BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

More documents

Recommendations

Info

OVERALLBATTERYBefore CalibrationAfter Calibration0.1% of reading 0.4VSelected InputDMM InputReadingOverall Battery(As-Found)DMM InputReadingOverall Battery(As-Left)+75V+350V+600VINTERTIER Before Calibration After Calibration0.1% of reading 1mVSelected InputDMM InputReadingIntertier(As-Found)DMM InputReadingIntertier(As-Left)INTERTIER 1+150mV+100mV+50mVINTERTIER 2+150mV+100mV+50mVINTERTIER 3+150mV+100mV+50mVINTERTIER 4+150mV+100mV+50mV76
INTERTIER Before Calibration After CalibrationSelected InputDMM InputReadingIntertier(As-Found)DMM InputReadingIntertier(As-Left)INTERTIER 5+150mV+100mV+50mVINTERTIER 6+150mV+100mV+50mVINTERTIER 7+150mV+100mV+50mVINTERTIER 8+150mV+100mV+50mVPREAMPOFFSETAND GAINBefore CalibrationAfter CalibrationSelected InputDMM InputReadingCurrent Count(As-Found)DMM InputReadingCurrent Count(As-Left)+100mV-100mV77
Page 5 and 6:
1. Warranty and Limitation of Liabi
Page 9 and 10:
Table of Contents1. WHAT'S NEW ....
Page 11:
15.8. Preamp Offset and Gain As-Fou
Page 14 and 15:
The manual has more screen shots. I
Page 16 and 17:
3. System RequirementsThe following
Page 18 and 19:
5. PasswordWhen you select certain
Page 20 and 21:
7. BCT-2000 Initial TestBefore conn
Page 22 and 23:
8. Main MenuThe main menu is where
Page 24 and 25:
9. Recommended TestsPrior to perfor
Page 26 and 27:
10. Connecting the SystemAfter perf
Page 28 and 29:
17. Connect the leads labeled IT-1(
Page 30 and 31:
Add Site / Delete Site - To add a s
Page 32 and 33:
11.4.1. Performance TestAlso known
Page 34 and 35:
11.4.4. Rundown TestA rundown test
Page 36 and 37:
11.5.3. Temperature and CorrectionA
Page 38 and 39: 11.5.7. Calculate Capacity at Targe
Page 40 and 41: 11.7. Load BankOn the Setup menu, c
Page 42 and 43: 11.8. ContactOn the Setup menu, cli
Page 44 and 45: Test Leads and Voltages - Click a b
Page 46 and 47: 20, 10, 5, 1 and All Off - You may
Page 48 and 49: 12.5. Test Screen ToolbarThe Toolba
Page 50 and 51: Figure 26. Test Steps - Constant Po
Page 52 and 53: 12.6. Charger Test ScreenWhen the C
Page 54 and 55: The Files of Type drop-down list le
Page 56 and 57: 13.5. Criteria ScreenClick the Crit
Page 58 and 59: Ignore Zero Target Steps in Capacit
Page 60 and 61: 13.9. Filter ScreenClick the Filter
Page 62 and 63: Change - Use the Properties dialog
Page 64 and 65: 13.17. Opening an Archive FileLoad
Page 66 and 67: 14. Running DiagnosticsThe DAM (Dat
Page 68 and 69: 14.3. Load Bank DiagnosticLoad bank
Page 70 and 71: Figure 50. Load Bank AnalysisThe Lo
Page 72 and 73: 15. System CalibrationThis section
Page 74 and 75: 15.4. Cell As-Found1. Complete the
Page 76 and 77: 15.8. Preamp Offset and Gain As-Fou
Page 78 and 79: 15.10. Cell Calibration1. Calibrate
Page 80 and 81: 15.12. Overall Battery Calibration1
Page 82 and 83: 15.14. Print a Calibration ReportAf
Page 84 and 85: 17. Upgrading BCT-2000 SoftwareUpgr
Page 86 and 87: 3. Select F2 Load Control Diagnosti
Page 90 and 91: 19. Run Time Error MessagesRun Time
Page 92 and 93: 21. Appendix A: BCT-128 Parts ListQ
Page 94 and 95: 23. Appendix C: Spare PartsBCT-2000
Page 96 and 97: constant power button .............
Page 98: Ssafety information ...............
show all

BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

Create successful ePaper yourself

Delete template?

Save as template?