BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber
BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber
3. Select F2 Load Control Diagnostics, and record the load bank step weights.Step Number1Step Weight234567891011121314154. Press ESC to return to the previous menu.5. Press ESC to return to the main menu, and press ESC to exit the program.6. Start the Windows BCT program by double-clicking the BCT icon. To open thecalibration dialog box, select Calibration from the main menu and enter the passwordalber. Type the Calibration K values recorded above.7. To open the Load Bank setup dialog box, select Load Bank from the Setup menu andenter the password alber. Type the shunt rating value recorded above. Type the loadbank step weights recorded above.8. If more than one load bank configuration is required, click the Add button and configurea second load bank. Repeat as necessary to complete the load bank configurations.9. The Windows BCT program is now ready for operation.74
18. BCT-2000 Calibration RecordCustomer ______________________________________________________________________________P.O. Number ___________________________________________________________________________Calibration Date ________________________________________________________________________System Serial No. ____________________________________________ Version ________________Configured Shunt (amps/mV) ______________________________________________________________Configured Load Bank Steps ______________________________________________________________Dwg. No. of Load Bank (if known) __________________________________________________________Computer Serial No. _____________________________________________________________________CELL Before Calibration After Calibration0.1% of reading 0.01VSelected InputDMM InputReadingCell(As-Found)DMM InputReadingCell(As-Left)+12V+2VOVERALLCURRENTBefore CalibrationAfter Calibration0.1% of reading 3ASelected InputDMM InputReadingOverall Current(As-Found)DMM InputReadingOverall Current(As-Left)+50mV+100mV+150mV-50mV-100mV-150mV75
- Page 36 and 37: 11.5.3. Temperature and CorrectionA
- Page 38 and 39: 11.5.7. Calculate Capacity at Targe
- Page 40 and 41: 11.7. Load BankOn the Setup menu, c
- Page 42 and 43: 11.8. ContactOn the Setup menu, cli
- Page 44 and 45: Test Leads and Voltages - Click a b
- Page 46 and 47: 20, 10, 5, 1 and All Off - You may
- Page 48 and 49: 12.5. Test Screen ToolbarThe Toolba
- Page 50 and 51: Figure 26. Test Steps - Constant Po
- Page 52 and 53: 12.6. Charger Test ScreenWhen the C
- Page 54 and 55: The Files of Type drop-down list le
- Page 56 and 57: 13.5. Criteria ScreenClick the Crit
- Page 58 and 59: Ignore Zero Target Steps in Capacit
- Page 60 and 61: 13.9. Filter ScreenClick the Filter
- Page 62 and 63: Change - Use the Properties dialog
- Page 64 and 65: 13.17. Opening an Archive FileLoad
- Page 66 and 67: 14. Running DiagnosticsThe DAM (Dat
- Page 68 and 69: 14.3. Load Bank DiagnosticLoad bank
- Page 70 and 71: Figure 50. Load Bank AnalysisThe Lo
- Page 72 and 73: 15. System CalibrationThis section
- Page 74 and 75: 15.4. Cell As-Found1. Complete the
- Page 76 and 77: 15.8. Preamp Offset and Gain As-Fou
- Page 78 and 79: 15.10. Cell Calibration1. Calibrate
- Page 80 and 81: 15.12. Overall Battery Calibration1
- Page 82 and 83: 15.14. Print a Calibration ReportAf
- Page 84 and 85: 17. Upgrading BCT-2000 SoftwareUpgr
- Page 88 and 89: OVERALLBATTERYBefore CalibrationAft
- Page 90 and 91: 19. Run Time Error MessagesRun Time
- Page 92 and 93: 21. Appendix A: BCT-128 Parts ListQ
- Page 94 and 95: 23. Appendix C: Spare PartsBCT-2000
- Page 96 and 97: constant power button .............
- Page 98: Ssafety information ...............
18. <strong>BCT</strong>-<strong>2000</strong> Calibration RecordCustomer ______________________________________________________________________________P.O. Number ___________________________________________________________________________Calibration Date ________________________________________________________________________System Serial No. ____________________________________________ Version ________________Configured Shunt (amps/mV) ______________________________________________________________Configured Load Bank Steps ______________________________________________________________Dwg. No. of Load Bank (if known) __________________________________________________________Computer Serial No. _____________________________________________________________________CELL Before Calibration After Calibration0.1% of reading 0.01VSelected InputDMM InputReadingCell(As-Found)DMM InputReadingCell(As-Left)+12V+2VOVERALLCURRENTBefore CalibrationAfter Calibration0.1% of reading 3ASelected InputDMM InputReadingOverall Current(As-Found)DMM InputReadingOverall Current(As-Left)+50mV+100mV+150mV-50mV-100mV-150mV75