Bipap Pro 2 User Manual - NBN Group

More documents

Recommendations

Info

173. Attach the filter cap as shown in Figure 5–2. Position the cap so that the smallopening on the cap is facing down. Insert the caps bottom tabs into theopenings below the filter area. Snap the cap into place.Figure 5–2 Attaching the Filter CapNOTE:The filter cap should be installed with the air inlet opening at thebottom.See Chapter 9 to clean or replace the filters.5.2 WHERE TO PLACE THE DEVICEPlace the device on its base somewhere within easy reach of where you will use it.Make sure that the air inlet on the rear of the unit is not blocked. Place the unit ona hard, flat surface. If you block the air flow around the device, it may not workproperly.WARNING:If using an external humidifier, position the humidifier so thewater level is lower than you, and the humidifier is on the samelevel or lower than the device. See the humidifier instructions forcomplete setup information.User Manual
185.3 CONNECTING THE BREATHING CIRCUITTo connect your breathing circuit to the device, complete the following steps:1. Connect one end of the circuit tubing to the outlet of the bacteria filter (ifusing one) and connect the inlet of the bacteria filter to the large connector onthe device as shown in Figure 5–3.If you are not using a bacteria filter, connect the end of the circuit tubingdirectly to the outlet connector on the device.NOTE:Follow the recommendations of your home care provider for using theoptional bacteria filter.CircuitTubingBacteriaFilter(Optional)Figure 5–3 Connecting the Tubing to the Outlet2. Connect the tubing to the mask:A. If you are using a mask with a built-in exhalation port, connect themask’s connector to the circuit tubing, as shown in Figure 5–4.ExhalationPortMask'sConnectorFlexibleTubingConnectorFigure 5–4 Connecting a Mask with a Built-In Exhalation PortUser Manual
Page 1 and 2: pro 2- AND -User Manual
Page 4 and 5: CHAPTER 7: DEVICE ALERTS ..........
Page 6 and 7: 5CHAPTER 2: WARNINGS AND CAUTIONSWA
Page 8 and 9: 72.2 CAUTIONS• The device may onl
Page 10 and 11: 9OSARampRise TimeObstructive Sleep
Page 12 and 13: 113.3 SYMBOLSThe symbols shown belo
Page 14 and 15: 13NOTE:Additionally, if an alert oc
Page 16 and 17: 154.4 REAR PANELFigure 4-4 shows th
Page 20 and 21: 19B. If you are using a mask with a
Page 22 and 23: 215.5.1 USING AC POWERComplete the
Page 24 and 25: 23CHAPTER 6: OPERATING THE DEVICETh
Page 26 and 27: 253. Put on your mask assembly when
Page 28 and 29: 27Figure 6-7 shows how to navigate
Page 30 and 31: 29NOTE:These screens only display i
Page 32 and 33: 312. To increase or decrease the Fl
Page 34 and 35: 332. You can turn the patient disco
Page 36 and 37: 352. Medium Priority SoundThe mediu
Page 38 and 39: 37CHAPTER 8: TROUBLESHOOTINGThis ch
Page 40 and 41: 39Problem Why It Happened What To D
Page 42 and 43: 41CHAPTER 9: CLEANING AND MAINTENAN
Page 44 and 45: 43CHAPTER 10: ACCESSORIESThere are
Page 46 and 47: 45Fuses:There are no user-replaceab
Page 48 and 49: 47GUIDANCE AND MANUFACTURER’S DEC
Page 50 and 51: 49GUIDANCE AND MANUFACTURER’S DEC
Page 52 and 53: 51LIMITED WARRANTYRespironics, Inc.
Page 54: 1018989JH 1/22/04

Bipap Pro 2 User Manual - NBN Group

Create successful ePaper yourself

Delete template?

Save as template?