BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

More documents

Recommendations

Info

Figure 50. Load Bank AnalysisThe Load Bank Analysis dialog box has three columns of data for each load bank step: Load,Accumulative, and Vernier Gap. The Load column indicates how much current each step willdraw, based on the maximum OV value entered. The Accumulative column is the totalcurrent draw of the steps up to that point. The Vernier Gap is the difference between the stepLoad value and the Accumulative value of the previous steps. The highest Vernier Gapnumber indicates the minimum tolerance (in amps) of the load bank. Type this value plus 1on the Load Bank Advance Setup screen under Setup|Load Bank|Advance.To close the Load Bank Analysis screen, click X in the upper right corner. To close the StepsResistance box, click OK.Diagnostics Load Bank - On the Diagnostics Load Bank dialog box, click the appropriateStep 1 to 16 to turn on the step corresponding to the step number. If power is supplied to theload, the step resistance is displayed. Toggle the button to turn the step on or off. With nopower to the load bank, you may use an ohmmeter to read each step resistance.Results of the load bank diagnostics may be needed by Albércorp to assist in troubleshooting.14.4. BusTypically, this option is used only at the factory during product manufacturing and test. Aspecial bus analysis board is required. The screen displays technical diagnostics for circuitboards in the BCT-2000 system. It is not a user diagnostic screen and should only be usedwith the assistance of Albércorp technical personnel.58
Figure 51. Bus Diagnostics14.5. MiscThe Misc dialog box permits testing of the audible alarm inside the BCT. To test the alarm,click the Sonalert button to toggle the alarm on and off.Figure 52. Misc Diagnostics59
Page 5 and 6:
1. Warranty and Limitation of Liabi
Page 9 and 10:
Table of Contents1. WHAT'S NEW ....
Page 11:
15.8. Preamp Offset and Gain As-Fou
Page 14 and 15:
The manual has more screen shots. I
Page 16 and 17:
3. System RequirementsThe following
Page 18 and 19:
5. PasswordWhen you select certain
Page 20 and 21: 7. BCT-2000 Initial TestBefore conn
Page 22 and 23: 8. Main MenuThe main menu is where
Page 24 and 25: 9. Recommended TestsPrior to perfor
Page 26 and 27: 10. Connecting the SystemAfter perf
Page 28 and 29: 17. Connect the leads labeled IT-1(
Page 30 and 31: Add Site / Delete Site - To add a s
Page 32 and 33: 11.4.1. Performance TestAlso known
Page 34 and 35: 11.4.4. Rundown TestA rundown test
Page 36 and 37: 11.5.3. Temperature and CorrectionA
Page 38 and 39: 11.5.7. Calculate Capacity at Targe
Page 40 and 41: 11.7. Load BankOn the Setup menu, c
Page 42 and 43: 11.8. ContactOn the Setup menu, cli
Page 44 and 45: Test Leads and Voltages - Click a b
Page 46 and 47: 20, 10, 5, 1 and All Off - You may
Page 48 and 49: 12.5. Test Screen ToolbarThe Toolba
Page 50 and 51: Figure 26. Test Steps - Constant Po
Page 52 and 53: 12.6. Charger Test ScreenWhen the C
Page 54 and 55: The Files of Type drop-down list le
Page 56 and 57: 13.5. Criteria ScreenClick the Crit
Page 58 and 59: Ignore Zero Target Steps in Capacit
Page 60 and 61: 13.9. Filter ScreenClick the Filter
Page 62 and 63: Change - Use the Properties dialog
Page 64 and 65: 13.17. Opening an Archive FileLoad
Page 66 and 67: 14. Running DiagnosticsThe DAM (Dat
Page 68 and 69: 14.3. Load Bank DiagnosticLoad bank
Page 72 and 73: 15. System CalibrationThis section
Page 74 and 75: 15.4. Cell As-Found1. Complete the
Page 76 and 77: 15.8. Preamp Offset and Gain As-Fou
Page 78 and 79: 15.10. Cell Calibration1. Calibrate
Page 80 and 81: 15.12. Overall Battery Calibration1
Page 82 and 83: 15.14. Print a Calibration ReportAf
Page 84 and 85: 17. Upgrading BCT-2000 SoftwareUpgr
Page 86 and 87: 3. Select F2 Load Control Diagnosti
Page 88 and 89: OVERALLBATTERYBefore CalibrationAft
Page 90 and 91: 19. Run Time Error MessagesRun Time
Page 92 and 93: 21. Appendix A: BCT-128 Parts ListQ
Page 94 and 95: 23. Appendix C: Spare PartsBCT-2000
Page 96 and 97: constant power button .............
Page 98: Ssafety information ...............
show all

BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

Create successful ePaper yourself

Delete template?

Save as template?