BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

More documents

Recommendations

Info

12.5. Test Screen ToolbarThe Toolbar buttons that appear along the top of the BCT Test screen are shown below.Figure 22. BCT Test ToolbarUse the buttons to exclude or include cells that went into shutdown; change alarm levels;change test step duration and load; change the number of graph grid lines; zoom in on a baraxis; and view the alarms list. These buttons are described in the following sections.12.5.1. Cell ExclusionExclude CellsTo remove a cell from the test, click the Exclude Cells button. In the Cell Exclusionsdialog box, click Add Cell, type the string and cell number, then click Exclude. Thestring and cell appear in the list in the Cell Exclusions dialog box. A box with a checkmark indicates the cell is excluded from the test. To include an excluded cell back intothe test, clear the check box. You can exclude cells before a test, and during a test withoutpausing the test. You can include them back during a test without pausing.Excluding and including a cell from the test automatically adjusts battery alarm levels bychanging the OV warning and shutdown values by one cell level. All items on the cellexclusion list are cleared when the test is exited.Figure 23. Cell Exclusions12.5.2. Alarm LevelsAdjust Alarm LevelsYou may change the warning and shutdown levels for cells, OV, and intertiers while thetest is running. Click the Adjust Alarm Levels toolbar button. After changing a level, usethe TAB or ENTER key or mouse to move to the next box. The new alarm level takeseffect immediately. Changes are recorded in the test activities portion of the report.36
CAUTION: Changes made to the alarm levels and test steps using the Test Adjustmentsdialog boxes are valid only for the presently running test and do not permanently changethe test setup information.Figure 24. Alarm Levels12.5.3. Test StepsAdjust Test StepsClick Adjust Test Steps to add new steps or change the duration or load of the presentlyrunning step or subsequent steps. NOTE: You cannot change the duration of a presentlyrunning step to less than the elapsed time of the step. Also, steps that have already runcannot be changed. To add a new step, click Add Step.Figure 25. Test Steps - Constant CurrentIf Constant Current is selected, the Test Steps dialog box has buttons for 20, 10, 5 and 1amp, or you may type a new value in the Amps column.37
Page 5 and 6: 1. Warranty and Limitation of Liabi
Page 9 and 10: Table of Contents1. WHAT'S NEW ....
Page 11: 15.8. Preamp Offset and Gain As-Fou
Page 14 and 15: The manual has more screen shots. I
Page 16 and 17: 3. System RequirementsThe following
Page 18 and 19: 5. PasswordWhen you select certain
Page 20 and 21: 7. BCT-2000 Initial TestBefore conn
Page 22 and 23: 8. Main MenuThe main menu is where
Page 24 and 25: 9. Recommended TestsPrior to perfor
Page 26 and 27: 10. Connecting the SystemAfter perf
Page 28 and 29: 17. Connect the leads labeled IT-1(
Page 30 and 31: Add Site / Delete Site - To add a s
Page 32 and 33: 11.4.1. Performance TestAlso known
Page 34 and 35: 11.4.4. Rundown TestA rundown test
Page 36 and 37: 11.5.3. Temperature and CorrectionA
Page 38 and 39: 11.5.7. Calculate Capacity at Targe
Page 40 and 41: 11.7. Load BankOn the Setup menu, c
Page 42 and 43: 11.8. ContactOn the Setup menu, cli
Page 44 and 45: Test Leads and Voltages - Click a b
Page 46 and 47: 20, 10, 5, 1 and All Off - You may
Page 50 and 51: Figure 26. Test Steps - Constant Po
Page 52 and 53: 12.6. Charger Test ScreenWhen the C
Page 54 and 55: The Files of Type drop-down list le
Page 56 and 57: 13.5. Criteria ScreenClick the Crit
Page 58 and 59: Ignore Zero Target Steps in Capacit
Page 60 and 61: 13.9. Filter ScreenClick the Filter
Page 62 and 63: Change - Use the Properties dialog
Page 64 and 65: 13.17. Opening an Archive FileLoad
Page 66 and 67: 14. Running DiagnosticsThe DAM (Dat
Page 68 and 69: 14.3. Load Bank DiagnosticLoad bank
Page 70 and 71: Figure 50. Load Bank AnalysisThe Lo
Page 72 and 73: 15. System CalibrationThis section
Page 74 and 75: 15.4. Cell As-Found1. Complete the
Page 76 and 77: 15.8. Preamp Offset and Gain As-Fou
Page 78 and 79: 15.10. Cell Calibration1. Calibrate
Page 80 and 81: 15.12. Overall Battery Calibration1
Page 82 and 83: 15.14. Print a Calibration ReportAf
Page 84 and 85: 17. Upgrading BCT-2000 SoftwareUpgr
Page 86 and 87: 3. Select F2 Load Control Diagnosti
Page 88 and 89: OVERALLBATTERYBefore CalibrationAft
Page 90 and 91: 19. Run Time Error MessagesRun Time
Page 92 and 93: 21. Appendix A: BCT-128 Parts ListQ
Page 94 and 95: 23. Appendix C: Spare PartsBCT-2000
Page 96 and 97: constant power button .............
Page 98:
Ssafety information ...............
show all

BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

Create successful ePaper yourself

Delete template?

Save as template?