page 43 and 44: GUIDO RAYOS X, S.A.43NUMBER REF. DE
Page 45 and 46: GUIDO RAYOS X, S.A.45WARRANTYGUIDO
Page 47: GUIDO RAYOS X, S.A.47MAN-012Sept.00

Download - Frank's Hospital Workshop

Create successful ePaper yourself

Delete template?

Save as template?