BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

More documents

Recommendations

Info

17. Upgrading BCT-2000 SoftwareUpgrading the BCT-2000 software from the DOS to the Windows version involves the followingsteps. If you need assistance, contact Albércorp Technical Support.17.1. Replace the 87C52 ProcessorBefore the Windows BCT-2000 program can communicate with a BCT-128 or BCT-256 thatwas being used with the DOS BCT-2000 program, the 87C52 processor must be changed inthe BCT-128 or 256.1. Power down the BCT and disconnect it from AC power.2. Remove the six screws under plastic caps located along the sides of the BCT cover.3. Remove the cover.4. The 87C52 U21 processor is located in a socket on the right-most vertically mountedboard.5. At this point, the technician (you) should be connected to ground with a ground strap, oryou should discharge any static electricity by touching a grounded object.WARNING: Notice that the top corner of the socket closest to the front of the BCT isangled. You must align the angled corner of the new chip with this corner before installation.Failure to align the corners will damage the BCT.6. Using a PLCC chip puller, carefully remove U21 from its socket.CAUTION: The socket can easily be broken if you are not careful during removal andinstallation of the chips.7. Grasp the replacement U21 chip and install it in the socket, making certain that theangled corner of the chip is aligned with the angled corner of the socket.8. Replace the cover on the BCT, replace the six screws, and put the plastic caps over thescrews.9. Reconnect the BCT to power.72
17.2. Calibration Constants and Load Bank ConfigurationAfter installing the new Windows BCT software, you must properly configure the calibrationconstants and load banks before using the system. Record this information from the existingDOS program configuration files as follows:1. Start the DOS BCT program. From the main menu, select F4 Hardware Diagnostics, thenselect F1 Calibrate. Record the shunt setting and calibration (K) constants below.Shunt Rate Value:___________ Amps per ___________ millivoltsMeasurement PointCellCalibration KOverall CurrentOverall BatteryIntertier #1Intertier #2Intertier #3Intertier #4Intertier #5Intertier #6Intertier #7Intertier #82. Press ESC to return to the previous menu.73
Page 5 and 6:
1. Warranty and Limitation of Liabi
Page 9 and 10:
Table of Contents1. WHAT'S NEW ....
Page 11:
15.8. Preamp Offset and Gain As-Fou
Page 14 and 15:
The manual has more screen shots. I
Page 16 and 17:
3. System RequirementsThe following
Page 18 and 19:
5. PasswordWhen you select certain
Page 20 and 21:
7. BCT-2000 Initial TestBefore conn
Page 22 and 23:
8. Main MenuThe main menu is where
Page 24 and 25:
9. Recommended TestsPrior to perfor
Page 26 and 27:
10. Connecting the SystemAfter perf
Page 28 and 29:
17. Connect the leads labeled IT-1(
Page 30 and 31:
Add Site / Delete Site - To add a s
Page 32 and 33:
11.4.1. Performance TestAlso known
Page 34 and 35: 11.4.4. Rundown TestA rundown test
Page 36 and 37: 11.5.3. Temperature and CorrectionA
Page 38 and 39: 11.5.7. Calculate Capacity at Targe
Page 40 and 41: 11.7. Load BankOn the Setup menu, c
Page 42 and 43: 11.8. ContactOn the Setup menu, cli
Page 44 and 45: Test Leads and Voltages - Click a b
Page 46 and 47: 20, 10, 5, 1 and All Off - You may
Page 48 and 49: 12.5. Test Screen ToolbarThe Toolba
Page 50 and 51: Figure 26. Test Steps - Constant Po
Page 52 and 53: 12.6. Charger Test ScreenWhen the C
Page 54 and 55: The Files of Type drop-down list le
Page 56 and 57: 13.5. Criteria ScreenClick the Crit
Page 58 and 59: Ignore Zero Target Steps in Capacit
Page 60 and 61: 13.9. Filter ScreenClick the Filter
Page 62 and 63: Change - Use the Properties dialog
Page 64 and 65: 13.17. Opening an Archive FileLoad
Page 66 and 67: 14. Running DiagnosticsThe DAM (Dat
Page 68 and 69: 14.3. Load Bank DiagnosticLoad bank
Page 70 and 71: Figure 50. Load Bank AnalysisThe Lo
Page 72 and 73: 15. System CalibrationThis section
Page 74 and 75: 15.4. Cell As-Found1. Complete the
Page 76 and 77: 15.8. Preamp Offset and Gain As-Fou
Page 78 and 79: 15.10. Cell Calibration1. Calibrate
Page 80 and 81: 15.12. Overall Battery Calibration1
Page 82 and 83: 15.14. Print a Calibration ReportAf
Page 86 and 87: 3. Select F2 Load Control Diagnosti
Page 88 and 89: OVERALLBATTERYBefore CalibrationAft
Page 90 and 91: 19. Run Time Error MessagesRun Time
Page 92 and 93: 21. Appendix A: BCT-128 Parts ListQ
Page 94 and 95: 23. Appendix C: Spare PartsBCT-2000
Page 96 and 97: constant power button .............
Page 98: Ssafety information ...............
show all

BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

Create successful ePaper yourself

Delete template?

Save as template?