BrightStor CA-1 Tape Management - SupportConnect

More documents

Recommendations

Info

show a volser if either the TMACVOLI or the TMVTEXP flag bit is set, and should be hexzero otherwise.Any mismatch causes the ERR85 error to be issued.The misleading report lines "TMC LOW EXTENT IN HEX", "FIRST DSNB IN HEX" and "TMC DEVICECODE", which were printed at the end of the report and which referred to the allocation of the SYSUT3data set, have been removed.RESOLUTION:Documentation changes related to this enhancement:CA-1 5.2 Utilities and Reports Reference Guide1.38 TMSPTRS - Maintaining Multivolume/Multi-Data Set ChainsReplace the two paragraphs behind the caution box -TMSPTRS can be run without issuing a RESERVE against the TMC. This default option is valid only if thesame device type is used for SYSUT3 as is currently being used by the active TMC. A copy of the TMC ismade and then updated by applying all changes from the Audit data set that have occurred since the copyoperation began. Because it is necessary to apply the Audit records, TMSPTRS should not be run whileother CA-1 batch utilities, such as TMSCLEAN and TMSEXPDT, are running.If the device type specified in SYSUT3 is different than the device type of the active TMC, the ENQparameter must be specified. If the ENQ parameter is included, the active TMC is RESERVEd for theduration of the copy operation.with the following:TMSPTRS can be run without issuing a RESERVE against the TMC. A copy of the TMC is made and thenupdated by applying all changes from the Audit data set that have occurred since the copy operationbegan. Because it is necessary to apply the Audit records, TMSPTRS should not be run while other CA-1batch utilities, such as TMSCLEAN and TMSEXPDT, are running. If the ENQ parameter is specified, theactive TMC is RESERVEd for the duration of the copy operation.After the sentence -In the event TMSPTRS terminates with U0999 abend, R15 will indicate the cause:remove the entry for value 04:04 - SYSUT3 was referencing a device type unlike the one the TMC is on.1.38.1.1 Job Control StatementsIn the JCL box, change -//SYSUT3 DD UNIT=SYSDA,SPACE=(same as TMC)to://SYSUT3 DD UNIT=SYSDA,SPACE=(same as TMC) *NOTE 2PDC# QI35237
Note 2: The SYSUT3 data set holds a copy of the TMC. It may be blocked, regardless of whether the TMCitself is blocked or not. The BLKSIZE may be any multiple of the LRECL, which is 340.In the parameter definitions,ENQ Reserves the TMC for the length of the copy operation. This parameter is required if the device typespecified in SYSUT3 is not the same as the device type of the active TMC.remove the following sentence:This parameter is required if the device type specified in SYSUT3 is not the same as the device type of theactive TMC.1.38.6 TMS Report 29 - Invalid PointersAt the end of the displayed report, remove the following lines:TMC LOW EXTENT IN HEX CCHHR=02C1/0000/01FIRST DSNB IN HEXCCHHR=02CF/0000/22TMC DEVICE CODE =0E1.38.6.1 TMSPTRS Report Field DefinitionsRemove this section entirely:Message Error messageTMC LOW EXTENT IN HEXCylinder/head/track address of TMC copyFIRST DSNB IN HEXCylinder/head/track address of first DSNB record in TMC copyTMC DEVICE CODE Unit type device code of TMC copyUnit type device code of TMC copy2.32 TMSPTRS MessagesChange the description of ERR85 as follows:CA-1 5.2 Message GuideERR85 VOLUME xxxxxx HAS A CONFLICT BETWEEN FLAG4 (TMACVOLI) OR FLAG5(TMVTEXP) AND ACTVOLExplanation: Either the TMACVOLI bit of FLAG4 or the TMVTEXP bit of FLAG5 was on and ACTVOL wasblank, or ACTVOL was nonblank and both flag bits were off.PDC# QI35237
Page 1 and 2: BrightStor® CA-1® Tape Management
Page 5 and 6: COMPUTER ASSOCIATES INTERNATIONAL,
Page 7: • Data Erase UtilityA new Data Er
Page 10 and 11: Drop Support Date for Release 5.2:C
Page 12 and 13: This utility accepts input either v
Page 14 and 15: After all volumes have been written
Page 16 and 17: In this example, logical volumes LV
Page 18 and 19: QUERY COMPLETE, VOLUME IN ROBOT - A
Page 21 and 22: BrightStor CA-1 Product Documentati
Page 23 and 24: Note that a meaningful compression
Page 25 and 26: Replace line-----------------------
Page 27: with the following:----------------
Page 30 and 31: 1.28.3.1 Job Control Statements//st
Page 32 and 33: *** TESTRDS NOT VALID WITH DSNBS, T
Page 36 and 37: User response: If this is an AIVS v
Page 38 and 39: CA-1 Retention data set Rules (Opti
Page 40 and 41: Specification:If set to YES, the Cn
Page 42 and 43: Or no valid input command was found
Page 44 and 45: Thank you for your continued suppor
Page 46 and 47: For example, if volume 123456 is de
Page 48 and 49: CONCLUSION:In addition to these opt
Page 50 and 51: • TMSBLDVRThis section documents
Page 52 and 53: 4. TMSBINQ, the online TMSTIQ displ
Page 54 and 55: FOLLOW UP PROCEDURES AFTER INITIAL
Page 56 and 57: Appendix A., TMC Volume Definition
Page 58 and 59: User Response: None. Information on
Page 60 and 61: TMSXT05I ATTACH TMSBLDVR TO COPY/EX
Page 62 and 63: User Response: None. Information on
Page 64 and 65: TMSXT80E COULD NOT OBTAIN TMSVOLU T
Page 66 and 67: 52 82 EXTEND ALREADY ACTIVESee msg
Page 68 and 69: TMS REPORT-80 Report Field Definiti
Page 70 and 71: TMS REPORT-81 Report Field Definiti
Page 72 and 73: Eyy-112 I/O ERROR ON TMCExplanation
Page 74: (29 CPU entries in same format not

BrightStor CA-1 Tape Management - SupportConnect

Create successful ePaper yourself

Delete template?

Save as template?