BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

More documents

Recommendations

Info

11.4.4. Rundown TestA rundown test is similar to a service test, except the test uses the system load instead ofa controlled load. Rundown has only one step and no shutdown levels.Figure 10. Setup - Test Setup: Rundown11.4.5. Charger TestWhen the charger test is selected, the only parameters recorded to the report file areOverall Voltage and Current.Figure 11. Setup - Test Setup: Charger22
11.4.6. Recharge TestThe recharge test monitors the battery system while it is being recharged. For every twocell volts, the cell warning level is set to 2.33V. The OV warning levels are a multiple ofthese levels times the number of cells per string. On this test, the levels are high level(maximum) values.Figure 12. Setup - Test Setup: Recharge11.5. Test Setup ParametersThe following items are available on the Test Setup dialog boxes depending on the test typeselected.11.5.1. Rated TimeAvailable for test types: Performance, Modified PerformanceType the manufacturer’s specified rated time in the Rated Time box. This value isimportant for the on-line capacity calculation performed during a single step capacitytest. The format is hh:mm:ss. If doing a Modified Performance test, you may leave RatedTime blank.You may type 0 (zero) for Rated Time on a Modified Performance test. If this is done,the test does not calculate battery capacity at test time. You may enter a Rated Time atreport generation.11.5.2. Power TypeAvailable for test types: Performance, Modified Performance, Service, ChargerConstant Power and Constant Current - To define power type, click Constant Power orConstant Current. Power type determines if the programmed load is rated in watts oramps. The power type selected applies to all steps; you cannot switch between ConstantPower and Constant Current between steps.23
Page 5 and 6: 1. Warranty and Limitation of Liabi
Page 9 and 10: Table of Contents1. WHAT'S NEW ....
Page 11: 15.8. Preamp Offset and Gain As-Fou
Page 14 and 15: The manual has more screen shots. I
Page 16 and 17: 3. System RequirementsThe following
Page 18 and 19: 5. PasswordWhen you select certain
Page 20 and 21: 7. BCT-2000 Initial TestBefore conn
Page 22 and 23: 8. Main MenuThe main menu is where
Page 24 and 25: 9. Recommended TestsPrior to perfor
Page 26 and 27: 10. Connecting the SystemAfter perf
Page 28 and 29: 17. Connect the leads labeled IT-1(
Page 30 and 31: Add Site / Delete Site - To add a s
Page 32 and 33: 11.4.1. Performance TestAlso known
Page 36 and 37: 11.5.3. Temperature and CorrectionA
Page 38 and 39: 11.5.7. Calculate Capacity at Targe
Page 40 and 41: 11.7. Load BankOn the Setup menu, c
Page 42 and 43: 11.8. ContactOn the Setup menu, cli
Page 44 and 45: Test Leads and Voltages - Click a b
Page 46 and 47: 20, 10, 5, 1 and All Off - You may
Page 48 and 49: 12.5. Test Screen ToolbarThe Toolba
Page 50 and 51: Figure 26. Test Steps - Constant Po
Page 52 and 53: 12.6. Charger Test ScreenWhen the C
Page 54 and 55: The Files of Type drop-down list le
Page 56 and 57: 13.5. Criteria ScreenClick the Crit
Page 58 and 59: Ignore Zero Target Steps in Capacit
Page 60 and 61: 13.9. Filter ScreenClick the Filter
Page 62 and 63: Change - Use the Properties dialog
Page 64 and 65: 13.17. Opening an Archive FileLoad
Page 66 and 67: 14. Running DiagnosticsThe DAM (Dat
Page 68 and 69: 14.3. Load Bank DiagnosticLoad bank
Page 70 and 71: Figure 50. Load Bank AnalysisThe Lo
Page 72 and 73: 15. System CalibrationThis section
Page 74 and 75: 15.4. Cell As-Found1. Complete the
Page 76 and 77: 15.8. Preamp Offset and Gain As-Fou
Page 78 and 79: 15.10. Cell Calibration1. Calibrate
Page 80 and 81: 15.12. Overall Battery Calibration1
Page 82 and 83: 15.14. Print a Calibration ReportAf
Page 84 and 85:
17. Upgrading BCT-2000 SoftwareUpgr
Page 86 and 87:
3. Select F2 Load Control Diagnosti
Page 88 and 89:
OVERALLBATTERYBefore CalibrationAft
Page 90 and 91:
19. Run Time Error MessagesRun Time
Page 92 and 93:
21. Appendix A: BCT-128 Parts ListQ
Page 94 and 95:
23. Appendix C: Spare PartsBCT-2000
Page 96 and 97:
constant power button .............
Page 98:
Ssafety information ...............
show all

BCT-2000 Software and BCT-128 and BCT-256 User's Guide - Alber

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?